• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.583-586
• /
• 2017

Infrared signal measurement are conducted from a micro-turbo jet engine with different nozzle configurations. The conventional cone type, a S-shaped type with aspect ratio 5.2 and five rectangular type nozzle with different aspect ratios are used for this experiment work. The result show that infrared signal from the exhaust gas decrease as the aspect ratio increase. In case of S-shaped nozzle, the maximum infrared signal is reduced about 28.4% when compared of rectangular nozzle with aspect ratio 5(AR5).

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.38.2-38.2
• /
• 2009

마이크로노즐은 우주공간에서 인공위성의 자세를 바로잡는 데 필요한 마이크로 로켓에 들어가는 필수적인 부품이다. 마이크로 노즐은 또한 나노입자 적층 시스템(nano-particle deposition system, NPDS)에 들어갈 수 있다. NPDS는 세라믹 또는 금속 나노분말 입자를 노즐을 통해 초음속으로 가속시킨 뒤 상온에서 이를 기판에 적층시키는 새로운 시스템이다. 본 연구의 목표는 NPDS에 쓰이는 노즐을 일반적인 반도체 공정을 이용하여 마이크론 스케일의 목을 갖도록 한 마이크로노즐을 제작하는 데 있다. 보쉬 공정은 이러한 마이크로노즐을 제작하는데 필수적인 공정으로, 유도결합플라즈마를 이용해 실리콘 웨이퍼를 식각시키는 기술을 말한다. 보쉬 공정에 사용되는 플라즈마 기체는 $SF_6$와 $C_4F_8$인데, 이 두 가지 기체를 번갈아가면서 사용하여 실리콘 웨이퍼를 이방성 식각하는 것이 그 특징이다. 보쉬 공정에는 다양한 변수가 존재하며 이를 적절히 통제하면 마이크로노즐에 적합한 프로파일을 실리콘 웨이퍼 내에 형성시킬 수 있다. 본 연구에서는 보쉬 공정을 이용하여 3차원 마이크로 노즐을 제작하였다. 기존에 반응성이온식각(deep reactive ion etching, DRIE) 공정을 통해 마이크로노즐을 제작한 사례가 많이 보고되었지만 이들은 모두 2차원적으로 마이크로노즐을 제작하였다. 2차원적으로 제작한 마이크로노즐은 마이크로 로켓에 주로 사용되었지만, 초음속으로 가속된 분말이 노즐의 형상으로 인한 유체 흐름의 불안정성 때문에 NPDS에서는 오래도록 사용할 수 없다는 문제점이 있다. 그러므로 본 연구에서는 마이크로노즐을 3차원 형상으로 제작함으로써 이러한 문제점을 해결하고자 하였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.1
• /
• pp.10-18
• /
• 2009

Numerical simulation has been performed in this study to investigate the capabilities of turbulence modeling schemes on estimating the film cooling at a referenced parallel wall jet-nozzle configuration. Also a additional simulation has been performed for film cooling under 2-dimensional axis symmetry conditions at a parallel wall jet-nozzle configuration. It was concluded that the best turbulence model is the standard $k-{\epsilon}$ model with enhanced wall functions. Also a additional simulation showed the film cooling characteristics that are resonable physically.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.3
• /
• pp.42-55
• /
• 2021

In this study, the effect of nozzle performance according to the selection of the center line equation. Three of S-type nozzles and three of double S-type nozzles were designed using the curve equation and design parameters, and the nozzle shielding performance was evaluated using the shielding ratio definition. In order to analyze the internal flow of the nozzle, the characteristics of the velocity distribution and pressure distribution were studied, and the nozzle performance was evaluated through the total thrust ratio(f) and the nozzle insulation efficiency coefficient(η). On the other hand, the centerline with a sharply change in curvature at the entrance has a low nozzle performance and a high shielding rate. The double S-type nozzle is excellent nozzle performance and shielding rate by using a smooth centerline at the first curvature.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.2
• /
• pp.8-14
• /
• 2008

Solid Rocket Motor(SRM) has advantages such as - high specific impulse, operational safety and simplicity in design and manufacturing process but thrust magnitude can't be controlled. For studying of pintle nozzle that can control the thrust magnitude of SRM, cold flow test and numerical analysis about needle type pintle shape were performed and results were presented in this paper. As the results of this study, pintle tip's shape and nozzle contour were important design parameters because thrust performance and variable thrust range of pintle nozzle depend on them. Especially, the thrust of needle typed pintle nozzle adopted in this test was predicted 13% higher than normal nozzle without pintle.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.289-294
• /
• 2007

Solid Rocket Motor(SRM) has advantages such as - high specific impulse, operational safety and simplicity in design and manufacturing process, but thrust magnitude can't be controlled. For studying of pintle nozzle that can control the thrust magnitude of SRM, cold flow test and numerical analysis about needle type pintle shape were performed and results were presented in this paper. As the results of this study, pintle tip's shape and nozzle contour were important design parameters because thrust performance and variable thrust range of pintle nozzle depend on them. Especially, the thrust of needle typed pintle nozzle adopted in this test was predicted 13% higher than normal nozzle without pintle.

• Journal of Power System Engineering
• /
• v.14 no.2
• /
• pp.22-27
• /
• 2010

본 논문은 유한체적법에 근거한 CFD 분석기법을 이용하여 증기 이젝터의 성능에 대하여 구동노즐의 기하학적 형상에 따른 영향을 조사하였다. 구동노즐의 직경비를 변화시키고 또한 직경비를 일정하게하고 구동 노즐의 위치를 변화시키면서 최적의 조건을 조사하였다. 연구 결과 이젝터의 성능은 구동노즐의 직경과 노즐의 출구 위치에 의해 좌우됨을 확인하였다. 일정 노즐 면적비에 대하여 노즐 목 직경이 감소함에 따라 혼입율이 증가하는 것을 확인하였고 일정 노즐 목 직경에 대하여 면적비의 증가는 혼입율의 감소의 원인이 된다는 것을 확인할 수 있었다. 또한 혼입율은 노즐의 출구 위치에 따라 영향을 받는다는 것도 확인하였다. 혼입율은 노즐 출구의 위치가 이젝터의 상류로 이동할수록 증가하고 그 위치는 이젝터의 일정단면적부 직경(D)에 대하여 0.4D일 때 최적의 성능을 보였다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.6 no.2
• /
• pp.1-7
• /
• 2002

In the modern propulsion systems, requited thrust is obtained using a nozzle. Sometimes shock and induced boundary layer separation is generated in an over-expanded convergent-divergent supersonic nozzle. It occurs because the nozzle expansion ratio is too large for a given nozzle pressure ratio (NPR). This phenomenon can be explained that it redefines effective nozzle geometry, shorer nozzle geometry and lower pressure ratio, in a given pressure ratio. Numerical studies were conducted about a fixed geometry 2D nozzle in overexpanded condition and compared with Hunter's experimental result. For the numerical simulation of the supersonic nozzle, Navier-Stokes equations are considered and as a turbulent model, $\kappa$-$\varepsilon$ /$\kappa$-$\omega$ blended SST two equation turbulent model is used. The characteristics of $\lambda$-shape shock systems due to the interaction of shock and boundary layer was investigated in a low NPR. And the result of comparison of thrust value shows that a fixed geometry nozzle can cover required flight mission.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.34-39
• /
• 2005

In this study, 3-D nozzle shape and the shape of nozzle at exit plane were adopted as design parameter of 3-D supersonic nozzle and numerical analyses for these parameters have been performed to investigate the flow and performance characteristics for design parameters of the turbine. Firstly, comparing results for nozzle shape, rectangular nozzle had less total pressure loss occurred in axial gap and more power by 1.5% than circular nozzle did. Next, comparing the results for the shape of nozzle at exit plane, it is found that the performance of partial admission turbine was largely depended upon the gap between nozzle wall at exit plane and the hub / tip of rotor blade and the length between nozzles.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.7
• /
• pp.939-944
• /
• 2018

Clean fire extinguishing agents refer to chemical that can replace Halon 1211 and Halon 1310 according to the Montreal Protocol fermented to protect the Earth's ozone layer. In Korea and abroad, system standardization and performance evaluation of clean fire extinguishing agents are being carried out. This paper proposes an optimal nozzle shape by modeling and numerical analysis of various nozzle shapes based on general clean fire extinguishing system. The ejection speed of the nozzle can be improved by studying three - dimensional modeling of the nozzle for two shapes, Type A and B. Flow analysis was performed on the two types of nozzles and the gas velocity and pressure distribution were measured with different nozzle diameters. It was confirmed that the jetting speed was changed at the nozzle outlet according to the number and diameter of the nozzle holes. The flow rate increased with increasing the pressure regardless of the nozzle hole diameter. Based on the results obtained from the experiment, the K-factor value was deduced. Finally, a nozzle with a 12-hole structure with a 5-mm nozzle hole was proposed.