• Advances in environmental research
• /
• v.2 no.3
• /
• pp.167-177
• /
• 2013

We investigated that removal of aqueous U(VI) by nano-sized Zero Valent Iron (nZVI) and Fe(II) bearing minerals (controls) in this study. Iron particles showed different U(VI) removal efficiencies (Mackinawite: 99%, green rust: 95%, nZVI: 91%, magnetite: 87%, pyrite: 59%) due to their different PZC (Point of Zero Charge) values and surface areas. In addition, noticeable amount of surface Fe(II) (181 ${\mu}M$) was released from nZVI suspension in 6 h and it increased to 384 ${\mu}M$ in the presence of U(VI) due to ion-exchange of U(VI) with Fe(II) on nZVI surface. Analysis of Laser-Induced Breakdown Detection (LIBD) showed that breakdown probabilities in both filtrates by 20 and 200 nm sizes was almost 24% in nZVI suspension with U(VI), while 1% of the probabilities were observed in nZVI suspension without U(VI). It indicated that Fe(II) colloids in the range under 20 nm were generated during the interaction of U(VI) and nZVI. Our results suggest that Fe(II) colloids generated via ion-exchange process should be carefully concerned during long-term remediation site contaminated by U(VI) because U could be transported to remote area through the adsorption on Fe(II) colloids.

• Tribology and Lubricants
• /
• v.28 no.1
• /
• pp.33-37
• /
• 2012

Automotive wheel bearing grease helps to reduce stresses and prevent wear of wheel bearings. But it is easily contaminated by water and other contaminants. Previously, our research group reported the change of grease physical properties such as dropping point, work penetration and oxidation work stability, water washout characteristics, leakage tendency, oil separation, evaporation loss and rust protection by water contamination. In this paper, we analyzed the physical characteristics of grease such as lubricity, viscosity and total acid number to investigate the mechanism of thickener decomposition. In water contaminated grease, the total acid number and wear scar were increased, the viscosity was decreased due to the decomposition of lithium complex thickener.

• Korean journal of applied entomology
• /
• v.42 no.3
• /
• pp.185-195
• /
• 2003

Phytoseiid mites are important predators of spider mites, rust mites and many of insect pests as well. From two-year (2001-2002) survey of apple orchards in Kyoungbuk and Suwon area, 13 species of phytoseiids, 12 species of the genus Amblyseius and one species of the genus Typhlodromus were found. Among them, Amblyseius womersleyi was the most dominant followed by A. rademacheri, A. orientalis, and A. makuwa. Amblyseius rademacheri and A. makuwa were mainly found from ground vegetation. Keys to genera and species were presented with some pictorial details and ecological notes of each species. Further discussion on systematics of the family Phytoseiidae and use in apple IPM were suggested.

• Corrosion Science and Technology
• /
• v.13 no.5
• /
• pp.163-169
• /
• 2014

The corrosion resistance of epoxy-coated carbon steel was evaluated. The carbon steel surface was subjected to different treatment methods such as steel grit blasting and power tool treatment as well as contamination of water soluble salt. To study the effect of the surface treatments and contamination, the topology of the treated surface was observed by confocal microscopy and a pull-off adhesion test was conducted. The corrosion resistance of the epoxy-coated carbon steel was further examined by electrochemical impedance spectroscopy (EIS) combined with immersion test of 3.5 wt% of NaCl solution. Consequently, the surface contamination by sodium chloride with $16mg/m^2$, $48mg/m^2$ and $96mg/m^2$ didn't affect the adhesion strength for current epoxy coated carbon steel and blister and rust were not observed on the surface of epoxy coating contaminated by various concentration of sodium chloride after 20 weeks of immersion in 3.5 wt% NaCl aqueous solutions. In addition, the results of EIS test showed that the epoxy-coated carbon steel treated with steel grit blasting and power tool showed similar corrosion protection performance and surface cleanness such as Sa 3 and Sa 2.5 didn't affect the corrosion protectiveness of epoxy coated carbon steel.

• Proceedings of the Korean Society of Plant Pathology Conference
• /
• 2003.10a
• /
• pp.25-27
• /
• 2003

Since 1993, a total of 50 problematic plant diseases unrecorded in Korea were surveyed in Gyeongnam province. Totally 34 new host plants to corresponding pathogens investigated in this study were 5 fruit trees, 9 vegetables, 12 ornamental plants, 3 industrial crops, and 5 medicinal plants. Among the newly recorded fruit tree diseases, fruit rot of pomegranate caused by Coniella granati and Rhizopus soft rot of peach caused by Rhizopus nigricans damaged severely showing 65.5% and 82.4% infection rate. Among the vegetable diseases, corynespora leaf spot of pepper caused by Corynespora cassiicola and the crown gall of pepper caused by Agrobacterium tumefaciens, powdery mildew of tomato caused by Oidiopsis taurica were the most severe revealing 47.6%, 84.7%, and 54.5% infection rate in heavily infected fields, respectively. In ornamental plants, collar rot of lily caused by Sclerotium rolfsii, gray mold of primula caused by Botrytis cinerea, soot leaf blight of dendrobium caused by Pseudocercospora dendrobium, sclerotinia rot of obedient plant caused by Sclerotinia sclerotiorum showed 32.7 to 64.8% disease incidence. On three industrial plants such as sword bean, broad bean, and cowpea, eight diseases were firstly found in this study. Among the diseases occurring on broad bean, rust caused by Uromyces viciae-fabae and red spot caused by Botrytis fabae were the major limiting factor for the cultivation of the plant showing over 64% infection rate in fields. In medicinal plants, anthracnose of safflower caused by Collectotrichum acutatum was considered the most severe disease on the plant and followed by collar rot caused by Sclerotium rolfsii.(중략)

• Proceedings of the Korea Concrete Institute Conference
• /
• 1994.04a
• /
• pp.148-151
• /
• 1994

Up to now, sea sand without complete removal of salt is being used in the construction works because there is little satisfactory counterplan for the substitute aggregate. In the case that such sea sand is used in the reinforced concrete, the residual salt gives rise to deterioration phenmenon and iron corrosion, reducing durability of the ferro-concrete structures. The paper, an experimental study on the effect of corrosion protection by tighting concrete used SF and FA, is to investigate general steel bar's corrosion and to develop concrete using sea sand economically after it is analyzed and examinated ratio of the corrosion area affected by the autoclave cycle. As a test results, as for corrosion area ratio, it is very effective to use admixrutes such as SF and FA which decrease corrosion area remarkably with increasing the amounts of admixtures. Accordingly the use of admixtures is advantageous for tightening concrete and has an effect of salt damage prevention and rust protection in concrete used sea sand.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.8
• /
• pp.96-103
• /
• 2009

The roll forming process is commonly used for the conventional 'Fe' metal products such as a furniture drawer guide or an up-down slide guide. Recently its applications are variously expanded to the sanitary facilities or electronic devices. It is essentially required the cleanness for the high technology application and any corrosion or rust are not allowed. Therefore, in those applications the stainless steel materials are strongly demanded as the substitution of 'Fe' steel. However the mechanical properties of stainless steel are not suitable for forming process compared with those of 'Fe' steel. Up to now, the conventional F.E.M.(Finite Element Method) has been used to analyze and design the roll forming process. The purpose of this research is to obtain the proper production process and the shape of rolls to manufacture the high precision slide rails made of stainless steel material. The commercial program, SHARPE-RF, is used to analyze the entire roll forming process. The results show that the rolling process and the roll design by F.E.M. are useful from the good agreement between the shapes of products estimated by F.E.M. and those of the actual products.

• Journal of Korean Society of Water and Wastewater
• /
• v.29 no.4
• /
• pp.459-468
• /
• 2015

Deposits discharged through the cleaning mainly were cement mortar, bitumen paintings and rust pieces, and fragments of perforation, stones and gravels. Deposits were more removed through swabbing pig cleaning rather than air scouring cleaning on the whole. However, air scouring cleaning were not influenced by the constraint conditions such as a change in the diameter or the presence of the valve in water mains compare to swabbing pig cleaning. So, it was thought that air scouring cleaning might be more favorable to water distribution network cleaning in the future. After the cleaning, water quality including residual chlorine and turbidity also was improved because of the removal of a significant amount of the deposits. Therefore, if the cleaning is continuously and regularly implemented in water mains, it is expected that it will help to recover the reliability and to preserve the health of water quality.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.1
• /
• pp.35-47
• /
• 2011

For the synthesis of water soluble acrylic modified epoxyester resin, fatty acid/epoxy ratio of 50/50 was used, and introduced maleic anhydride. Ratio of styrene/acrylic acid of acrylic monomers was fixed 85/15 and ratio of epoxyester/acrylic monomer was controlled 80/20, 75/25, 70/30, 65/35, and degree of neutralization were changed 65%, 80%, to 100%. As a result, 40% solids acrylic modified epoxyester resins were synthesized. Resins were evaluated water soluble stability, drying time, water resistant, storage stability and physical properties. And the white paints were prepared, and were evaluated viscosity, drying time, water resistance, adhesion, sagging, spray workability, gloss, salt spray resistance, skinning, whiteness and flash rust. As a result, the degree of neutralization of 100% and the ratio of epoxyester/acrylic monomer of 75/25 showed the best properties.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.493-497
• /
• 2000

A battery is the device that transforms the chemical energy into the direct-current electrical energy without a mechanical process. Unit cells are connected in series to obtain the required voltage while being connected in parallel to organize capacity for load current. Because the voltage drop down in one set of battery is faster than in two one it may result in the low efficiency of power converter with the voltage drop and cause the system shutdown. However when the system being shutdown. However when the system being driven in parallel a circular-current can be generated,. It is shown that as a result the new batteries are heated by over-charge and over-discharge and the over charge current increases rust of the positive grid and consequently shortens the lifetime of the new batteries. The difference between the new batteries and old ones is the amount of internal resistance. In this paper we can detect the unbalance current using the microprocessor and achieve the balance current by adjusting resistance of each set, The internal resistance of each set becomes constant and the current of charge and discharge comes to be balanced by inserting the external resistance into the system and calculating the change of internal resistance.