• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.4
• /
• pp.365-373
• /
• 2008

Fiber Reinforced Polymer, FRP has a light weight, a high tensile strength based on design, non-electronic, non-magnetic, and rust-resistant feature, etc and many researches are being conducted recently on FRP in the construction area. Among them, GFRP (Glass Fiber Reinforced Polymer) is excellent in price competitiveness and is widely being used. However, since GFRP has a relative low modulus of elasticity and causes excessive deflection, the section must be large to be used as a structural component and an investigative review must be carried out in design to set the limit for deflection by the use load. Therefore, in order to solve the mentioned technical problems, this study suggested a section of a module form such that application of a large-scale section is possible. Also, to secure the low rigidity of FRP, this study developed a new FRP+ concrete composite girder form that confined the concrete. To identify the structural movement of the developed FRP+ concrete composite girder, shear strength test was carried out.

• Corrosion Science and Technology
• /
• v.17 no.1
• /
• pp.12-19
• /
• 2018

Langelier Index (LI) is used as a tap water corrosiveness index. Residual chlorine in tap water induces corrosion inside water pipes. This study takes a deeper look into the effect of residual chlorine in water pipes. Comparison between tap waters of Y and K water treatment plant (WTP) shows that the LI index of K WTP is lower than that of Y. However, the corrosion rate of Y WTP is higher than that of K WTP. This means that the higher the concentration of residual chlorine in tap water, the higher the corrosion rate of pipe materials. When calcium hydroxide was added to tap water, the corrosiveness index was improved and thus the corrosion rate reduced. It is possible to increase the disinfection efficiency by increasing the duration of residual chlorine and suppressing the rust generation of water pipes and to supply minerals. A guideline for corrosion control with residual chlorine should be set up. The effects of residual chlorine should be included in the corrosiveness index of tap water.

• Mycobiology
• /
• v.31 no.3
• /
• pp.179-182
• /
• 2003

A total of 187 endophytic fungi were isolated from 11 plant species, which were collected from 11 locations in Korea. Their antifungal activities were screened in vivo by antifungal bioassays after they were cultured in potato dextrose broth and rice solid media. Antifungal activity against plant pathogenic fungi such as Magnaporthe grisea(rice blast), Corticium sasaki(rice sheath blight), Botrytis cinerea(tomato gray mold), Phytophthora infestans(tomato late blight), Puccinia recondita(wheat leaf rust), and Blumeria graminis f. sp. hordei(barley powdery mildew) was determined in vivo by observing the inhibition of plant disease development. Twenty(11.7%) endophytic fungi fermentation broths were able to control, by more than 90%, at least one of the six plant diseases tested. Among 187 liquid broths, the F0010 strain isolated from Abies holophylla had the most potent disease control activity; it showed control values of more than 90% against five plant diseases, except for tomato late blight. On the other hand, fourteen(7.5%) solid culture extracts exhibited potent disease control values of more than 90% against one of six plant diseases. The screening results of this study strongly suggested that metabolites of plant endophytic fungi could be good potential sources for screening programs of bioactive natural products.

• Applied Biological Chemistry
• /
• v.45 no.3
• /
• pp.157-161
• /
• 2002

New 2-benzoylimino-1,3-oxathile derivatives 3 were synthesized and tested their fungicidal activities for the development of new agrochemical fungicide. Reaction of ${\gamma}-chloro-{\beta}-keto$ anilide derivative 5 with potassium thiocyanate followed by the treatment of acid catalyst gave cyclyzed 2-imino-1,3-oxathiole 3. New compound 3 reacted with benzoyl· chlorides to afford the corresponding 2-benzoylimino-1,3-oxathiole derivatives 7. Antifungal screening (in vivo) of the synthesized compounds against typical plant diseases, which include rice blast, rice sheath blight, cucumber gray mold, tomato late blight, wheat leaf rust, and barley powdery mildew, was carried out. No significant fungicidal activities were shown of the synthesized compounds at 100 mg/l.

• Journal of Ginseng Research
• /
• v.39 no.2
• /
• pp.94-104
• /
• 2015

Background: Ginseng (Panax ginseng Meyer) is an important medicinal herbs in Asia. However, ginseng varieties are less developed. Method: To developed ginseng varieties, a pure line selection method was applied in this study. Results: Gumpoong was testing of 4-yr-old specimens in 2002, the proportions of the below-ground roots that were rusty colored for Gumpoong was 1.29 in Daejeon and 1.45 in Eumseong, whereas the proportions for its yellow berry variant were 2.60 and 2.45 in the two regions, respectively. Thus the Gumpoong was resistant to root rust. Sunpoong has a high yielding property. Its average root weight is 70.6 g for 6-yr-old roots. Its yield is 2.9 kg/$1.62m^2$ and the rate of heaven- and earth-grade product is 20.9%, which is very high compared to 9.4% for Yunpoong. Sunone is resistance to root rot and the survival rate of 4-yr-old roots was 44.4% in 1997, whereas that of the violet-stem variant landrace was 21.7%. Sunhyang has content of arginyl-fructosyl-glucose (AFG), which produces the unique scent of red ginseng, is $95.1{\mu}mol/g$ and greater than the $30.8{\mu}mol/g$ of Chunpoong in 6-yr-old plants. Sunun and Cheongsun are being nurtured to protect genetic resources. Conclusion: Developed ginsneg varieties will be used as the basis for the protection of genetic resources and breeding.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.505-508
• /
• 2008

Concrete is a type of porous materials and is physically and chemically damaged due to exposure to various environments from the placing to the service life. These reactions affect the corrosionof steel bars applied in concrete and that decreases the durability life and strength of such steel bars. Thus, it is very important to insert rust inhibitors into steel bars in the case of a deterioration element that exceeds the critical amount of corrosion in the location of steel bars. However, it is very difficult to guarantee corrosion resistance at the location of steel bars using conventional technology that applies corrosion inhibitors only on the surface of concrete. This study attempts to develop a method that penetrates corrosion inhibitors up to the location of steel bars and investigate the penetration depth of corrosion inhibitors by verifying moisture migration in concrete under an applied pressure.

• Journal of the Korean Institute of Gas
• /
• v.17 no.3
• /
• pp.14-19
• /
• 2013

This paper presents an experimental study on the safety of a valve for a special gas cylinder. The test valves that were randomly dismantled from the special gas cylinder were experimented on the gas leakage and operation safeties. The crack, wear and deformation of the valve body, screw thread, safety disk, vent hole, stem and handle components that may affect to the gas leakage safety of a used valve were not found in this experimental study. A painted handle of a valve was partly stripped from the coated surface, and the surface of PT screw of a used valve body was rusted. But, these paint and rust problems do not affected to the gas leakage safety of used valves. And there was no gas leakage in the dismantled valve, and the permanent deformation and partial scars of a valve stem and O-rings were observed on the rubbing surfaces. Thus, the valve seat and O-rings are recommended to be replaced for a gas leakage safety of a dismantled valve. And it is necessary to repair and inspect handle fastening forces for a safe opening and closing operations of a valve.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.1
• /
• pp.34-42
• /
• 2001

A battery is the device that transforms the chemical energy into the direct-current electrical energy directly without a mechanical process. Unit cells are connected in series to obtain the required voltage, while being connected in parallel to organize capacity for load current and to decrease the internal resistance for corresponding the sudden shift of the load current. Because the voltage droop down in one set of battery is faster than in tow one, it amy result in the low efficiency of power converter with the voltage drop and cause the system shutdown. However, when the system being driven in parallel, a circular-current can be generated. The changing current differs in each set of battery because the system including batteries, rectifiers and loads is connected in parallel and it makes the charge voltage constant. It is shown that, as a result the new batteries are heated by over-charge and over-discharge, and the over charge current increases rust of the positive grid and consequently shortens the lifetime of the new batteries. The difference between the new batteries and old ones is the amount of internal resistance. In this paper, we can detect the unbalance current using the micro-processor and achieve the balance current by adjusting resistance of each set. The internal resistance of each set becomes constant and the current of charge and discharge comes to be balanced by inserting the external resistance into the system and calculating the change of internal resistance.

• Corrosion Science and Technology
• /
• v.6 no.5
• /
• pp.257-260
• /
• 2007

In order to further improve the corrosion resistance and wear resistance of the Ni-P coatings of electroless plating, electroless Ni-P/n-$Al_2O_3$ composite deposits were prepared by adding some nano $Al_2O_3$ Particles in Ni-P plating bath. The bath composition and proproties were studied in this paper. The orthogonal test was applied in order to get the new composite solution, taking the initial stable potential as evaluation standard and considering the elements correlation at the same time. The processing parameters have been optimized by single factor experiment in which the depositing speed was chosen as the evaluation standard. The results showed that the process is stable and the composite Ni-P/n-$Al_2O_3$ deposits werebright and smooth, whose hardness and corrosion resistance are much better than simple Ni-P coatings. Furthermore the surface appearance and structure of the composite Ni-P/n-$Al_2O_3$ coating were investigated by SEM and XRD method. It was proved that the coating surface is typical cystiform cells and its structure is amorphous. All test results ofcomposite coating showed that all various physical coating properties had been improved by adding nano-particles. The hardness of optimal coating is more than 600HV and increases to 1000HV after heat-treating, and its hardness is 20~50% higher than Ni-P coating. The rust points appeared in 200 hour by immersing the coating into the 10%HCl solution and the corrosive speed is $3{\times}10^{-3}mg/(cm^2{\cdot}h)$which was obtained after 300 hour. In the same condition Ni-P coating is $5.6{\times}10^{-3}mg/(cm^2{\cdot}h)$. The salt spray resistance of the layers can exceed 600h with the thickness $20{\mu}m$.

• Fire Science and Engineering
• /
• v.34 no.3
• /
• pp.8-17
• /
• 2020

In this study, the characteristics of HFIX insulated wire sheaths contaminated by pollutants were examined. KS C IEC 60811-1-3 standard was followed in performing the water-resistance wire tests. Pollutants were selected, and the specimens were exposed to the pollutants for a maximum duration of four weeks. The maximum tensile load and the elongation rate were measured each week. As the period of pollution exposure increased, the maximum tensile load of the specimens decreased by 6.22% and 6.52% at room temperature and high temperature, respectively, and 19.94% for specimens coated with a rust-proof lubricant. The elongation rate also decreased rapidly, such that the reductions in the properties of the sheath were significant. From the analysis of the surfaces using a scanning microscope, as the contamination period increased, structural changes such as perforation, split, and melting occurred, and the mechanical properties of the specimens decreased. Therefore, it is necessary to develop and follow an inspection cycle and periodically carry out repairs to prevent the deterioration of insulated wires.