• Proceedings of the Optical Society of Korea Conference
• /
• 2001.02a
• /
• pp.152-153
• /
• 2001

파장 가변형 광 필터와 파장 선택형 광 스위치는 파장분할다중 광통신 및 광 교환 시스템을 구현하는데 매우 중요한 소자들 중의 하나이다. 특히 음향광학효과를 이용한 파장 가변형 광 필터(AOTF ： Acousto-Optic Tunable Filter)는 150nm 이상의 넓은 파장 가변범위, 1.5nm이하의 좁은 통과대역폭, 수 $\mu\textrm{s}$ 정도의 비교적 빠른 스위칭 속도 그리고 여러 개의 파장 채널을 동시에 선택할 수 있는 장점들을 가지고 있지만, 한편으로 표면 음향파(SAW： Surface Acoustic Wave) 구동에 필요한 RF 파워와 부 모드 (sidelobe)가 비교적 크다는 단점 때문에 실용화에 많은 제약을 받아왔다. (중략)

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.3
• /
• pp.678-684
• /
• 2013

This paper describes a low-power baseband circuit for SAW-less LTE-Advanced transmitters. The proposed transmitter baseband circuit consists of a 2nd-order Tow-Thomas type active RC-LPF and a 1st-order passive RC LPF. It can provide a 7 multi-channel cut-off frequencies and wide gain control range of -41 dB ~ 0 dB with a 1-dB step. The proposed 2nd-order active RC-LPF adopts an op-amp in which three other sub-op amps are in parallel connected to reduce DC current for different cutoff frequency. In addition, each sub-op amp adopts both Miller and feed-forward phase compensation method to achieve an UGBW of more than 1-GHz with a small DC power consumption. The proposed baseband circuit is implemented in 65-nm CMOS technology, consuming DC power from 6.3 mW to 24.1 mW from a 1.2V supply voltage for each different cut-off frequency.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.3
• /
• pp.1-9
• /
• 2003

In this paper, we designed a highly suppressed sidelobe ladder type RF SAW bandpass filter based on 1-port resonator, for 800 MHz mobile communication system. In order to get the highest device characteristics, we optimized some important parameters such as the electrode thickness, electrode lambda weghting of the reflectors, and static capacitance ratio. Furthermore, we fabricated the Tx and Rx. filter using optimized parameters. Implemented filters can be used in 800 MHz mobile communication system and external impedance matching circuits are not needed. RF filter was fabricated on 36$^{\circ}$LiTaO$_3$ substrates with Al-Cu (W 3 %)and mounted 3.8mm$\times$3.8mm$\times$1.5mm SMD package. Developed filters has 2.3 dB insertion loss in the 25 MHz pass-band, 33MHz with 3-dB insertion loss, stop-band rejection of 30 dB, passband ripple is less than 0.5 The power durability of the filters measured about 3.5W and the maximum temperature variation within -2$0^{\circ}C$~8$0^{\circ}C$ was 0.09 dB/$^{\circ}C$ of 3-dB insertion loss.

• The Journal of the Acoustical Society of Korea
• /
• v.19 no.2
• /
• pp.33-39
• /
• 2000

We have studied to obtain the frequency characteristics of the Surface Acoustic Wave(SAW) bandpass filter, having low shape factor, it's interdigital transducer(IDT) was formed on the 35° Y-cut X-propagation Quartz substrate and was evaporated by Aluminium. And then, we performed computer-simulation by a simulator. And, we can design that the apodization weighted type IDT as an input transducer of the filter and the withdrawal weighted type IDT as an output transducer of the filter from the results of our computer-simulation. Also, we have employed that the number of pairs of the input and output IDT are 2200 pairs and 1000pairs, respectively and used the Kaiser-Bessel window function in order to minimize the effect of ripple. And, while the width and the space of IDT's finger are 6㎛ m and 5.75㎛, respectively and we could obtain the resonable results when the IDT thickness was 6000Å in consideration of the ratio of SAW's wavelength, and IDT aperture is 2mm. Frequency response of the fabricated SAW bandpass filter has the property that the center frequency is about 70MHz, shape factor is less than 1.3, bandwidth at the 1.5dB is probably 1.3MHz, out-band attenuation is almost -45dB, insertion loss is 19dB and ripple in the width of bandpass is 1dB approximately. Therefore, these frequency characteristics of the fabricated SAW bandpass filter are agreed well with the designed values.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.12
• /
• pp.979-983
• /
• 2012

We proposed the ZnO thin film for a SAW filter by PLD and RF sputtering method. ZnO thin films was pre-deposited on a sapphire substrate as a seed layer by PLD method and then deposited on seed layer by RF sputtering. The surface characteristics of ZnO thin film were investigated by XRD, SEM and AFM. The minimum surface roughness was 1.92 nm and FWHM of rocking curve was $0.92^{\circ}$. We demonstrated the SAW filter with bandwidth of approximately 0.97 MHz and the center frequency of 18.72 MHz using the proposed ZnO thin film.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.4
• /
• pp.32-39
• /
• 1998

Remez exchange algorithm was applied to realize an IF SAW filter for CDMA cellular phone systems. A SAW filter with withdrawal weighted transducers was simulated and then fabricated on 42.75.deg. ST-cut Quaritz wafer. Excellent agreement wasobtained between calculated andmeasured responses. Fabricated SAWfilterswere mounted on ceramic SMD package for reducing their size and volume. SAW filters were measured under matched circuit. As a result, 5 dB bandwidth of 1.32 MHz, 33dB bandwidth of 1.76 MHz, insertion loss of 13.8 dB and peak to peak ripple at passband of 0.26 dB were obtained. Linear group delay responses at passband were also obtained. These characteristics were good for practical use of IF SAW filter for CDMA system.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.597-598
• /
• 2006

This paper describes a development of a new $1.4{\times}1.1$ and $2.0{\times}1.4mm$ RF SAW filters made by PCB substrate instead of HTCC package, and this technology can reduce the cost of materials down to 40%. We have investigated the multi-layered PCB substrate structures and raw materials to find out the optimal flip-bonding condition between the $LiTaO_3$ wafer and PCB substrates. Also the optimal materials and processing conditions of epoxy laminating film were found out through the experiments which can reduce the bending moment caused by the difference of the thermal expansion between the PCB substrate and laminating film. The new PCB SAW filter shows good electrical and reliability performances with respect to the present SAW filters.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1992.06a
• /
• pp.578-583
• /
• 1992

• Proceedings of the Korean Vacuum Society Conference
• /
• 1994.02a
• /
• pp.37-37
• /
• 1994

• Journal of Korean Electronics
• /
• v.24 no.7
• /
• pp.62-63
• /
• 2004