• Fire Science and Engineering
• /
• v.34 no.1
• /
• pp.18-25
• /
• 2020

In this study, the heat release rate of pipe insulation is analyzed by considering the installation status in accordance with the standards ISO 20632 and NFPA 274. The flame retardation rate was evaluated for six types of test samples: polyethylene foam covered with beaten silver (PE(S)), PE foam tapped (PE(N)), elastomeric closed cell thermal insulation (rubber), Japanese PE foam (PE(J)), Japanese polyurethane foam (PU(J)), and Japanese styro form (ST(J)) by EN 13501-1 and fire growth curve. The results show that PU(J), PE(J), and PE(N) were Class E and ultra-fast, NFPA 274 test standards for Class D and Fast, and PE(S) by ISO 20632 were Class C and Slow, and Rubber and ST(J) were Classes and Low. However, the changes in the time-averaged maximum heat release rate for each test standard (ISO 20632 and NFPA 274) to evaluate the flame retardation rate differed among identical materials. This means that the fundamental study is necessary to analyze the more accurate reasons.

• Clean Technology
• /
• v.27 no.1
• /
• pp.24-32
• /
• 2021

Unburned carbon (UC) was successfully separated from fly ash by up to 85.8% in weight via froth flotation using soybean oil as a collector. An 18 wt% yield of microceramics (CM) could be achieved by employing a hydro cyclone separator located immediately after the flotation equipment. UC and CM were tested as alternatives to weight-adding material and polymer (especially polypropylene in this study) filler, respectively. Large particles of UC were broken down into smaller ones via ball milling to have an average particle diameter of 10.2 ㎛. When crushed UC was used as an alternative to clay as a rubber weight-adding material, a somewhat lower tensile strength and elongation rate than the allowed values were unfortunately obtained. In order to satisfy the standard limits, further treatment of UC is required to enhance surface energy for more intimate bonding with rubber. CM was observed in spherical forms with an average diameter of 5 ㎛. The surface of the CM particles was modified with phenol, polyol, stearic acid, and oleic acid so that the surface modified CM could be used as a polypropylene-filling agent. The flowability was good, but due to the lack of coupling forces with polypropylene, successful impact strength and flexural strength could not be obtained. However, when mixing the surface-modified CM with 1% silane by weight, a drastic increase in both the impact strength and flexural strength were obtained.

• Elastomers and Composites
• /
• v.46 no.1
• /
• pp.29-36
• /
• 2011

The term 'thermal insulating materials' describes a class of materials which can improve the thermal efficiency by reducing the thermal conduction, convention and radiation between the inside and outside of the system. As a thermal insulating material, numerous industrial applications are possible including the automobile, aerospace, aviation, and petrochemical. Especially, the silica aerogel, with their superior thermal insulating behavior, has been widely used as thermal insulating materials. Because the mechanical properties of the silica aerogel cannot meet the industrial demand, use of the silica aerogel is limited. This article aims to review the thermal insulating materials and silica aerogel, and to introduce the silica aerogel/polymer composites.

• The Journal of Korean Academy of Prosthodontics
• /
• v.46 no.2
• /
• pp.105-115
• /
• 2008

Statement of problem: Proper finishing and polishing enhance both the esthetics and the longevity of restored teeth. Blade finishing technique would be suited for smoothing and finishing. Evaluation of this technique are necessary. Purpose: The purpose of this study was to evaluate the blade finishing and polishing procedures on the surface profile and roughness of ormocer-based composite resin and nanohybrid composite resin. Material and methods: The material included a ormocer-based composite resin ($Admira^{(R)}$ & $Admira^{(R)}$ Flow); a nanohybrid composite resin ($Grandio^{(R)}$ & $Grandio^{(R)}$ Flow). One hundred forty specimens of each group were prepared using a mylar strip and randomly divied into blade finishing and rubber polishing groups (n=10). The average surface roughness (Ra) in micrometers was measured and the surface profile was examined by scanning electron microscopy (SEM) (Magnification ${\times}$ 200). The data were analyzed by Mann-Whitney Test at 0.05 significance level. Conclusion: The results of this study indicated that the mylar strip produced the smoothest surface on all materials and among the finishing-polishing methods was not significanct difference (P>0.05). Ormocer-based flowable composite resin performedthe lowest variability in initial surface roughness among the tested materials.

• Elastomers and Composites
• /
• v.43 no.2
• /
• pp.88-103
• /
• 2008

This study was purposed to investigate the effects of surfactants and fillers on physical properties of hydrophilic polyvinylsiloxane dental impression materials (PVS). Incorporation of surfactants enhanced the hydrophilicity of the PVS, however, it induced increased viscosity and permanent deformation ratio, delayed setting, and decreased tensile strength. At high concentrations of surfactant, the tensile strength was observed to decrease significantly due to the internal pore formation. Especially, the hydrophilicity of the PVS was significantly enhanced with the addition of Silwet L-77. However, the viscosity, strain in compression, pore formation, and setting time increased whereas the elastic recovery rate and strength remarkably decreased. The PVS dental materials containing Span 20 showed the lowest degree of viscosity increase, delayed setting, pore formation, and hydrophilicity. The delayed setting, pore formation, and strength decrease caused by the incorporation of surfactant were improved by substituting the crystalline quartz filler with diatomaceous earth while the contact angle of PVS dental materials increased.

• Elastomers and Composites
• /
• v.52 no.1
• /
• pp.22-26
• /
• 2017

The thermal conductivity and the adhesive properties were measured, after synthesis of thermal conductive composite which was obtained as a result of mixing alumina or graphite with acrylic adhesive synthesized by UV polymerization. The adhesive properties of the composite were evaluated measuring the peel strength at 180 degrees, the retention, and the initial tack;the thermal conductivity was estimated using laser flash analysis. As the filler contents increased, a decrease in peel strength and initial tack and an increase in retention and thermal conductivity were observed. When compared to alumina, the adhesion of graphite showed a dramatic decrease, whereas the thermal conductivity was further enhanced. It was found out that the small size of graphite increased the mechanical interlocking between the polymer and the filler, and it was easier for graphite to come into contact with other graphite in the matrix.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.32 no.5
• /
• pp.741-752
• /
• 2008

The purposes of this study are to review the status of dress material in the contemporary fashion design by examining the intertextuality of many materials other than textiles used in the contemporary fashion and to show that the development of new fashion materials is a factor for designing competitiveness. The results of this study are summarized as follows: First, foods and natural objects are used as fashion materials to reveal natural beauty, and at the same time new formative elements are expressed in combinations of life and fashion. Second, common paper and luxurious jewelry are presented as a formative element symbolic of an aspect of the contemporary society or embodied in elaborate handicraft techniques. Those materials boost the luxuriousness of costume and create a strong futuristic image according to how they are expressed. Third, plastics available for a variety of objects in different shapes and colors offer such formative features that could be shaped with textiles, as high-end technology is introduced to fashion. Fourth, metallic materials have added freedom to design formality due to their qualities of convergence and displacement and by the introduction of brand-new technology, suggesting a new future for the fashion industry. Fifth, using a variety of anti-fashion materials including semiconductor chips, mirrors, vinyl, wires, and rubber makes a change in the existing points of view regarding the formality of things and helps create a special aesthetic effect in a visual respect to develop a strong intertextuality of materials.

• Elastomers and Composites
• /
• v.51 no.2
• /
• pp.147-153
• /
• 2016

Polyvinyl chloride (PVC) has been used as a general-purpose polymer because of its lower cost, good durability and mechanical properties compared to other materials. However, PVC is vulnerable to heat deformation and generates a toxic gas like hydrogen chloride. Therefore, it is important to delay or prevent the flame retardancy and thermal degradation of the PVC during the processing. It was reported that aluminum trihydroxide (ATH) improved flame retardancy as well as smoke inhibition of the virgin polymer. In this study, PVC composites by addition of ATH were compounded in a modular intermeshing co-rotating twin screw extruder. The PVC composites with different concentrations of ATH (0~5 phr) were analyzed. Flame retardancy of the PVC composite significantly increased depending on the ATH concentration. LOI of the composite also increased with the concentration of ATH. There were no significant differences for the thermal properties of the PVC composites with ATH.

• Elastomers and Composites
• /
• v.46 no.1
• /
• pp.10-21
• /
• 2011

Recently, with developments in the automotive industry, sound and vibration damping have a considerable attraction with a diversified customer needs and advanced automobile. In general, among various materials, textile materials, such as felt and glass fibers, polyurethane foam, and PET fiber materials were used to reduce sound and vibration of the automobile. These materials were located in various main parts of the automobile to block sound and vibration, resulting in a comfortable ride. In addition, to improve fuel economy, weight reduction and cost saving for the automobile were also being considered together as well as the reduction of sound and vibration of the automobile. Therefore, in this paper, we focused on the need of interior sound and vibration absorption materials in the automobile and absorption materials-related technologies.

• Elastomers and Composites
• /
• v.50 no.3
• /
• pp.223-230
• /
• 2015

Bacterial infection is one of the most common and universal cause of disease spreading associated with medical and surgical environment. Antimicrobial function of plasticized polyvinyl chloride (PVC) will be useful for making hygienic environments. Here, we synthesized the PVC composite by the addition of inorganic bacteriocide containing silver, zinc and zeolite. And we investigated the growth inhibition rate for Staphylococcus aureus and Klebsiella pneumoniae which were analyzed in the presence of PVC composite with different doses of inorganic bacteriocide (1~15 wt%). Bacterial proliferation was significantly inhibited by 3 wt% of inorganic bacteriocide containing PVC composite. And we found the inhibition of bacterial biofilm formation by 5 wt% of inorganic bacteriocide containing PVC composite by the observation of scanning electron microscopy (SEM). Our data suggested that the antimicrobial effect of inorganic bacteriocide was caused by disturbing the bacterial biofilm formation.