• Journal of the Korean Wood Science and Technology
• /
• v.34 no.2
• /
• pp.10-21
• /
• 2006

Recycled polypropylene (RPP) - Wood Saw Dust (WSD) composites with and without acetylation of filler were produced at different filler loading (15%, 25%, 35% and 45% w/w) and filler size (300, 212 and $100{\mu}m$). The RPP-WSD was compounded using a Haake Rheodrive 500 twin screw compounder at $190^{\circ}C$ at 8 MPa for 30 minutes. The mechanical properties and water absorption properties of modified and unmodified WSD-PP composites were investigated. Acetylation of WSD improved the mechanical and water absorption characteristic of composites. The decrease of filler size (300 to $100{\mu}m$) of the unmodified and acetylated WSD showed increase of tensile strength and impact properties. The composites exhibited higher tensile modulus properties as the filler loading increased (15% to 45%). However tensile strength, elongation at break and impact strength showed the opposite phenomenon. Water absorption increased as the mesh number and filler loading increased. With acetylation, lower moisture absorption was observed as compared to unmodified WSD. The failure mechanism from impact fracture of the filler-matrix interface with and without acetylation was analyzed using Scanning Electron Microscope (SEM).

• Journal of Sensor Science and Technology
• /
• v.16 no.4
• /
• pp.301-306
• /
• 2007

AlN thin film for SAW filter application was deposited on (100) silicon wafers by reactive magnetron sputtering method. The structural characteristics were dependent on the deposition conditions such as sputtering pressure, RF power, substrate temperature, and nitrogen partial pressure. Scanning Electron Microscope (SEM), X-ray Diffraction (XRD), Electron Probe MicroAnalyzer (EPMA) and Atomic Force Microscope (AFM) have been used to find out structural properties and preferred orientation of AlN thin films. Insertion loss of SAW devices was 28.51 dB and out of band rejection was about 24 dB.

• Electrical & Electronic Materials
• /
• v.10 no.1
• /
• pp.1-7
• /
• 1997

SAW filter has been used in mobile communication device, bandpass filter and resonator for merits )f miniaturization and high reliability. Materials for substrate mainly used single crystal such as LiNbO$_{3}$, LiTaO$_{3}$, ZnO. In this study, it was attempted that LiNbO$_{3}$ was substituted for piezoelectric ceramics(PZT4, PZT5A and PZT8) which had simple fabrication process because fabrication of crystal is difficult and it's cost is high. SAW filters were fabricated by the photolithography on piezoelectric ceramics substrates in order to compare their characteristics with LiNbO$_{3}$'s. The experimental value of center frequency was compared with theoretical one. The average difference of center frequency was 3.7%. PZT8 showed the best bandwidth properties among them. It is considered that PZT8 has higher mechanical quality factor and propagation velocity than others.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.237.2-237.2
• /
• 2011

SAW-ED를 이용하는 박막공정 기술을 통하여 나노레벨의 SWCNT 와 PEDOT의 thin film 및 hybrid화된 film구조를 얻을 수 있었다. SWCNT와 전도성고분자와의 hybridization을 통해 균일상의 표면 morphology를 갖는 고전도성 투명 필름을 제작하고, 이들의 전기광학적 성질을 확인하였다. SAW-ED를 이용하는 박막공정 기술은 나노입자 및 나노구조물의 박막화 패턴화를 포함하는 새로운 deposition 기술로서의 응용성을 가지고 있으며, 본 연구에서는 SWCNT와 전도성고분자를 이용하여 이를 확인하였다.

• Proceedings of the KWS Conference
• /
• 1998.05a
• /
• pp.112-114
• /
• 1998

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.3
• /
• pp.88-93
• /
• 2021

SAW (Submerged Arc Welding) is often used for ship construction or welding pressure vessels and involves spraying a flux in a powder form to a welding site to a certain thickness and continuously supplying electrode wires therein. This welding method enables high current welding up to 1,500 to 3,000 A. Arc efficiency is higher than 95% and the technique allows clean work as it creates less welding fume, which is composed of fine metal oxide particles, and the arc beam is not exposed. In this study, SM490C-TMC thick plates were heterogeneously welded by SAW. Mechanical properties of welds were measured, and welds were assessed macroscopically and for adhering magnetic particles. The following conclusions were drawn. Bending tests showed no spots exploded on sample surfaces or any other defect, and plastic deformation testing confirmed sufficient weld toughness. These results showed the 1F welding method has no shortcomings in terms of bending performance.

• Journal of the Korean Ceramic Society
• /
• v.40 no.6
• /
• pp.547-552
• /
• 2003

ZnO thin films on glass substrate were deposited by RF magnetron reactive sputtering at 100 W, 1.33 Pa, Ar/O2=50 : 50, 200$^{\circ}C$, and a target/substrate distance of 4 cm. Crystallinities, surface morphologies, chemical compositions, and electrical properties of the films were investigated by XRD, SEM, AFM, RBS, and electrometer. All films showed a strong preferred c-axis orientation and the chemical stoichiometry. The propagation velocity of ZnO/IDT/glass of single electrode and double electrode types SAW filter was about 2,589 m/sec, 2,533 m/sec and insertion loss was a minimum value of about -11 dB and -21 dB, respectively.

• Korean Journal of Materials Research
• /
• v.5 no.6
• /
• pp.650-656
• /
• 1995

High frequency SAW filters for cellular communications were fabricated by metallizing 36$^{\circ}$Y-X LiTaO$_3$piezoelectric substrate with IIDT type electrodes. It was found that the center frequency of the filter was lowered than as designed. In order to overcome such a drawback and enable a fine tuning of its center frequency, dielectric SiN$_{x}$ thin films were deposited on LiTaO$_3$substrate by PECVD as passivation layer and then frequency responses were also characterized. As a result, the center frequency of the filter could be shifted to a higher frequency with increasing the thickness of SiN$_{x}$ film, because SAW velocity increased with increasing the ratio of the thickness of dielectric thin film to wavelength. The insertion loss of the filter, however, became larger with increasing the thickness of SiN$_{x}$ film.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.6
• /
• pp.481-486
• /
• 2001

ZnO thin films on glass substrate were depostied by RF magnetron reactive sputter with various argon/oxygen gas ratios and substrate temperatures. Crystallinities, surface morphologies, chemical compositions, and electrical properties of the films were investigated by XRD, SEM, XPS and electrometer(keithley 617). All films showed a strong preferred orientation along the c-axis on glass substrate, and the chemical stoichiometry was obtained at Ar/O$_2$.=50/50. The propagation velocity of ZnO SAW filter was about 2,590 m/sec and insertion loss was a minimum value of abut -21dB.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1479-1481
• /
• 2002

AlN thin films were deposited on Si(100) and $SiO_2$/Si substrates using R.F. magnetron sputtering system. The effect of various deposition conditions on the crystal orientation of AlN films was investigated to obtain a highly (002)-oriented films. SAW filters were fabricated using AlN films with various thicknesses and their frequency response characterizations were measured. Experimental results showed that the (002)-orientation and surface roughness of AlN films played a crucial role of determining the frequency response of AlN SAW devices.