• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.655-658
• /
• 2016

Xilinx 7-Series FPGA(Field Programmable Gate Array)s mainly used for the implementation of high-performance digital circuit have SRAM-type configuration memory and can malfunction when soft errors occur in their configuration memory. SEM(Soft Error Mitigation Controller) offered by Xilinx helps users mitigate the influence of soft errors in configuration memory. When soft errors occur, SEM Controller can recover the state of FPGA through partial reconfiguration if the soft errors are correctable by ECC(Error Correction Code) and CRC(Cyclic Redundancy Code). This paper presents the availability analysis of Xilinx 7-Series FPGAs against soft errors under the protection of the SEM Controller. Availability functions are derived and compared according to the correction capability of the SEM Controller. The result may help to estimate the reliability of SRAM-based FPGA running in an environment where soft errors may occur.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.3
• /
• pp.593-599
• /
• 2023

Nickel oxide (NiO) nanoparticles were successfully synthesized by a simple liquid phase process for producing ceramics powder using a precursor impregnated with a nickel(II) nitrate hexahydrate aqueous solution in an industrial pulp. The microfibrile structure of the precursor impregnated with nickel nitrate hexahydrate aqueous solution was confirmed by scanning electron microscope (SEM), and the crystal structure and particle size of nickel oxide (NiO) particles produced as the heat treatment temperature of the precursor were analyzed by X-ray diffraction (XRD) and SEM. As a result, it was confirmed through XRD and SEM analysis that the temperature at which the organic material of the precursor is completely thermally decomposed was 495-500℃, and the size and crystallinity of the nickel oxide particles produced increased as the heat treatment temperature increased. The size of the nickel oxide particles obtained by heat treatment at 500-800℃ for 1 hour was 50-200 nm. It was confirmed by XRD and SEM analysis that a NiO crystal phase was formed at a heat treatment temperature of 380℃, only a single NiO phase existed until 800℃.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.779-780
• /
• 2013

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2005.05a
• /
• pp.191-191
• /
• 2005

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2005.05a
• /
• pp.211-211
• /
• 2005

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.3
• /
• pp.100-107
• /
• 2011

To evaluate the wear characteristics of very thin ceramic coated layer, it is very important to investigate its wear process in great detail. An effective method for investigating the wear of a thin layer is the observation of wear process in microscopic detail, using in-situ system. In this study, based on the SEM Tribosystem as in-situ system, the microscopic wear mode of TiN coatings was investigated in repeated sliding. Consequently, four modes were revealed for TiN coatings: Ploughing, powder formation, flake formation and coating delimitation. Sc(Severity of contact) can clarify transition condition of those microscopic wear modes.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1271-1276
• /
• 2007

The most powerful analytical equipment usually comes at the cost of having the highest demand for space. Where electron microscopes has traditionally required a room to themselves, not just for reasons of their size but because of ancillary demands for pipes and service. The simple optical microscopes, of course, can occupy the desk-top, but because their performance is limited by the wavelength of light, their powers of magnification and resolution are inferior to that of the electron microscope. Mini SEM will sit comfortably on a desk-top but offers magnification and resolution performances much closer to that of a standard SEM. This new technique extends the scope of SEM as a high-resolution microscope, relatively cheap and widely available imaging tool, for a wider variety of samples.

• Tribology and Lubricants
• /
• v.23 no.4
• /
• pp.143-148
• /
• 2007

The surface defects of an aluminum tube for an OPC drum have been analyzed using a scanning microscopy(SEM) and an energy dispersive X-ray analyze.(EDX). The SEM/EDX system, which may provide good information on the surface defects and their distributions, provides an optical diameter of an impurity and a chemical composition. These are strongly related on the coated film thickness and quality of an OPC drum, which is a key element of a toner cartridge for a laser printer. The experimental results show that the local deformations, scratch wear, and flaws are produce the non-uniform coating layers, which may be removed by a manufacturing process of an aluminum tube. The major parameters on the coating quality of an OPC drum are the impurities of an aluminum tube such as silicon, oxygen, calcium, carbon, sulphur, chlorine, and others. These impurities may be removed by an ingot molding, extrusion and drawing, quality control, and packing processes with a strict manufacturing technology.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.323-323
• /
• 2010

PNN-PZT계 세라믹스를 $Pb(Ni_{1/3}Nb_{2/3})_{0.4}(Zr_{0.48}Ti_{0.52})_{0.6}O_3$ 조성으로 설계하고, 이에 낮은 융점의 NiO를 1wt% 첨가하여 저온소결 특성을 평가하였다. 일반적인 세라믹 분말 소결법을 이용하여 시편을 제작하였으며, 이때의 소결온도는 $850{\sim}105^{\circ}C$ 범위에서 변화시켰다. 소결체의 압전 및 유전적 특성을 평가를 하고. SEM 및 XRD를 이용한 미세구조 및 상 분석도 수행하였다. 이러한 실험 결과, PNN-PZT 세라믹은 NiO의 첨가로 $1000^{\circ}C$ 정도에서도 저온소결이 가능한 것을 확인하였다.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.5
• /
• pp.516-522
• /
• 2014

Old architectural wood materials damaged by a fire were evaluated on the basis of wood species and scanning electron microscopy (SEM) observation of wood tissues in combination with energy dispersive X-ray spectroscopy (EDXS) analysis. Results of SEM observation showed that tracheid wall thickness of burned parts was very thin compared with undamaged and sound wood, and tylosoid in the resin canals disappeared after the exposure to fire. SEM-EDXS analysis indicated that carbon and oxygen peaks occurred in the original energy band, and the carbon peak was higher than that of the oxygen in the burned part. A computerized tomography was also undertaken to investigate the carbonization layer formed by fire and possible internal defects.