• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.5
• /
• pp.102-107
• /
• 1999

In this paper hardened SCM440 material and annealed SCM440 material are for cutting experiments by the cutting con-dition which is chosen respectively by tool three components of cutting force are recorded using multicorder, Then the surface roughness for various force are measured by Roughness Tester. The results of the experiment are summarized as follow. The hardened material cut by ceramic tool(BX20) gives the highest radial component values among the cutting resistance radial components is increased higher for the higher cutting speed even though vertical component and axial component tend to decrease. But when the annealed material was cut increase in cutting speed results in the increase of three component forces. Since ceramic insert tip used the experiment hardly affect Built-up Edge and heat the cutting resistance decrease slightly regardless of the increased of cutting speed. The hardened material has higher three compo-nent force value than the annealed material because the material of high hardness is increased cutting resistance. The low-est cutting forces for hardened material and annealed material are shown in the cutting speed of 60m/min and 180m/min. respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.5
• /
• pp.712-720
• /
• 1998

The effect of H2:N2 gas ratio on the case thickness hardness and nitrides formation in the sur-face of SCM440 machine structural steel have been studied by micro-pulse plasma process. The thickness of compound layer increased with the increase of nitrogen content in the gas com-position. The maximum thickness of compound layer the maximum case depth and the maximum surface hardness were about 15.8${\mu}m$, 400${\mu}m$ and Hv765 respectively in the nitriding condition of 250Pa and 70% nitrogen content at $520^{\circ}C$ for 7hrs. Generally only nitride phases such as ${\'{\gamma}}$($Fe_4N$)$\varepsilon(Fe_2}{_3N}$ phases were detected in compound and diffusion layer by XRD analysis. The amount of $\varepsilon(Fe_2}{_3N}$ phase increased with the increase of nitrogen content. The relative amounts and kind of phases formed in the nitrided case changed with the change of nitrogen content in the gas composition.

• Journal of Surface Science and Engineering
• /
• v.31 no.5
• /
• pp.266-277
• /
• 1998

The effects of $H_2S$ gas ratio, temperature and time on the case depth, hardness, and sulfide and nitride formation on the surface of sulfnitrided SCM440 steel have been studied by micro-pulse plasma technique. The thickness of compound layer of sulfide and nitride increased with the increase of time, temperautre and $H_2S$ gas ratio. But surface hardness decreased with the increase of soft sulfide layer because the hard nitride layer formed beneath the sulfide. The thickness of sulfide layer was about 10$\mu\textrm{m}$ abpve 0.0088% of $H_2S$ gas. The highest surface hardness of the compound layer was Hv835 at $530^{\circ}C$, 1hr and 0.06% of $H_2S$ gas. X-ray diffraction indicated that the surface products were $Fe_{1_x}S$, $Fe_{2.5}N$ and $Fe_4N$. It was confirmed by EPMA that sulfide only existed in the surface.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.4
• /
• pp.39-45
• /
• 2010

Thick-walled cylinders, such as a cannon or nuclear reactor, are autofrettaged to induce advantageous residual stresses into pressure vessels and to increase operating pressure and the fatigue lifetimes. As the autofrettage level increases, the magnitude of compressive residual stress at the bore also increases. The purpose of the present paper is to predict the accurate residual stress of SCM440 high strength steel using the Kendall model which was adopted by ASME Code. Hydraulic pressure process was applied in the inner part and thick-walled cylinders were autofrettaged up to 30% overstrain levels. Electro polishing on the surface of autofrettage specimen was performed to get more accurate residual stress. Residual stresses were measured by X-ray diffraction method. The autofrettage surface which was plastically deformed analyzed using a scanning electron microscope(SEM). Although there were some differences in measured residual stress and numerical results, it has a tendency to agree comparatively with each other.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.1-7
• /
• 2017

This study investigates the high-frequency heat treatment characteristics with the distance between a coil and SCM440 parts for an automobile. Global automobile makers are focusing on research to develop high-performance automobiles with improved fuel efficiency and lower emissions in accordance with consumer demand and environmental policies. However, most research on high-frequency heat treatment has been experimental, and it is very difficult to obtain high-frequency heat treatment conditions for a specific product. Therefore, all the conditions of high-frequency heat treatment except the distance between a coil and SCM440 parts were kept the same. As a result, the optimized distance between the coil and SCM440 parts was observed to be 1-2 mm. When the distance between the coil and SCM440 parts was over 3 mm, the effective case hardness depth and total case hardness depth did not satisfy the standards.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.131-132
• /
• 2011

저압가스질화법을 이용하여 SCM440강을 신속질화처리 하였다. 기존의 가스질화법과는 달리 낮은 암모니아가스 농도의 분위기와 아산화질소를 사용한 산화반응의 영향으로 5시간의 짧은 질화처리로서 0.6mm 이상의 질화깊이를 확보할 수 있었다.

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.3
• /
• pp.54-62
• /
• 1991

The effect of tempering temperature on the ultrasonic propagation velocity at SCM 440 steel quenched from $870^{\circ}C$ and $1000^{\circ}C$ has been studied by metallurgical and crystallographical observation. The measurements of ultrasonic velocity were made on the specimen by appling an immersion ultrasonic pulse-echo technique with a constant frequency of 10 MHz. The quenched microstructure of this steel was a lath martensite. As the tempering temperature was increased, the martensite was transformed into the tempered martensite composed of cementite and carbide. The ultrasonic velocity increased with increasing the tempering temperature. It was thought that these were resulted from the microstructural transformation. The change of ultrasonic propagation velocity with quenching and tempering heat treatment was resulted from microstrain due to the change of internal stress. Considering these results concerning to the change of ultrasonic propagation velocity. the phenomena of microstructural transformation were estimated. Consequently, it was thought that the degree of quenching and tempered heat treatment of steel could be nondestructively evaluated with the change of ultrasonic propagation velocity.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.4_2
• /
• pp.571-576
• /
• 2023

In this study, the harmless crack size(a_hml) according to the residual stress depth was evaluated using the fatigue limit of SCM440 steel by quenching-tempering(QT) and induction hardening(IH), and threshold stress intensity factor of QT steel. Because the residual stress increased rapidly as the crack depth increased, a_hml was determined at the depth of all the crack aspect ratio(As) regardless of Type I-III, and a_hml also increased according to the residual stress depth. a_hml was minimal at As=1.0 and maximal at As=0.1, but was almost similar on each Type. a_hml was small the dependence on As.

• Journal of Surface Science and Engineering
• /
• v.43 no.2
• /
• pp.91-96
• /
• 2010

SCM440 steels were nitrided using pulsed dc plasma combined with inductively coupled plasma (ICP) generated by 13.56 MHz rf power in order to enhance case hardening depth. The case hardening depth was increased with rf power. The effective case-depth with ICP at 900 watt was as 1.6 times as that nitrided without ICP. The hardening depth was also increased up to 1.45 times. The compound layers formed on top surface were dense and thin when pulsed dc plasma was combined with ICP.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.1
• /
• pp.74-80
• /
• 2016

Due to the increased use of power caused by industrial development, the importance of improving wear and friction in the contact region has emerged. Except for some parts, such as brakes or clutches and friction, seals and precision mechanical parts (e.g., pistons, bearings, valves, and cams) are important engine components that require low friction characteristics. In this study, the experimental method used to determine the friction characteristics was based on the type of rpm with the pin-on-disc test device, the element analysis program ANSYS was used to analyze the surfaces of the two metals rubbing together, and physical formation FEM models were used to study the properties and wear. The friction coefficient of variation was unsafe, but at the start of wear, it converged to a stable friction coefficient that increased after a certain slip away.