• Journal of the Korean Ceramic Society
• /
• v.38 no.11
• /
• pp.980-986
• /
• 2001

Bragg reflector type FBAR was fabricated on the Si(100) substrate. We measured a frequency response of the resonator at 5.2 GHz and analyzed it by numerical calculation considering actual acoustic losses of each layer in the structure. We fabricated nine layer Bragg reflector of W-SiO$_2$pairs using r.f. sputtering method and fabricated AlN piezoelectric and Al electrodes using pulsed dc sputtering. The return loss(S$_{11}$) of the fabricated Bragg reflector type FBAR was 12 dB at 5.38 GHz and the series resonance frequency(f$_{s}$) was 5.376 GHz and the parallel resonance frequency(f$_{p}$) was 5.3865 GHz. Effective electro-mechanical coupling constant (K$_{eff{^2}}$) and Quality factors(Q$_{s}$), the Figures of Merit of the resonator, were about 0.48% and 411, respectively. We extracted acoustic parameters of AlN piezoelectric and reflection coefficient of the Bragg reflector by numerical calculation. We could know that material acoustic impedance and wave velocity of AlN piezoelectric decreased for intrinsic value and the electromechanical coupling constant(K$_2$) value was very low owing to the poor quality of the AlN piezoelectric. Reflection coefficient of Bragg reflector was 0.99966 and reflection band was very wide from 2.5 to 9.5 GHz.

• Composites Research
• /
• v.26 no.3
• /
• pp.189-194
• /
• 2013

This paper deals with the study of mechanical properties and impact energy absorbed by composites, made by using thermoplastic and thermoset as matrix, flax fiber and nanoclay as reinforcements. The nanoclay was sprayed on the fiber laminate directly after mixing with ethanol. This experiment designed by Taguchi method and have variable factors, i.e three types of fiber direction(F), three different nanoclay wt%(N) and three spray gun hole shapes(S). According to these conditions, composites were made and the optimum conditions were found to be F1N3S1, F1N2S1, F1N2S1 and F3N2S1 for thermoplastic, and F1N3S2, F1N3S2, F1N2S2 and F3N2S1 for thermoset which were matched with tensile strength, modulus, total impact absorbed energy and heat release rate respectively.

• Journal of Food Hygiene and Safety
• /
• v.3 no.2
• /
• pp.53-58
• /
• 1988

This study was carried out to discuss a colorimetric method for the determination of nitrite in meat products issued by the Ministry of Health and Social Affaires of Korea (1985). 1) The recovery rates of nitrite of test solution extracted in the room temperature were higher than those obtained by the heating extraction. 2) In the room temperature, samples prepared with the sUce were more effective than the blendina method and the distlled water as extractina solvent for nitrite was more effective tban tbe phospbate buffer solution. 3) The extracting time showed that thirty minutes were enough to extract nitrite and the diazotizingcoupling reagents, 30% of sulfanilamide and N-l-naphthylethyienediamine were better than others. 4) The nitrite in a test soiution greatly decreased when the solution was distilled. In this case, the test solution should be used as a control. 5) Ten minutes were enough to couple nitrite.

• Journal of the Korean GEO-environmental Society
• /
• v.9 no.4
• /
• pp.77-84
• /
• 2008

Soil purification theory is the method using the soil micro-organism like aerobic and anaerobic for treatment of wastewater. The soil has many kinds of micro-organism and it multiply as change of the environment. Unlikely other methods, the soil purification theory is adaptable to inflow water change; moreover, it can process the T-N, T-P without any special method and management. The top is covered with the improved soil which can remove the bad smell and is used for resting place according to planting the lawn. This study is focused on analysis of the treatment processing of wastewater comparing inflow with outflow water. As a results, removal rate of the processing the BOD, COD and SS is almost 90~100% and it is 60~80% in T-N, T-P.

• Applied Chemistry for Engineering
• /
• v.33 no.4
• /
• pp.402-407
• /
• 2022

Statistical design of experiments was used to optimize the MOF-5 synthesis process. A mixture design was employed to optimize precursor concentration. The optimal composition of three chemical materials, terephthalic acid, zinc acetate dihydrate, and N,N-dimethylformamide for MOF-5 synthesis was determined by extreme vertices design methods as follows; 1 mol : 2.7 mol : 40 mol. A multilevel factorial design was selected to screen the significance of synthesis reaction conditions such as temperature, time, and stirring speed. Statistical analysis results suggested excluding stirring speed from further investigation. Using a central composition design, the synthesis time and temperature were optimized. The quadratic model equation was derived from 13 synthesis experiments. The model predicted that MOF-5 synthesized at 119 ℃ for 10.4 h had the highest crystallinity.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.406-413
• /
• 2000

The friction and wear behaviors of Magnetron Sputtered MoS$_2$films were investigated by using a pin on disk type tester which was designed and manufactured for this experiment. The experiment was conducted by using silicon nitride (Si$_3$N$_4$) as a pin material and Magnetron Sputtered MoS$_2$on bearing steel (STB2) as a disk material, under operating conditions that include different surface roughness (Polishing specimen, Grinding specimen)(2types), linear sliding velocities in the range of 22, 44, 66mm/sec (3types), normal loads vary from 9.8N, 19.6N, 29.4N(3types), corresponding to contact pressures of 1.9∼2.7GPa and atmospheric conditions of high vacuum( 1.3${\times}$10$\^$-4/Pa), medium vacuum( 1.3${\times}$10$\^$-l/Pa), ambient air(10$\^$5/Pa)(3types). We investigated fracture mechanism in magnetron sputtered MoS$_2$films with Magnetron Sputtering method in each experiment.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.2
• /
• pp.303-311
• /
• 1994

Optimum conditions for the deposition of N-docosylquinolium-TCNQ ultrathin organic films using the Langmuir-Blodgett etchnique and the molecular orientation and alignment of the LB films were studied. The $\pi$-A isotherm of the N-docosylquinolium-TCNQ was measured at the air-water interface varying with the subphase temperature, subphase pH, compressing speed and amounts of solutions for spreading. The LB film was deposited under the surface pressure of 30mN.m and 45mN/m and other deposition conditions. The molecular orientation and alignment of the LB films were studied by the polarization absorption technique. The $\pi$-A isotherm showed that the stable N-docosylquinolium -TCNQ monolayer was formed on the water surface at the condition of 25$^{\circ}C$,pH 5.6, molecular density of 2.1${\times}$10S014T~2.6${\times}$10S014T/cmS02T. The LB film was deposited under the surface pressure of 45mN/m had better packing density, orientation and alignment than the film of 30mN/m.

• Korean Journal of Crystallography
• /
• v.18 no.1_2
• /
• pp.1-6
• /
• 2007

An Organometallic compound, $C_{16}H_{35}B_{10}IrS_2Si$, was synthesized from o-carborane, $Cp^*Ir(S_2C_2B{10}H_{10})$, and $Me_3SiCHN_2$. The molecular structure of this complex has been determined by X-ray diffraction. Crystallographic data : monoclinic, space group $P2_1/n$, $a=10.1986(12)\;{\AA}$, $b=14.834(5)\;{\AA}$, $c=17.139\;{\AA}$, ${\beta}=92.24(2)^{\circ}$, Z=4, $V=2591.0(14)\;{\AA}^3$. The structure was solved by direct methods and refined by full-matrix leat-squares methods to give a model with a reliability factor R=0.053 for 5080 reflections.

• Journal of Navigation and Port Research
• /
• v.38 no.1
• /
• pp.45-52
• /
• 2014

Fractal theory has been widely used to quantify the complexity of remotely sensed digital elevation models and images. Despite successful applications of fractals to a variety of fields including computer graphics, engineering and geosciences, the performance of fractal estimators depends highly on data sampling. In this paper, we propose an algorithm for computing the fractal dimension based on the triangular prism method and a new sampling method. The proposed sampling method combines existing two methods, that is, the geometric step method and the divisor step method to increase pixel utilization. In addition, while the existing estimation methods are based on $N{\times}M$ window, the proposed method expands to $N{\times}M$ window. The proposed method is applied to generated fractal DEM, Brodatz's image DB and real images taken in the campus to demonstrate its feasibility.

• Microbiology and Biotechnology Letters
• /
• v.39 no.1
• /
• pp.70-76
• /
• 2011

PCR-based Weissella species-specific detection method was developed to apply for the discrimination of Korean and Chinese kimchi by detecting a Weissella species only found in Korean or Chinese kimchi. PCR primers were designed from the species-specific sequence in the recN gene of each species. The primers allowed the species-specific detection and identification of nine species in the genera Weissella, and were successfully applied to the detection of W. cibaria, W. confusa, W. koreensis, and W. soli in kimchi with 20 ng template DNA. W. cibaria, W. confusa, and W. koreensis were detected from the Korean kimchi samples tested but W. soli was not detected. However, the four species were detected from Chinese kimchi samples. PCR-based W. soli-specific detection could not be perfectly applied as the Chinese kimchi discriminating method but has significance as an approach to evaluate the potential of scientific verification method based on the difference of microbial community.