• Elastomers and Composites
• /
• 제58권3호
• /
• pp.103-111
• /
• 2023

The abrasion resistances of silica-filled styrene-butadiene rubber (SBR) compounds prepared with and without dicyclopentadiene resin (SBR-R and SBR-0, respectively) were studied using four different abrasion testers, namely cut and chip (CC), Lambourn, DIN, and laboratory abrasion tester (LAT100). The effect of the resin on the abrasion behavior was elucidated by analyzing the morphologies and size distributions of wear particles. All the wear particles had rough surfaces, but those obtained in the Lambourn abrasion test exhibited relatively smooth surfaces. The size distributions of the wear particles showed different trends depending on the abrasion tester and the rubber compound; however, most of the wear particles were larger than 1000 ㎛. The SBR-R sample showed a wide range of particle sizes (from 63 ㎛) in the LAT100 abrasion test and majority of the wear particles were 500-1000 ㎛, whereas the SBR-0 sample had the most distribution of larger than 1000 ㎛. The abrasion rates of SBR-0 sample were lower than those of the SBR-R sample for the CC and LAT100 abrasion tests, but the Lambourn abrasion test result showed the opposite trend. Addition of the resin influenced the abrasion behavior, however the effect varied depending on the type of abrasion tests.

• Elastomers and Composites
• /
• 제42권1호
• /
• pp.20-31
• /
• 2007

고무의 안정성과 신뢰성 확보를 위해 재료 특성과 수명 평가는 매우 중요하다. 본 연구에서는 연료전지용 고무 가스켓으로 사용되는 황으로 가황한 NBR compound의 수명을 예측하였다. 5, 6, 7 vol% 황산농도에서 120, 140, $160^{\circ}C$ 온도로 각각 3시간에서 600시간까지 가속 노화시험을 하였다. 고무를 황산용액 안에 침지시키기 위해 pyrex glass tube를 사용하였다. 그리고 가열 시간 동안 용액의 증발을 막기 위하여 pyrex glass tube 양쪽 끝을 막았다. 연료전지용 가스켓인 NBR 고무의 수명을 예측하기 위하여 가속 산-열 노화시험 후 물성 실험을 하였으며 산-열 노화시험에서 물리적 특성의 영향을 연구하기 위하여 인장강도, 신장율, 경도, 가교밀도를 측정하였다. 인장강도는 황산농도와 온도가 증가함에 따라서 감소되었는데 이 결과로 Arrhenius 식을 유도하여 수명을 평가하였다.

• Carbon letters
• /
• 제10권2호
• /
• pp.101-108
• /
• 2009

Various silanes, amino silane, vinyl silane, TESPD, and ZS (TESPD/zinc soap complex), are added into chlorinated isobutylene-isoprene copolymer (CIIR)/hard clay/carbon black (CB) compound and they are investigated with respect to the vulcanization characteristics, the processability, and the mechanical properties. In hard clay/CB filled system, only ZS silane added compound shows both lower Mooney viscosity and extrusion torque while vinyl silane added compound showed only a lower extrusion torque. All the ZS added compounds showed the lowest viscosity among them. The silane added compounds showed an increased modulus. In 'fatigue to failure' count test, the ZS added compound showed superior counts compared to other silane (amino, vinyl, TESPD) added compounds. The mechanical properties were significantly increased when the S2 and ZS were added into CIIR/hard clay/CB compound. The ZS added compounds showed a significant improvement on elongation modulus.

• 설비공학논문집
• /
• 제13권7호
• /
• pp.627-636
• /
• 2001

This paper presents a numerical analysis of the emission process of volatile organic compound(VOC) from building material and its diffusion in a room. A polypropylene styrene-butadiene rubber(SBR) floor plate is chosen as the emission source of VOC. This study investigates spatial concentration distributions and time history of room-averaged VOC concentration for both with and without flushing. The results of this study show that for calculation based on ten-days period the room averaged VOC concentrations with and without flushing are quite different. the results thus suggest the need of flushing for new buildings.

• 한국소음진동공학회논문집
• /
• 제22권9호
• /
• pp.837-844
• /
• 2012

We considered an approach in terms of materials for improvement of insulation performance of vehicle rubber hoses. Ethylene propylene rubber(EPDM) for heater hoses in cooling system and acrylic rubber(AR) for intercooler hose in intake system were chosen for mixing for the vibration and noise performance. We modified EPDM and AR through changing compound of base polymer, reinforcement fillers and additives. Dynamic mechanical analysis(DMA) was used to measure viscoelastic properties such as shear modulus and loss factor($tan{\delta}$). Vehicle acceleration test was also conducted to observe indoor changes in insulation performance of hoses.

• Elastomers and Composites
• /
• 제51권3호
• /
• pp.218-225
• /
• 2016

In order to examine correlation between silane coupling agent and activator which affects the physical properties of silica filled natural rubber compound, such as heat buildup, rebound property, dynamic mechanical and morphological properties were measured. With incorporation of silane coupling agent, $tan{\delta}$ at $0^{\circ}C$ was increased and at $60^{\circ}C$ was decreased, which resulted in improving of wet grip and rolling resistance. When silane coupling agent which is corresponding to 8~10% of silica was used, most favorable heat build up and $tan{\delta}$ was obtained. And also when activator was used, dispersibility of silica was improved as a result of reduction of reaggregation of silica.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.206-209
• /
• 2002

The purpose of this research was to find influence of compounding materials on electrical properties of silicone rubber such as tracking characteristic. The tracking characteristic was tested through controlling the ATH, a widely use anti-tracking agent. Regarding the particle size and coupling agent of ATH, compound silicone rubber with ATH of coupling agent and larger diameter showed better anti-tracking properties. It can be included that ATH of coupling agent use vinyl silane, dispose of tracking characteristic was achieve excellant results.

• 폴리머
• /
• 제38권5호
• /
• pp.664-670
• /
• 2014

The effects of different filling materials and stabilizers in polymer based materials that are used as shoe soles in the shoemaking industry on the mechanical properties (strength, failure, tensile, tearing, bending etc.) of the final products have been examined in this study. Natural rubber (NR RSS3) and styrene-butadiene rubber (SBR 1502) were used as the main matrix material. New compounds were formed by replacing the fillings in the general compound of the existing factory ($SiO_2$, $CaCO_3$) with 40% (1200 g) blast furnace flue dust, rice husk, reclaimed rubber (recycled) and wood ash. Comparison of the new compounds with the existing compounds revealed a decrease in hardness, density, dimension stability, bending, tearing, % elongation and failure strength and an increase in wearing.

• Elastomers and Composites
• /
• 제38권2호
• /
• pp.167-174
• /
• 2003

Thermoplastic vulcanizates (TPV) or dynamic vulcanizates are thermoplastic elastomers produced by simultaneous mixing and crosslinking of a rubber and a thermoplastic. The objective of the present work is to investigate the effects of different types of peroxides as curing agents on the properties of PP/EPDM TPVs. The mechanical properties change significantly with the chemical nature of the peroxides and the extent of crosslinking at a fixed PP/EPDM blend ratio. The tensile strength of the TPVs obtained with the various peroxides can be related to the solubility parameters of the polymers and of the peroxides. The Young's modulus of the peroxide-cured TPVs can be correlated with the delta torque values of equivalent thermoset EPDM vulcanizates, corresponding to the crosslinking efficiencies of the peroxides.

• 대한기계학회논문집A
• /
• 제34권8호
• /
• pp.1045-1050
• /
• 2010

고무부품의 신뢰성을 확보하기 위해서는 피로수명예측 및 평가기술 개발이 중요하다 하겠다. 최근에 고무부품에 대한 고성능, 고신뢰성을 위해 설계, 해석 및 평가기술이 요구되고 있으나, 지금까지는 경험과 시행착오적인 방법으로 개발되고 있는 실정이다. 따라서, 본 연구에서는 고무소재에 대해 배합조건, 기계적 특성, 열화 및 피로수명 등을 포함하는 고무소재 물성 데이터베이스를 구축하고, 고무부품의 특성해석 결과를 데이터베이스와 연계하여 고무부품의 피로해석 모델을 개발하였으며, 실제 피로시험 결과를 통하여 개발된 모델의 타당성을 검증하였다.