• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.23 no.1
• /
• pp.89-96
• /
• 2005

With acquisition of satellite image being facilitated due to recent advancement in Electro optical and astronautic technologies, focus on establishment of Geoinformation and analysis using satellite images have increased. This research have conducted digital plotting and digitizing operation, utilizing stereo images and grey level images provided by SPOT5 satellite and evaluated the accuracy through comparison and analysis with digital map results. Digital plotting results acquired using stereo images have been compared and analyzed on the basis of scale 1:25,000 digital map results published by National Geographic Information Institute. Accuracy of 20 check points have showed RMSE results 5.369 m at X (Easting) and 4.718 m, digitizing using grey level images showed RMSE results 7.616 m in X (Easting) and Y (Northing) 6.532 m. This is within the allowance of accuracy standards for scale 1:25,000 maps, and although digitizing operation was confirmed to have lower accuracy than that of digital plotting, using the former is considered to be more effective in terms of economical efficiency.

• Korean Journal of Remote Sensing
• /
• v.18 no.4
• /
• pp.221-231
• /
• 2002

In this study we applied a DEM generation algorithm developed in-house to satellite images at various resolution and discussed the results. We tested SPOT images at l0m resolution, EOC images at 6.6m and IKONOS images at 1m resolution. These images include the same urban area in Daejeon city. For camera model, we used Gupta & Hartley's(1997) DLT model for all three image sets. We carried out accuracy assessment using USGS DTED for SPOT and EOC and 23 check points for IKONOS. The assessment showed that SPOT DEM had about 38m RMS error, EOC DEM 12m RMS error and IKONOS DEM 6.5m RMS error. In terms of image resolution, SPOT and EOC DEM error corresponds to 2∼4 pixels where as IKONOS DEM error 6∼7pixels. IKONOS DEM contains more errors in pixels. However, in IKONOS DEM, individual buildings, apartments and major roads are identifiable. All three DEMs contained errors due to height discontinuity, occlusion and shadow. These experiments show that our algorithm can generate urban DEM from 1m resolution and that, however, we need to improve the algorithm to minimize effects of occlusion and building shadows on DEMs.

• Spatial Information Research
• /
• v.16 no.2
• /
• pp.193-206
• /
• 2008

If stereo images is used for Digital Elevation Model (DEM) generation, a DEM is generally made by matching left image against right image from stereo images. In stereo matching, tie-points are used as initial match candidate points. The number and distribution of tie-points influence the matching result. DEM made from matching result has errors such as holes, peaks, etc. These errors are usually interpolated by neighbored pixel values. In this paper, we propose the DEM generation method combined with automatic tie-points extraction using existing DEM, image pyramid, and interpolating new DEM using existing DEM for more reliable DEM. For test, we used IKONOS, QuickBird, SPOT5 stereo images and a DTED level 2 data. The test results show that the proposed method automatically makes reliable DEMs. For DEM validation, we compared heights of DEM by proposed method with height of existing DTED level 2 data. In comparison result, RMSE was under than 15 m.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.27 no.5
• /
• pp.529-534
• /
• 2009

In this study, we investigate the feasibility of modeling entire image strips that has been acquired from the same orbital segments. We tested sensor models based on satellite orbit and attitude with different sets(Type1 ~ Type4) of unknowns. We checked the accuracy of orbit modeling by establishing sensor models of one scene using control points extracted from the scene and by applying the models to adjacent scenes within the same orbital segments. Results indicated that modeling of individual scenes with 1st or 2nd order unknowns was recommended. We tested the accuracy of around control points, digital map using the HIST-DPW (Hanjin Information Systems & Telecommunication Digital Photogrammetric Workstation) As a result, we showed that the orbit-based sensor model is a suitable sensor model for making 1/25,000 digital map.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2003.04a
• /
• pp.245-248
• /
• 2003

본 연구에서는 수치영상처리 방법으로 공간해상도가 l0m인 SPOT 흑백영상을 사용하여, 지상기준점 수량을 10∼30개까지 5개 단위로 증가시키면서 각각의 모델링과 수치표고모델, 정사영상을 생성하여 정사영상상에서 정확도를 평가하였다.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.21 no.1
• /
• pp.61-69
• /
• 2003

There is various kinds cause that influence to created DEM and orthoimage using stereo satellite images. Specialty, research about effect that GCP number gives to accuracy of DEM, orthoimage and modeling may have to be gone ahead. Therefore, this research increases GCP number by 5 to 30 and created each modeling, DEM and orthoimage using SPOT panchromatic images that resolution is 10m by digital image processing method. Accuracy assessment did by orthoimage using 20 check point. As a result, GCP number between 10∼30 modeling RMSE is 1 pixel low appear. Horizontal·vertical error that use orthoimage looked tendency that decrease GCP number increases, and confirmed by the most economical in GCP number 10∼15. Also, analyze correlation of GCP number and orthoimage position accuracy and presented improvement plan and research task hereafter.

• Journal of Korean Society for Geospatial Information Science
• /
• v.10 no.5 s.23
• /
• pp.53-65
• /
• 2002

The most widespread techniques for DEM generation are stereoscopy for optical sensor images and SAR interferometry(InSAR) for SAR images. These techniques suffer from certain sensor and processing limitations, which can be overcome by the synergetic use of both sensors and DEMs respectively. This study is associated with improvements of accuracy with consistency of image's characteristics between two different DEMs coming from stereoscopy for the optical images and interferometry for SAR images. The MWD(Multiresolution Wavelet Decomposition) and HPF(High-Pass Filtering), which take advantage of the complementary properties of SAR and stereo optical DEMs, will be applied for the fusion process. DEM fusion is tested with two sets of SPOT and ERS-l/-2 satellite imagery and for the analysis of results, DEM generated from digital topographic map(1 to 5000) is used. As a result of an integration of DEMs, it can more clearly portray topographic slopes and tilts when applying the strengths of DEM of SAR image to DEM of an optical satellite image and in the case of HPF, the resulting DEM.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.26 no.4
• /
• pp.359-365
• /
• 2008

This paper focused on generation of more accurate DEM and analysis of accuracy. For this, we applied suitable sensor modeling technique for each satellite image and automatic pyramid matching using image pyramid was applied. Matching algorithm based on epipolarity and scene geometry also was applied for stereo matching. IKONOS, Quickbird, SPOT-5, Kompsat-2 were used for experiments. In particular, we applied orbit-attitude sensor modeling technique for Kompsat-2 and performed DEM generation successfully. All DEM generated show good quality. Assessment was carried out using USGS DTED and we also compared between DEM generated in this research and DEM generated from common software. All DEM had $9m{\sim}12m$ Mean Absolute Error and $13m{\sim}16m$ RMS Error. Experimental results show that the DEMs of good performance which is similar to or better than result of DEMs generated from common software.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.19 no.3
• /
• pp.291-300
• /
• 2001

In this paper, we developed a Satellite Image Processing System for obtaining 3-D positional information which is composed of five process modules. As a procedure of them, the Data Process module is the procedure that reads and processes the header file to generate data files. and then calculates orbital parameters and sensor attitudes for obtaining of 3-D positional information with them. The 3D Process module is to calculate 3-D positional information and the Dialog Process module is to correct the time of image frame center using the single image or stereo images for implementing the 3D Process module. We expect to obtain 3-D positional information with the header file and minimum GCPs(1∼2 points) using this system efficiently and economically in comparison with existing commercial software packages.