• Journal of Radiation Protection and Research
• /
• v.28 no.2
• /
• pp.87-95
• /
• 2003

The fabrication process and the structure of PIN semiconductor detectors have been designed optimally by simulation for doping concentration and width of p+ layer, impurities re-contribution due to annealing and the current distribution due to guard ring at the sliced edges. The characteristics to radiation response has been also simulated in terms of Monte Carlo Method. The device has been fabricated on n type, $400\;{\Omega}cm$, orientation <100>, Floating-Zone silicon wafer using the simulation results. The leakage current density of $0.7nA/cm^2/100{\mu}m$ is achieved by this process. The good linearity of radiation response to Cs-137 was kept within the exposure ranges between 5 mR/h and 25 R/h. This proposed process could be applied for fabricating a PIN semiconductor detector for measuring individual dose.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.230-232
• /
• 2019

Light Triggerd Thyristor (LTT)는 HVDC 및 산업용 스위치 등에 사용되는 대전력 반도체소자이다. 일반적인 Thyristor가 전기적 신호에 의해 trigger 되는 것과는 다르게 LTT는 광신호에 의해 동작하는 소자이다. 본 논문에서는 5,000V, 2,200A 급의 4인치 LTT 소자의 제작 및 전기적인 특성평가 결과를 기술하였다. 4인치 LTT의 구조적인 특징은 전면부 중앙에 광신호가 주입되는 수광부가 위치해 있으며 입력 전류 증폭을 위한 4-단계 증폭 게이트 (gate) 구조를 가지도록 설계하였다. $400{\Omega}{\cdot}cm$ 비저항을 갖는 1mm 두께의 n-형 실리콘 웨이퍼에 boron 이온주입과 열처리 공정으로 약 $30{\mu}m$ 깊이의 p-base를 형성하였으며, 고내압 저지를 위한 edge termination은 VLD (variable lateral doping) 기술을 적용하였다. 제작된 4인치 LTT는 6,500 V의 순방향 항복전압 ($V_{DRM}$) 특성을 나타내었으며, 100V의 어노드전압 ($V_A$)과 20 mA의 게이트전류 ($I_G$)에 의하여 thyristor가 trigger 됨을 확인하였다. 제작한 LTT 소자는 disk형 press-pack 패키지를 진행한 후, LTT의 수광부에 $10{\mu}s$, 50 mW의 900 nm 광 펄스를 조사하여 전류 특성을 평가하였다. LTT 패키지 샘플에 60 Hz 주파수의 광 펄스를 조사한 경우 2,460 A의 순방향 평균전류 ($I_T$)와 $336A/{\mu}s$의 반복전류상승기울기 (repetitive di/dt)에 안정적으로 동작함을 확인하였다. 또한, 펄스 전류 시험의 경우 61.6 kA의 최대 통전 전류 (ITSM, surge current)와 $1,050A/{\mu}s$의 펄스전류 상승 기울기 (di/dt of on-state pulse current)에도 LTT의 손상 없이 동작함을 확인하였다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.5
• /
• pp.204-209
• /
• 2007

We synthesized a series of $CaS_{1-x}Se_x:Eu$ red-emitting phosphors for application in phosphor-converted three-band white light emitting diode(LED). The photoluminescence and structural properties of $CaS_{1-x}Se_x:Eu$ were examined. The $CaS_{1-x}Se_x:Eu$ phosphors have a strong absorption at 455 nm, which is the emission wavelength of a blue LED. CaS:Eu has a red omission peak at 651 nm due to the $4f^65d^1(T_{2g}){\rightarrow}4f^7(^8S_{7/2})$ transition of the $Eu^{2+}$. The emission peak of $CaS_{1-x}Se_x:Eu$ is shifted from 651 to 598 nm with increasing Se content. $CaS_{1-x}Se_x:Eu$ can be used as wavelength-tunable red-emitting phosphors pumped by a blue LED. We also fabricated a three-band white LED by doping $SrGa_2S_4:Eu$ and $CaS_{0.50}Se_{0.50}:Eu$ phosphors onto a blue LED chip.

• Journal of the Korean Electrochemical Society
• /
• v.14 no.4
• /
• pp.208-213
• /
• 2011

Solid polymer electrolytes using $BF_3LiMA$ as monomer were synthesized by usual one step radical polymerization in THF solvent. The effect of $BF_3LiMA$ concentration on ionic conductivity and electrochemical stability was investigated by AC impedance measurement and linear sweep voltammetry. As a result, the highest ionic conductivity reached $7.71{\times}10^{-6}S\;cm^{-1}$ at $25^{\circ}C$ was obtained in 12.9 wt% of $BF_3LiMA$ content. Further increase or decrease of $BF_3LiMA$ content result to decrease the ionic conductivity due to the brittle matrix properties in former case and the insufficient number of charge carrier in the latter case. Furthermore, since the counter-anion was immobilized in the self-doped solid polymer electrolytes, high electrochemical stability up to 6.0 V was observed even in $60^{\circ}C$.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.10
• /
• pp.3407-3412
• /
• 2012

The Ti incorporation at Fe-site in the double perovskite lattice of $Sr_2FeNbO_6$ (SFNO) system is studied. The Ti concentration optimization yielded an efficient photocatalyst. At an optimum composition of Ti as x = 0.07 in $Sr_2Fe_{1-x}Ti_xNbO_6$, the photocatalyst exhibited 2 times the quantum yield for photolysis of $H_2O$ in presence of $CH_3OH$, than its undoped counterpart under visible light (${\lambda}{\geq}420nm$). Heavily Ti-doped $Sr_2Fe_{1-x}Ti_xNbO_6$ lattice exhibited poor photochemical properties due to the existence of constituent impurity phases as observed in the structural characterization, as well as deteriorated optical absorption. The higher electron-density acquired by n-type doping seem to be responsible for the more efficient charge separation in $Sr_2Fe_{1-x}Ti_xNbO_6$ (0.05 < x < 0.4) and thus consequently displays higher photocatalytic activity. The Ti incorporated structure also found to yield stable photocatalyst.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.2
• /
• pp.230-238
• /
• 2017

We have proposed an InGaAs-based gate-all-around (GAA) tunneling field-effect transistor (TFET) with a stacked dual-metal gate (DMG). The electrical performances of the proposed TFET are evaluated through technology computer-aided design (TCAD) simulations. The simulation results show that the proposed TFET demonstrates improved DC performances including high on-state current ($I_{on}$) and steep subthreshold swing (S), in comparison with a single-metal gate (SMG) TFET with higher gate metal workfunction, as it has a thinner source-channel tunneling barrier width by low workfunction of source-side channel gate. The effects of the gate workfunction on $I_{on}$, the off-state current ($I_{off}$), and S in the DMG-TFETs are examined. The DMG-TFETs with PNPN structure demonstrate outstanding DC performances and RF characteristics with a higher n-type doping concentration in the $In_{0.8}Ga_{0.2}As$ source-side channel region.

• Journal of the Korean Chemical Society
• /
• v.41 no.9
• /
• pp.471-482
• /
• 1997

GC/MS was used to find an optimum experimental condition for the screening of organic acids in urine. Urinary organic acids were isolated through the liquid-liquid extraction method (LLE) to examine the influence of pH and the effect of including the back extraction and oximation processes respectively on the extraction. When pH was adjusted to 0.5 during the extraction without oximation process, relatively higher recovery rate and the smallest relative standard deviations (0.3-12.4%) were obtained. By removing the interference, the addition of back extraction made possible surer identification of organic acids with retention time of 15-16 minutes. Under this condition, we obtained the content distribution of urinary organic acids in healthy Korean children (n=16) by establishing the calibration curves for 51 standard organic acids.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.275-276
• /
• 2009

We have studied physical properties of organic light-emitting diodes (OLEDs) in a device with 7,7,8,8-tetracyanoquinodimethane (TCNQ). Since the TCNQ has a high electron affinity, it is widely used for a charge-transport and injection layer. And the TCNQ-derivatives have also been used to control the conductivity of the materials. It is known that a charge injection and transport in OLEDs with a TCNQ-derivative enhances a performance of the devices such as operating voltage and efficiency. To see how the TCNQ affects on the device performance, we have made a reference device in a structure of ITO(170nm)/TPD(40nm)/$Alq_3$(60nm)/LiF(0.5nm)/Al(100nm). And several type of devices were manufactured by doping TCNQ either in TPD or $Alq_3$ layer. The TCNQ layer was also formed in between the organic layers. N,N'-diphenyl-N,N'-di(m-tolyl)-benzidine (TPD), tri(8-hydroxy quinoline) aluminium ($Alq_3$), and TCNQ layers were formed by thermal evaporation at a pressure of $10^{-6}$ torr. The deposition rate was $1.0{\sim}1.5\;{\AA}/s$ for TPD, and $1.0{\sim}1.5\;{\AA}$ for $Alq_3$. The LiF was thermally evaporated at a deposition rate of $0.2\;{\AA}/s$ successively. The device with TCNQ-derivative improved the turn-on voltage compared to the one without TCNQ-derivative.

• Journal of the Korean Ceramic Society
• /
• v.42 no.9 s.280
• /
• pp.602-606
• /
• 2005

[ $LiCoO_{2}$ ] is the most common cathode electrode materials in Lithium-ion batteries. $LiCo_{0.97}Mg_{0.03}O_2$ was synthesized by the solid-state reaction method. We investigated crystal structures, electrical conductivities and electrochemical properties. The crystal structure of $LiCo_{0.97}Mg_{0.03}O_2$ was analyzed by X-ray powder diffraction and Rietveld refinement. The material showed a single phase of a layered structure with the space group R-3m. The lattice parameter(a, c) of $LiCo_{0.97}Mg_{0.03}O_2$ was larger than that of $LiCoO_2$. The electrical conductivity of sintered samples was measured by the Van der Pauw method. The electrical conductivities of $LiCoO_2$ and $LiCo_{0.97}Mg_{0.03}O_2$ were $2.11{\times}10^{-4}\;S/cm$ and $2.41{\times}10^{-1}\;S/cm$ at room temperature, respectively. On the basis of the Hall effect analysis, the increase in electrical conductivities of $LiCo_{0.97}Mg_{0.03}O_2$ is believed due to the increased carrier concentrations, while the carrier mobility was almost invariant. The electrochemical performance was investigated by coin cell test. $LiCo_{0.97}Mg_{0.03}O_2$ showed improved cycling performance as compared with $LiCoO_2$.

• Journal of Sensor Science and Technology
• /
• v.8 no.1
• /
• pp.53-62
• /
• 1999

Micro polysilicon actuators, which are widely used in the field of MEMS (Microelectromechanical System) technology, were fabricated using polysilicon thin layers. Polysilicon deposition were carried out to have symmetrical layer structures with a LPCVD (Low Pressure Chemical Vapor Deposition) system, and we have measured physical characteristics by micro test patterns, such as bridges and cantilevers to verify minimal mechanical stress and stress gradient in the polysilicon layers according to the methods of mutilayer deposition, doping, and thermal treatment, also, analyzed the properties of each specimen, which have a different process condition, by XRD, and SIMS etc.. Finally, the fabricated planar polysilicon resonator, symmetrically stacked to $6.5{\mu}m$ thickness, showed Q of 1270 and oscillation ampitude of $5{\mu}m$ under DC 15V, AC 0.05V, and 1000 mtorr pressure. The developed micro polysilicon resonator can be utilized to micro gyroscope and accelerometer sensor.