• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.4
• /
• pp.643-650
• /
• 2017

This pap4er analyzes resonance characteristics of a slave motor that is not controlled by load and parameter differences between Dual motors during parallel operation in middle-low speed. Dual SPMSMs(Surface mounted Permanent Magnet Synchronous Motor) connected in parallel to a single inverter controlled by the master and slave control in this paper. Based on the stability analysis of the SPMSM for a variation of torque angle, the 6th nonlinear state equation of the torque angle variation in the SIMM(Single Inverter Multi Motor) structure is derived according to a mathematical model for the dual motors. In general, an analysis of the 6th order nonlinear state equation is complex. Therefore, a resonance frequency generated from the slave motor is found from the characteristic equation of the 2nd order system obtained by linearization and model reduction near steady state operation point. Through simulations and experiments, it is confirmed that the stability analysis of the SPMSMs and state equation models are useful for the variation of the torque angle analyzed in this paper.

• Journal of Power Electronics
• /
• v.17 no.5
• /
• pp.1211-1222
• /
• 2017

In order to decrease the parameter sensitivity of deadbeat direct torque control (DB-DTC), an improved deadbeat direct torque control method for surface mounted permanent-magnet synchronous motor (SPMSM) drives is proposed. First, the track errors of the stator flux and torque that are caused by model parameter mismatch are analyzed. Then a sliding mode observer is designed, which is able to predict the d-q axis currents of the next control period for one-step delay compensation, and to simultaneously estimate the model parameter disturbance. The estimated disturbance of this observer is used to estimate the stator resistance offline. Then the estimated resistance is required to update the designed sliding-mode observer, which can be used to estimate the inductance and permanent-magnetic flux linkage online. In addition, the flux and torque estimation of the next control period, which is unaffected by the model parameter disturbance, is achieved by using predictive d-q axis currents and estimated parameters. Hence, a low parameter sensitivity DB-DTC method is developed. Simulation and experimental results show the validity of the proposed direct control method.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.10
• /
• pp.74-81
• /
• 2006

This paper proposes the sensorless vector control scheme of a Non-salient permanent-magnet synchronous motor (SPMSM) using programmable low pass filter (PLPF) to estimate a stator flux with the information of a rotor position and speed. The sesorless vector control of PMSM using PLPF can solves the dc drift problem associated with a pure integrator and a LPF. Also, the PLPF has the phase and gain compensator to estimate exactly rotor position and speed. Therefore, the information of a position and speed is exactly estimated because the drift and offset problems are solved by the PLPF. The experimental results show good performance over the 10[%] of the rated speed and under load condition.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.765-766
• /
• 2006

Interior Permanent Magnet Synchronous Motor(IPMSM) have many advantages such as high power density, wide speed range and so on. With the IPMSM, miniaturization and energy efficient design can be achieved in comparison with Surface Permanent Magnet Synchronous Motor(SPMSM). In order to secure miniaturization and manufacturing efficiency of the motor, it has concentrated winding, because concentrated winding can reduce the motor volume and make manufacturing to be simple compared with the distributed winding. However, according to the pole-slot combinations motor parameters can be changed and unexpected normal force can be generated. Especially, unbalanced normal force in airgap can cause serious vibration and acoustic problem. Accordingly, in this paper, normal force and parameters variation of concentrated winding IPMSM are investigated according to the pole-slot combinations.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.12
• /
• pp.1119-1124
• /
• 2013

In this paper we propose a novel torque control method for permanent magnet synchronous motors using the SVPWM (Space Vector PWM). The control law is described in the rotating d-q frame and is devised to track a given reference flux with which the reference torque is generated. The key feature of the proposed control is that it provides uniform dynamics with desired closedloop poles independent of the rotating speed and the desired poles can be selected to yield a fast response with only a small amount of torque ripple.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.2 no.2
• /
• pp.216-224
• /
• 2013

This paper describes dual inverter drive for a fractional-slot concentrated winding permanent magnet synchronous machine (PMSM). PMSMs are widely used in many applications from small servo motors to few megawatts generators thanks to its high efficiency and torque density. Especially, fractional-slot concentrated winding PMSM is very popular in the applications where wide operation range is required because it shows very wide constant power speed ratios. High speed operation, however, requires lots of negative daxis current for reducing back-EMF regardless of output torque. Field weakening current does not contribute to the torque generation in surface mounted PMSM case and causes inverter and copper loss. To reduce the losses from field weakening current, this paper proposes PMSM with split stator and parallel dual inverter drive. Proposed parallel dual inverter drive reduces back-EMF and enables efficient drive at high speed and light load situation. Control strategy of proposed dual inverter system is established through loss analysis and simulation. Proposed concept is verified with practical experiment.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.72-81
• /
• 2018

In this study, the sinusoidal-wave driving method, six-step driving method, and twelve-step driving method, which can be used in an inverter for permanent-magnet synchronous motors, were simulated, and the results were compared to review their operating performance. These driving methods were classified according to the electrical conduction angle and phase current of the motor. Conventionally, only the transition control technique between the sinusoidal-wave driving method and six-step driving method was studied for the efficiency of the inverter. In this paper, however, comparative analysis was focused on a variety of transition control applications to use the advantages of each driving method. For this purpose, computer simulations for these driving methods were carried out to obtain the motor torque, speed control characteristics, and THD of the motor phase currents. As a result, the sinusoidal-wave driving method showed the best performance in all respects. The six-step driving method has better speed control characteristics than the twelve-step driving method, and the twelve-step driving method has a lower THD of the motor phase currents than the six-step driving method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.755-760
• /
• 2016

The demand for independent generators using renewable energy has been increasing. Among those independent generators, small wind turbine generators have been actively developed. Permanent magnets are generally used for small wind turbine generators to realize a simple structure and small volume. On the other hand, cogging torque is included due to the structure of the permanent magnet synchronous machine, which can be the source of noise and vibration. The cogging torque can be varied by the shape of the permanent magnet and core, and it can be reduced using the appropriate design techniques. This paper proposes a design technique that can reduce the cogging torque by changing the shape of the permanent magnets for SPMSM (Surface Permanent Magnet Synchronous Motor), which is used widely for small wind turbine generators. Evolution Strategy, which is one of non-deterministic optimization techniques, was adopted to find the optimal shape of the permanent magnets that can reduce the cogging torque. The angle and outer diameter of permanent magnet were set as the design variable. A 300W class wind turbine generator, whose pole/slot combination was 8 poles/18 slots, was designed with the proposed design technique. The properties of the generator, including the cogging torque and output voltage, were calculated. The calculation results showed that the cogging torque of the optimized model was reduced compared to that of the initial model. The design technique proposed by this paper can be an effective measure to reduce the cogging torque.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.3
• /
• pp.243-254
• /
• 2014

It is essential to predict the coil temperature under over load and over speed conditions for reliability in high speed low torque surface mounted PM synchronous motors(SPM). In the present study, the losses and coil temperature are measured under rated condition and calculated under over speed and over load conditions in the three different motors with 35PN440, 25PN250 and 15HTH1000. The heat transfer modeling has been performed based on acquired losses and temperature. The difference of coil temperature between heat transfer modeling and experiment is less than 6.4% under no load, over speed and over load conditions. Subsequently, the coil temperature of the motor with 15HTH1000 is 84.4% of the coil temperature of the motor with 35PN440 when speed is 0.9 and load is 3.0. The output of motor with 15HTH1000 is 85.2% greater than the output of the motor with 35PN440 when the dimensionless coil temperature is 1.0.