• Composites Research
• /
• v.14 no.1
• /
• pp.15-21
• /
• 2001

The pressing roller was designed and manufactured with high modulus carbon fiber composite material to exploit the high specific stiffness of the composite material. the optimal stacking sequence for the pressing roller was obtained from the FE analysis and the shape of the rubber coating layer was determined based on the calculated deflection for the uniform pressure on the film along the axial length of the pressing roller. Then the static deflection of the manufactured composite pressing roller was experimentally evaluated in comparison with analysis result and dynamic characteristics were measured through vibrational test.

• Journal of Power System Engineering
• /
• v.17 no.1
• /
• pp.85-90
• /
• 2013

Dry CVT consists of a driving pulley and a driven pulley joined by rubber V-belt. Each pulley consists of a fixed flange and a movable flange. The movable flange moves toward a fixed flange under the actuation of a centrifugal roller, as the driving pulley speed increases. The important claim which have an influence on the performance of the Dry CVT is the wear of the centrifugal roller. In this study ball type is proposed instead of roller type of movable flange to resolve the claim. Simulation is carried out for new model to verificate performance, experiments are carried out for new model to evaluate performances.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.3
• /
• pp.303-309
• /
• 2015

In this study, a vehicle dynamic analysis and roller rig test were performed to evaluate the applicability of a suspensionless composite bogie to railway vehicles. A vehicle dynamic analysis was carried out under different rubber bushing stiffness values. The stiffness of the rubber bushing that plays a role in guiding wheel sets was varied in the range of 10-100 MN/m, in 10-MN/m steps. Based on the results, the composite bogie with a rubber bushing stiffness of more than 40 MN/m satisfied the design requirements. In addition, a rubber bushing with a stiffness of 81 MN/m was fabricated, and a roller rig test was performed. Based on the test results, the vehicle equipped with the composite bogie had a critical speed of 363 km/h, which agreed with the simulation result within an error of 10%.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.23 no.9
• /
• pp.620-626
• /
• 2011

The purpose of this study is to evaluate a simulation model of a stacking guidance system (SGS) with a roller guide applicable to the mobile harbor. The study used a small-scale model (1/20) made of wood with rollers in order to compare the dynamic analysis with experiment results. The law of similarity was applied for the validation of the scaled model. In order to construct a more realistic simulation model, the damping coefficient of the dynamic model was adjusted to 0.5 Ns/mm for the wood-to-wood contact condition based on the experimental results. Using this validated model, dynamic simulations were also carried out for containers of 20, 30, and 40 tons. The results showed that the reaction force of the roller guide was increased from 74.7 kN to 91.2 kN as the weight of container increased. For the design of a roller guide for SGS, the results obtained in this study can be used to reduce the reaction force by employing a rubber roller or a highly damped rotational joint.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.2
• /
• pp.129-135
• /
• 2011

Dry CVT(Continuously variable transmission) consists of a driving pulley and a driven pulley joined by rubber V-belt. Each pulley consists of a fixed flange and a movable flange. The movable flange of the driving pulley has the centrifugal roller and a ramp plate in the flange. The movable flange moves toward a fixed flange under the actuation of a centrifugal roller, as the driving pulley speed increases. The main advantages of the Dry CVT with V-belt, which has been popular in Asia, are a simple mechanism, less maintenance and low cost. The important claim which have an influence on the performance of the Dry CVT is the wear of the centrifugal roller. In this study ball type is proposed instead of roller type of movable flange to resolve claim. Also experiments are carried out for new model to evaluate performances.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.8 s.197
• /
• pp.74-80
• /
• 2007

The distortion of printed pattern is frequently observed in gravure offset printing process, which can be a serious problem in printing process for printed electronics. The mechanism of pattern distortion is studied and the factors which affect the amount and shape of distortion are found using FEM. The amount and shape of distortion is influenced by material properties of the roller, thickness of roller, applied load, and so on. As the printing pressure increases and Possion ratio increases, the degree of the image distortion increases. And the increase of the thickness of rubber roller brings a large distortion of image, too. In some cases, the distortion of printed pattern can reach a few hundred micromillimeters. The comparison of the experiment result and the simulation result shows good agreement in their quantitative tendency.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.401-406
• /
• 2013

This paper presents experimental evaluation of IRE (isolation roller bearing) seismic isolation device. From the combination of base isolation on the IRE system displacement response spectrum and acceleration response spectrum, the compressive strength and the coefficient of friction experiments. Also the IRE system is evaluated by environment test according to KS standards. Both the resonance and seismic experiments using a combination of the IRE and Natural Rubber Bearing (NRB) are performed in order to analyze the seismic isolation of the IRE system dynamic characteristics. For the given load and exciting frequency, the resonant frequency becomes lower, but the resonant magnification remains to be same. However, it is shown that when we consider the IRE only, the vibration on the table with the horizontal movement and the independent horizontal displacement due to the rolling motion of the plate and roller are significantly reduced. This result verifies that the proposed optimal design method of the IRE system is very effective.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1496-1499
• /
• 2005

This paper was represented an electrostatics distribution analysis using FEM(finite element method) with industrial type Inkjet plotter. Here, we know electronic value with each system position by experiment. these were decreased by discharge through earth and electricity shielding. According to industrial development, all fields using chemical instrument and material are generated an electrostatics. Based on these, the big large position of electrostatics was obtained metal base of controller, nonconductor fiber between two rubber roller, head controller by moving roller etc., Therefore these were showed an electrostatics generation source and by rubbing and meager profits electric charge.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.7 s.238
• /
• pp.1005-1012
• /
• 2005

An OHT(Over Head Transportation) vehicle is an example of the industrial monorail vehicle, and it is used in the automobile, semiconductor, LCD manufacturing industries. OHT vehicle is moved by main wheels and guide rollers. The major function of the main wheel is to support and drive the OHT vehicle. The roles of the guide roller is the inhibition of derailment and steering of the OHT vehicle. Since the required vehicle velocity becomes faster and the required load capacity is increased, the durability characteristics of the wheel and roller, which was made of urethane, need to be increased. So it is necessary to estimate the fatigue life cycle of the wheel and roller. In this study, OHT dynamic model was developed by using the multi body dynamic analysis program ADAMS. Wheel and roller are modeled by the 3-D surface contact module. Especially, motor cycle tire mechanics is used in the wheel contact model. The OHT dynamic model can analyze the dynamic characteristic of the OHT vehicle with various driving conditions. And the result was verified by a vehicle traveling test. As a result of this study, the developed model is expected to predict wheel dynamic load time history and makes a contribution to design of a new monorail vehicle.

• Earthquakes and Structures
• /
• v.10 no.4
• /
• pp.829-847
• /
• 2016

Generally seismic isolation is achieved by supporting the structure on laminated rubber bearings, friction pendulum bearings, roller bearings etc. Very little work has been performed using soil as a base isolation media. Experiments and analytical work has been performed on a structural model with isolated footing and found encouraging results. Details of this work are presented in this paper.