• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.2291-2294
• /
• 2003

In this paper, analysis and control design of ac-dc converter, normally nonlinear time-varying system, using sliding mode controller to achieve fast output voltage response, disturbance rejection and robust system in the presence of load variation are demonstrated. The objective of this method is to develop methodology for output voltage to be constant and input current sinusoidal that results in nearly unity power factor, respectively. In addition the converter can be also bidirectional power flow. Simulation results using Matlab/Simulink show the effectiveness of sliding mode control system compared with linear feedback controller to guarantee enhanced PF>0.98, THD<5%, and ripple output voltage is less than 1% at the maximum output power.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.504-508
• /
• 2004

An EMC analysis of a switched mode power supply (SMPS) have been usually using unbalance circuit topologies and the major factor of disturbance is parasitic capacitance. We have proposed a balanced switching converter circuit, which is an effective way to reduce the common mode conducted noise. In this paper presents the relationship between common mode current and radiated field.

• 한국전자파학회논문지
• /
• 제14권1호
• /
• pp.1-7
• /
• 2003

Davidenko 방법으로 정확하게 구하여진 정규화 복소 전파 상수로부터 원형 유전체 봉의 누설 모드를 조사하였다. 도파 모드의 차단 주파수 아래에서 nonphysical 영역, 안테나 모드 영역, Reactive 모드 영역, spectral gap영역 등의 독특한 주파수 영역이 관찰되었다.

• 전기학회논문지
• /
• 제59권3호
• /
• pp.575-580
• /
• 2010

This paper is to design an optimum power conversion device for the system required for development of a low cost 3-phase power inverter. For this purpose, in order to meet with endurance required by the industry, failure mode is standardized to guarantee lifetime of a power semiconductor by monitoring real time power loss and to facilitate failure mode analysis. As normality of heat loss of a power semiconductor is identified remaining in a certain range by comparing heat rise slope between that is calculated by using average current or average loss and that is measured at a heat sink, its feasibility is confirmed by experiment.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.654-659
• /
• 2007

In this paper, the fatigue load spectrum for tilt rotor UAV is developed and fatigue analysis is achieved for flaperon joint. Tilt rotor UAV has two modes which are helicopter mode when UAV is taking off and landing and fixed wing mode when UAV is cruising. To make fatigue load spectrum, FELIX for helicopter mode and TWIST for fixed wing mode are used. And Fatigue analysis of flaperon joint is achieved using fatigue load spectrum we obtained. When S-N test data are analyzed, we use the Kriging meta model to get probability S-N curve for whole range of material life. The result which is life of flaperon joint obtained by suggested fatigue analysis procedure in this paper is compared with that obtained by MSC/Fatigue.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 2003년도 한국우주과학회보 제12권2호
• /
• pp.41-41
• /
• 2003

Satellite formation flying is currently an active area of research in the aerospace engineering. There are many categories for this research such as the determination of initial conditions, formation keeping, configuration and reconfiguration. In this study, a tracking controller using sliding mode techniques is designed to control a satellite for the satellite formation flying. In general, Hill's equations are used to describe the relative motion of the follower satellite with respect to the leader satellite. But, the modified Hill's equations considering J2 perturbation were used for the design of sliding mode controller. Sliding mode control law causes the chattering phenomenon because it is a discontinuous control. Dead-zone was used to avoid the chattering. The Extended Kalman filter was applied to estimate the state vector based on the measurements of relative distance and velocity between two satellites.

• Current Optics and Photonics
• /
• 제2권1호
• /
• pp.85-89
• /
• 2018

This paper presents a new, efficient hybrid photonic-plasmonic structure. The proposed structure efficiently and with very high accuracy combines the resonant mode of a low-mode-volume photonic-crystal nanocavity with a bowtie nanoantenna's plasmonic resonance. The resulting enormous enhancement of light intensity of about $1.1{\times}10^7$ in the gap region of the bowtie nanoantenna, due to the effective optical-resonance combination, is realized by subtle optimization of the nanocavity's optical characteristics. This coupled structure holds great promise for many applications relying on strong confinement and enhancement of optical field in nanoscale volumes, including antennas (communication and information), optical trapping and manipulation, sensors, data storage, nonlinear optics, and lasers.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제16권4호
• /
• pp.305-312
• /
• 2016

Purpose: The purpose of this study is to provide a sensitivity analysis of system reliability for recognizing effectiveness of changing of BD mode failures using reliability growth projection model based on NHPP. Methods: Crow extended reliability projection model (CERPM) is used to analyze the changing of two factors 1) the number of BD mode failures, 2) fix effectiveness factor (FEF) values. Results: The system reliability has increased in accordance with the number of BD mode failures and FEF values have increased. Conclusion: It is necessary to design failure modes and FEF values to supervise the reliability.

• 한국철도학회논문집
• /
• 제6권4호
• /
• pp.286-293
• /
• 2003

The prototype of Korean high speed train (HSR350), composed of two power cars, two motorized cars and three trailer cars, has been designed, fabricated and tested. In this paper, the body vibration has been reviewed from the viewpoint of the vehicle's safety and the vibration limits for components and sub-assemblies mounted on the car-body using by the experimental method. And, the dynamic characteristics, such as jerk, natural mode and kinematic mode, have been reviewed. The KHST has been run to 300 km/h in the KTX line and the results of on-line test show that it has no problems in the vehicle's safety and the vibration limits. And the characteristics of body vibrations has been predicted at 350 km/h by fitting curve about the measured acceleration signals.

• 한국자동차공학회논문집
• /
• 제12권6호
• /
• pp.119-126
• /
• 2004

In order to elucidate the modes of double-droplet combustion speed in premixed spray flame, the difference between flame propagation speed and droplet cluster disappearance speed are experimentally investigated using a premixed spray burner system, It was confirmed that flame speed concerned with premixed-mode combustion in the spray flame was approximately 2.0 m/s in average while mean disappearance speed of droplet clusters, which were dominated by diffusion-mode combustion in downstream of the flame, was evaluated as much as 0.45 m/s. It was clarified that both characteristics of premixed-mode and diffusion-mode combustion in spray flames are of much difference in nature, even though both speed, which are supposed to depend on local properties of the spray itself and flow conditions surrounding droplet clusters, are scattered in experiments.