• 대한치과보철학회지
• /
• 제41권4호
• /
• pp.476-492
• /
• 2003

Purpose : The purpose of this study was to compare HEMA and TEGDMA as diluents for the composite resin. Material and methods : Eight kinds of experimental light curable composite resins were prepared and used. Concentrations of monomer and filler were same for all experimental composites, except, the diluent's ratios to the monomer. The ratio of diluents to Bis-GMA were 15%, 20%, 25%, and 30%, and two kinds of diluents were used, so total experimental groups were eight including one control group of 25% TEGDMA. Results : Depth of cure, flexural strength, shear bond strength to bovine enamel, shear bond strength to bovine dentin, water absorption and solubility of composites in water were measured. Sample size for each groups were 10. Arithmetic means were used as each groups representative values, and regression test for two diluents and low concentrations, Duncan's multiple range test, and Two-way ANOVA test were done for kinds of diluents and its concentrations at level of 0.05. Conclusion : Following results were obtained ; 1. There were not significant differences in effects of HEMA and TEGDMA to depth of cure, flexural strength of composites and shear bond strength to bovine enamel (p>0.05). 2. Increase of the concentrations of the diluents made the depth of cure (p<0.001) and flexural strength (p<0.05) a little higher. 3. Shear bond strength to dentin was higher on HEMA containing composites than TEGDMA containing composites (p<0.001). 4. Water absorption was higher on HEMA containing composites than TEGDMA containing composites (p<0.01).

• 대한치과교정학회지
• /
• 제28권5호
• /
• pp.689-698
• /
• 1998

법랑질의 표면처리에 따른 광중합형 글래스아이오노머 시멘트의 전단결합강도를 알아보고자 사람 소구치 80개를 선택하여 8개군으로 나누어 전단 결합 강도를 측정하고, 접착 파절의 양상을 평가하여 다음과 같은 결과를 얻었다. $1.37\%$ 인산용액으로 부식한 후 건조상태에서 글래스아이오노머 시멘트, 광중합형 레진, 화학중합형 레진으로 각각 부착한 실험군에서 글래스아이오노머 시멘트 실험군의 전단결합강도는 두 군과 유의한 차가 없었으나 화학중합형 레진군의 그것은 광중합형 레진군에 비해 유의성있게 낮았다 (p<0.05). $2.37\%$ 인산 실험군, $10\%$ 폴리 아크릴산 실험군, $1.23\%$ APF 실험군, 산처리하지 않은 실험군의 습한 상태에서 부착한 글래스아이오노머 시멘트의 전단결합강도에서 산처리하지않은 실험군의 그것이 유의성 있게 낮았으며, 그 외 군간에는 유의성 있는 차이가 없었다 (p<0.05). 3. 글래스아이오노머 실험군에서 습기의 존재가 전단결합강도에 유의성 있는 영향을 미치지 않았다 (p<0.05). 4. 산부식처리를 하지않은 군의 접착제 잔류지수가 가장 낮았으며 $37\%$인산용액으로 처리한 군의 접착제 잔류지수가 가장 높았다.

• 콘크리트학회지
• /
• 제8권4호
• /
• pp.149-159
• /
• 1996

최근의 건설 재료의 발전은 인공경량골재의 대량생산을 가능케 했으며 이를 사용한 경량고강도콘크리트의 발전을 가속화시켰다. 경량고강도콘크리트는 Dead Load를 감소시켜 건설비용을 경감시킬 뿐만 아니라 자중 감소로 인하여 지진 등에도 적절히 대응할 수 있는 재료이다. 그러나 대부분의 연구가 보통중량 골재를 사용한 고강도 콘크리트에 대한 연구이고, 경량골재를 사용한 고강도콘크리트에 대해서는 그 연구 결과가 많지 않다. 일반적으로 철근콘크리트 보의 전단강도는 콘크리트의 압축강도, 인장철근비, 전단스팬비, 그리고 전단보강철근의 유무에 영향을 받는다고 한다. 이에 본 연구에서는 전단스팬비(a/d = 1.5, 2.5, 3.5, 4.5)와 전단보강철근( ${\rho}_8= 0%$, 1.136%)을 변수로 한 총 8개의 시험체를 가지고 경량고강도콘크리트의 전단거동에 관한 특성을 규명하고자 전단실험을 행했다. 실험결과들은 ACI 규준식 및 Zsutty의 제안식과 비교 검토되었다. 그 결과 ACI(11-3)식과 (11-6)식은 경량콘크리트 보에서도 적용 가능하고, 또한 Zsutty 의 제안식도 전단스팬비(a/d)가 1.5인 경우를 제외하고는 적용될 수 있음을 알 수 있었다.

• 콘크리트학회논문집
• /
• 제18권5호
• /
• pp.611-620
• /
• 2006

보의 전단 메커니즘을 구성하는 보 작용과 아치 작용은 전단경간비(a/d)에 따라 그 존재 비율이 바뀔 뿐, 항상 공존한다. 그러나 대부분의 제안식들은 이를 함께 고려하지 않으며, 단순히 a/d=2.5를 기준으로 식의 형태를 나누어 제시하는 것에 그치고 있다. 또한 현 설계 기준은 과거의 일반 강도 콘크리트를 기준으로 설립되었기 때문에, 현재 사용 추세가 점차 증가하고 있는 고강도 콘크리트에 적용하기에는 다소 한계점이 있다. 이러한 문제점을 보완하고자, 본 연구에서는 a/d의 범위에 구애받지 않으며 고강도의 콘크리트에서도 사용이 가능한 전단 강도 예측식을 제안하였다. 보 작용과 아치 작용을 동시에 고려하기 위해 Jenq과 Shah 모델을 바탕으로 축방향에 따른 철근의 응력 변화를 산정하여, 단면의 모멘트로부터 전단 강도를 산출하였다. 보다 정확한 예측식의 제안을 위하여 장부 작용과 전단 마찰과 같은 2차적인 작용들 역시 제안식에 포함시켰으며, 크기 효과도 반영하였다. 식의 상수를 결정하고 식의 형태를 간략화하기 위해 다량의 실험 자료를 이용하여 회귀분석을 실시하였다. 제안식을 콘크리트의 압축강도($f'_c$), 전단경간비(a/d), 철근비($\rho$), 보의 유효 깊이(d), 철근의 항복강도($f_y$)의 변수를 기준으로 기존의 식들과 비교 검증한 결과, 제안식이 보다 정확하고 합리적인 예측을 하는 것으로 판명되었다. 또한 제안식의 변수별 거동 양상 역시 실험값과 비교적 일치하는 것으로 나타났다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 봄 학술발표회 논문집
• /
• pp.431-438
• /
• 1999

An assessment of liquefaction potential is made in principle by comparing the shear stress induced by earthquake to the liquefaction strength of the soil. In this study, a modified method based on Seed and Idriss theory is developed for evaluating liquefaction potential. The shear stress in the ground can be evaluated with seismic response analysis and the liquefaction strength of the soil can be investigated by using cyclic triaxial tests. The cyclic triaxial tests are conducted in two different conditions in order to investigate the factors affecting liquefaction strength such as cyclic shear stress amplitude and relative density. And performance of the modified method in practical examples is demonstrated by applying it to liquefaction analysis of artificial zones with dimensions and material properties similar to those in a typical field. From the result, the modified method for assessing liquefaction potential can successfully evaluate the safety factor under moderate magnitude(M=6.5) of earthquake.

• 한국환경복원기술학회지
• /
• 제4권3호
• /
• pp.49-54
• /
• 2001

It is common that the soil layer is a few meters below the earth's surface and the rock mass is below the soil layer in the view of geological characteristics in Korea. And the boundary between rock and soil is clearly divided. When dealing with the stability of rock masses, as in the case of rock slopes or dam foundations, the majority of the collapses is not within the soil layer, but within the soil-rock boundary. Therefore it is important to identify the shear strength characteristics between soil-rock boundary. And then in the method of reinforcement on landslide this chose a cut slope near Daemo elementary school in Seoul, surveyed shear strength between soil-rock contacts and considered a large scale collapse using a limit equilibrium method.

• Journal of Welding and Joining
• /
• 제30권6호
• /
• pp.62-67
• /
• 2012

In this study, the bonding strengths of adhesively bonded joints are experimentally investigated. A series of lap-shear tests are conducted using single lap type adhesive joints. In order to analyse the joint fabrication factors that affected the bonding strength, the parametric tests are conducted with various thickness of adhesive, surface roughness and fillet of adhesive. In addition, for the comparative study with the welded joint, lap-shear tests using specimens with 2 welded sides and 4 welded sides are also carried out. The quantitative results of the strength analysis are summarized, and some proposals are made on setting up testing standards for adhesively bonded joints.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.597-602
• /
• 2001

Most of the predicted shear strength of continuous R.C. beam whitout web reinforcement were accepted by testing simple beams. But the experimental results may show that a differential behavior on simple and continuous R.C. beam. In this study, estimated shear strength of continuous R.C. beam without web reinforcement with internal force state factors by test as purpose to apply available predicted equation to normal continuous R.C. beam. This equation is applied to experimentally tested data and the results were compared with those predicted by the codes. Predicted shear strength using force state factor can provide a tested data rather than codes which like ACI

• Structural Engineering and Mechanics
• /
• 제74권4호
• /
• pp.503-514
• /
• 2020

This study proposes prediction models for the shear strength of steel fiber reinforced concrete (SFRC) and ultra-high-performance fiber reinforced concrete (UHPC) beams using a Bayesian parameter estimation approach and a collected experimental database. Previous researchers had already proposed shear strength prediction models for SFRC and UHPC beams, but their performances were limited in terms of their prediction accuracies and the applicability to UHPC beams. Therefore, this study adopted a statistical approach based on a collected database to develop prediction models. In the database, 89 and 37 experimental data for SFRC and UHPC beams without stirrups were collected, respectively, and the proposed equations were developed using the Bayesian parameter estimation approach. The proposed models have a simplified form with important parameters, and in comparison to the existing prediction models, provide unbiased high prediction accuracy.

• Journal of Welding and Joining
• /
• 제8권2호
• /
• pp.70-79
• /
• 1990

Stainless clad steels were made through hot rolling process. Backing plates employed in this study were HSLA steel and mild steel. The shear bond strength increased with an increase of the soaking temperature and time. It was also found that the shear bond strength increased with an increase of the reduction ratio. The threshold deformation was observed to be 20% and 10% respectively when the soaking conditions of 15 min. at 900.deg. C and 30 min. at 1000.deg. C were applied. Either the rolling or the transverse direction did not give any significant difference in the shear bond strength. Stainless steel-HSLA steel was superior to stainless steel-mild steel in the same range of magnitude. Because the above experimental results were in contrary to the existing mechanisms, the new model was proposed to describe the bonding mechanism and the void formation.