• Journal of Ocean Engineering and Technology
• /
• v.1 no.2
• /
• pp.123-129
• /
• 1987

Corrosion fatigue fracture of dual phase steel(SS41) and raw material steel(SS41) were investigated in 3.5% NaCl aqueous solution at PH 4,6,9 and 11. The fatigue limit of dual phase steel is increased approximately 1.8 times larger than that of raw material in air. The corrosion fatigue life of dual phase steel is about 5-10 times larger than that of raw material in 3.5% NaCl aqueous solution. The reduction of fatigue life is larger for the acidsalt solution than for the alkali salt solution. The reduction of stress level on the reduction ratio of corrosion fatigue life is large as pH 6-11. The reduction ratio of corrosion fatigue life of dual phase steel and raw material is nearly coincided at pH 2. While at pH4-2 the reduction ratio of corrosion fatigue life only depends on the corrosion effect. It has been found that the corrosion resistance effect of dual phase steel is smaller than that of raw material in corrosion fatigue crack propagation rate. As pH below 6 is changed, it can be clearly observed from raw material that the brittle intergranular fracture is characterized, and from the above result, the influence of corrosion of dual phase steel is small.

• Journal of the Korea Concrete Institute
• /
• v.18 no.1 s.91
• /
• pp.57-64
• /
• 2006

The crack presented in concrete structures causes a structural defect, the durability decrease, and external damages etc. Therefore, it is necessary to improve durability through the effort to control the crack. Fluosilicic acid($H_2SiF_6$) is recovered as aqueous solution which absorbs $SiF_4$ produced from the manufacturing of industrial-graded $H_3PO_4$ or HF. Generally, fluosilicates prepared by the reaction between $H_2SiF_6$ and metal salts. Addition of fluosilicates to cement endows odd properties through unique chemical reaction with the fresh and hardened cement. Mix proportions for experiment were modulated at 0.45 of water to cement ratio and $0.0{\sim}2.0%$ of adding ratio of fluosilicate salt based inorganic compound. To evaluate correlation of concrete strength and adding ratio of fluosilicate salt based inorganic compound, the tests were performed about design strength(21, 24, 27 MPa) with 0.5% of adding ratio of fluosilicate salt based inorganic compound. Applications of fluosilicate salt based inorganic compound to reduce cracks resulted from plastic and drying shrinkage, to improve durability are presented in this paper. Durability was evaluated as neutralization, chloride ion penetration depth, freezing thawing resistant tests and weight loss according reinforcement corrosion. It is ascertained that the concrete added fluosilicate salt based inorganic compound showed m ability to reduce the total area and maximum crack width significantly as compared non-added concrete. In addition, the durability of concrete improved because of resistance to crack and watertightness by packing role of fluosilicate salt based inorganic compound obtained and pozzolanic reaction of soluble $SiO_2$ than non-added concrete.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.43 no.7
• /
• pp.1048-1054
• /
• 2014

The purpose of this study was carried out to investigate the cause of sulfur dioxide occurrence, general element composition, sulfur compounds, heavy metals, macro- & micro-minerals, and oxidation-reduction potential (ORP) following baking time course of RS (RS1, RS2, RS3, and RS4) and mudflat solar salts (MSS). Sulfur dioxide ($SO_2$) and sulfite ($SO{_3}^{2-}$) were not detected in MSS or RS. However, sulfate ($SO{_4}^{2-}$) content significantly decreased in RS (29,878.15~36,097.45 ppm) compared to that in MSS (35,601.65 ppm). ORP was 181.15 mV in MSS, and 58.55 mV in RS1. Moisture content was 9.34% in MSS and 0.00% in RS with increased NaCl (94.77~95.77%). Moisture and NaCl contents showed no significant difference in RS. Insoluble and sandy residues were higher in RS than in MSS, whereas Ca and K showed no significant difference. Mg and Cl contents were higher in RS than in MSS. Br level was higher in MSS (628.1 ppm) than in RS (512.72~586.62 ppm), but there was no significant difference in $NO_3$. Heavy metals (Pb, As, and Hg) were more abundant in RS than in MSS, but levels were still safe. These results suggest that MSS and RS may increase protection against from $SO_2$ and $SO{_3}^{2-}$.

• The Korean Journal of Ecology
• /
• v.26 no.3
• /
• pp.135-142
• /
• 2003

Four legume plants showed better growth by the external nitrogen supply rather than the symbiotic nitrogen fixation only under salt additions. In case of Glycine max and Phaseolus angularis, total nitrogen contents decreased by high salinity level but their amino acid levels significantly increased with the increase of salt treatments and indicated high soluble-/insoluble-N ratios. Cassia tora and Albizzia julibrissin contained less amino acids than G. max and P. angularis but total N (esp. insoluble N fraction) increased with higher salt levels. Asparagine occurred as a main amino acid especially in G. max and P. angularis and can be seen as potential N-storage form in these plants. It might be play an important role for the osmoregulation mechanism under the saline condition. Meanwhile, to investigate what kinds of nitrogen sources are effective for overcoming salt stress on soybean plants, various N forms and concentrations (NH₄NO₃-N, NO₃-N, NH₄NO₃-N; 2.5 and 5 mM) were additionally supplied to the salt gradient medium. Soybean plants treated with NH₄NO₃-N showed the best growth up to 40 mM NaCl and NO₃- fed plants indicated good growth even at 80 mM NaCl treatments. Contrary to NH₄NO₃- and NO₃- fed plants, NH₄/sup +/- fed plants showed remarkable growth reduction and died by 40 and 80 mM NaCl treatments after the first harvest (15th day). Consequently, these results suggest that salt excluding and resistant capacities of soybean plants under NaCl treatments are increased in order of NH₄ - N, control, NO₃- N and NH₄NO₃- N depending on N concentration except NH₄- N treatments.

• Journal of Radiation Industry
• /
• v.5 no.3
• /
• pp.211-220
• /
• 2011

This study was carried out to develop salt tolerant varities of rapeseed (Brassica napus L.) which can be grown in the high salty reclaimed land. The seeds of three varieties 'Naehan', 'Tammi', and 'Halla' were treated by proton ion beams and gamma rays with 0 to 2,000 Gy. For the selection of salt tolerant lines, emergence and survival rate, and growth characteristics of $M_2$ to $M_4$ generations were investigated in the Saemangeum reclaimed fields with the different salt concentrations. The lines with potential salt tolerance were selected in the $M_4$ generation and tested indoor for their growth characteristics. There was no significant changes in the soil pH for $M_4$ generation during growth period. However, soil EC was higher in early spring than sowing period (mid October). In $M_4$ generation test, the seeds of original and selected line showed high rates of emergence and survival, as determined one month after sowing. After wintering, however, the original varieties showed the significant reduction in the survival rate, while the selected lines showed a higher survival rate and good growth, leading to the completion of their life cycle. Consequently we selected 9 lines from $M_4$ generation with better performance in growth and yield. Soil EC was $2.8{\sim}4.3dS{\cdot}m^{-1}$ during $M_4$ generation growth period. The laboratory test of the lines selected from $M_4$ generation was made for their salt tolerance potential. The selected lines showed higher chlorophyll and proline contents than the original varieties. There was also no significant difference in the emergence rate of seed between the original and selected varieties. In 200 mM natural sea salt, the $N{\gamma}600-21-1-641$ line derived from 'Naehan' was the highest in growth rate, leaf chlorophyll and proline contents. $T{\gamma}800-20-2-461$ line derived from 'Tammi' didn't show significant difference in growth rate compared to original variety in 200 mM and withered in 250 mM like other lines as time passed. $H{\gamma}200-7-1-740$ line showed similar growth and chlorophyll content compared to its original variety.

• Journal of Marine Life Science
• /
• v.6 no.2
• /
• pp.80-87
• /
• 2021

In this study, the toxic effects of PFOA and PFOS potassium salt on Mesocentrotus nudus using 10 min-fertilization rate and 48 h-normal embryogenesis were confirmed through the calculation of toxicity values such as Non-observed effective concentration, Low-observed effective concentration, and 50% of effective concentration. The case of 10 min-fertilization rate and 48 h-normal embryogenesis showed the concentration-dependent reduction pattern when exposed to PFOA and PFOS potassium salt, in tested concentration, respectively. The EC50 values of 10 min-fertilization rates for PFOA and PFOS potassium salt were 1346.43 mg/l and 536.18 mg/l, respectively, and the EC50 values of 48 h-normal embryogenesis were 42.67 mg/l and 17.81 mg/l, respectively. Both toxicity test methods showed high toxicity sensitivity to PFOS potassium salt. Recent studies have shown that the concentration of PFOA and PFOS in the marine environment has continuously decreased, and it is not enough to show acute toxicity to sea urchin. However, PFOA and PFOS have a very long half-life and can accumulate throughout the life of marine life, so it is still observed at a high concentration in shellfish. Therefore, a study on chronic toxicity through the whole-life cycle of marine organisms in coastal environments should be needed.

• The Korean Journal of Food And Nutrition
• /
• v.11 no.4
• /
• pp.444-451
• /
• 1998

The changes of amine, nitrate and nitrite nitrogen in yellow corvenia were studied during its processing and storage in order to clarify the precursors of N-nitrosamine(NA) formation in the salted and dried yellow corvenia(Gulbi), prepared y using the different salting method like dry and brine salting by pure and curde salt. As a result, during the processing and storage of Gulbi, DMA and TMA contents were significantly increased in the yellow corvenia. And after 40 days storage the increase rate showed 25.7∼45.7, 3.3∼5.6 times higher than those of 0.3, 2.4mg/kg, respectively, while nitrite contents, during its processing and storage, were scarcely changed in the salted and dried yellow corvenia. During the processing and storage, of Gulbi, DMA and TMA contents were less produced in brine salted and dried yellow corvenia using crude salt than in sample prepared using were scarcely changed in the salted and dried yellow corvenia. During the processing and storage of Gulbi, DMA and TMA contents were less produced in brine salted and dried yellow corvenia using crude salt than in sample prepared using pure salt, while the former were more effective than the latter in inhibiting the production of nitrate and nitrite. Therefore, it was revealed that reduction of NA precursors such as DMA, TMA, nitrate and nitrite were more effective in preparing with the brine salting method than with the dry salting method.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.4
• /
• pp.965-972
• /
• 2015

Along with the rapid development in digital times, image media are being used in internet, computer and digital camera. But image deterioration occurs due to various exterior reasons in the procedures of acquisition, processing, transmission and recording of digital image and major reason is noise. Therefore in order to remove salt & pepper noise, this study suggested the algorithm which replaces the noise to original pixel in case of non-noise, and processes the noise with Lagrange interpolation method in case of noise. In case high density noise was added and the noise could not be removed, noise characteristics were improved by processing the noises repeatedly. And for objective judgment, this method was compared with existing methods and PSNR(peak signal to noise ratio) was used as judgment standard.

• Korean Journal of Materials Research
• /
• v.16 no.9
• /
• pp.557-563
• /
• 2006

The electrolytic reduction of spent oxide fuel involves the liberation of oxygen in a molten LiCl electrolyte, which results in a chemically aggressive environment that is too corrosive for typical structural materials. So, it is essential to choose the optimum material for the process equipment handling molten salt. In this study, corrosion behavior of Inconel 713LC, MA 754, X-750 and 718 in the molten salt $LiCl-Li_2O$ under an oxidizing atmosphere was investigated at $650^{\circ}C$ for $72{\sim}216$ hours. Inconel 713LC alloy showed the highest corrosion resistance among the examined alloys. Corrosion products of Inconel 713LC were $Cr_2O_3,\;NiCr_2O_4$ and NiO, and those of Inconel MA 754 were $Cr_2O_3\;and\;Li_2Ni_8O_{10}$ while $Cr_2O_3,\;NiFe_2O_4\;and\;CrNbO_4$ were produced from Inconel 718. Also, corrosion products of Inconel X-750 were found to be $Cr_2O_3,\;NiFe_2O_4\;and\;(Cr,Nb,Ti)O_2$. Inconel 713LC showed local corrosion behavior and Inconel MA 754, 718, X-750 showed uniform corrosion behavior.

• Journal of Microbiology and Biotechnology
• /
• v.20 no.11
• /
• pp.1577-1584
• /
• 2010

In total, 140 halotolerant bacterial strains were isolated from both the soil of barren fields and the rhizosphere of six naturally growing halophytic plants in the vicinity of the Yellow Sea, near the city of Incheon in the Republic of Korea. All of these strains were characterized for multiple plant growth promoting traits, such as the production of indole acetic acid (IAA), nitrogen fixation, phosphorus (P) and zinc (Zn) solubilization, thiosulfate ($S_2O_3$) oxidation, the production of ammonia ($NH_3$), and the production of extracellular hydrolytic enzymes such as protease, chitinase, pectinase, cellulase, and lipase under in vitro conditions. From the original 140 strains tested, on the basis of the latter tests for plant growth promotional activity, 36 were selected for further examination. These 36 halotolerant bacterial strains were then tested for 1-aminocyclopropane-1-carboxylic acid (ACC) deaminase activity. Twenty-five of these were found to be positive, and to be exhibiting significantly varying levels of activity. 16S rRNA gene sequencing analyses of the 36 halotolerant strains showed that they belong to 10 different bacterial genera: Bacillus, Brevibacterium, Planococcus, Zhihengliuella, Halomonas, Exiguobacterium, Oceanimonas, Corynebacterium, Arthrobacter, and Micrococcus. Inoculation of the 14 halotolerant bacterial strains to ameliorate salt stress (150 mM NaCl) in canola plants produced an increase in root length of between 5.2% and 47.8%, and dry weight of between 16.2% and 43%, in comparison with the uninoculated positive controls. In particular, three of the bacteria, Brevibacterium epidermidis RS15, Micrococcus yunnanensis RS222, and Bacillus aryabhattai RS341, all showed more than 40% increase in root elongation and dry weight when compared with uninoculated salt-stressed canola seedlings. These results indicate that certain halotolerant bacteria, isolated from coastal soils, have a real potential to enhance plant growth under saline stress, through the reduction of ethylene production via ACC deaminase activity.