• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.413-416
• /
• 2006

PtRu catalyst is most widely used as anode catalyst for a direct methanol fuel cell(DMFC). To promote the efficiency of the catalysts, it Is important to increase the triple phase boundary. In this study, we have tried to increase the triple phase boundaries in preparing electrocatalysts of the fuel cells, based on the process of grafting a proton-conducting agent onto the catalyst This grafted proton-conducting agent can act as an ionomer like Nafion, currently widely used ionomer. First, we have prepared the 80wt% PtRu/Ketjen Black electrocatalyst by an improved colloidal method. And, we have grafted methylsulfonate groups $(-CH_2SO_3H)$ into the catalyst as proton-conducting agents. As results of cyclic voltammety and single cell test of the membrane electrode assembly (MEA), we can conclude that the activity of the grafted electrocatalysts is superior to that of conventional ones, in performance of DMFCs. For our further study, we will investigate the optimum ratio of catalyst/grafted proton conduct Ing agent with maximum performance of a DMFC.

• Transactions of the Korean hydrogen and new energy society
• /
• v.15 no.2
• /
• pp.137-143
• /
• 2004

For hydrogen generation from aqueous alkilne $NaBH_4$ solution, Co-B catalyst was prepared by chemical reduction method using $NaBH_4$ as a reduction chemical. Effects of solution temperature, amount of catalyst loading, $NaBH_4$ concentration, and NaOH (a base-stabilizer) concentration on the hydrogen generation rate were exmanined. Compared to Ru catalyst generally used, the low-cost Co-B catalyst exhibited almost comparable activity to the hydrogen generation reaction.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.5
• /
• pp.471-477
• /
• 2016

In this research, the Ir supported $TiO_2$ (P25) catalyst was prepared by precipitation method for oxygen evolution reaction. The $Ir/TiO_2$ catalyst was synthesised by reduction reaction using reducing agent. Physiochemical characterizations of synthesized $Ir/TiO_2$ catalyst was studied by means of SEM, EDS mapping, TEM and XRD. The Electrochemical characterizations were tested by using the technique of CV and LSV by RDE and Potentiostat. Physicochemical properties were characterized with XRD where Iridium metal morphology and Ir(111) and Ir(222) peaks were founded. $Ir0.2Ru0.8O_2$ exhibited higher OER activity than $Ir0.5Ru0.5O_2$ followed by $Ir/TiO_2$ and $IrO_2$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.157.1-157.1
• /
• 2011

선택적 CO 산화반응(PrOx)에 사용되는 촉매 중 Pt, Ru, Rh 등의 귀금속 계 촉매들은 비귀금속 계 촉매에 비해 활성이 좋은 반면 가격이 비싸다는 경제적인 제한점이 있다. 따라서 소량의 귀금속을 사용하여 높은 활성의 촉매를 제조하고자 활성금속의 고분산 담지 방법에 대한 연구가 이루어지고 있다. 본 연구에서는 담체인 ${\gamma}-Al_2O_3$ 표면에 활성금속인 Pt의 고분산 담지를 위해 증착-침전법(Deposition-precipitation)을 적용하였으며 용액의 pH 변화에 따른 Pt 금속 입자의 분산도에 대한 영향을 살펴보았다. Pt의 함량은 1wt%로 고정하였고 침전제로 NaOH를 사용하여 용액의 pH를 pH 7.5 ~ 10.5로 변화시켰다. 제조된 촉매는 세척 후 $400^{\circ}C$, 3시간 소성 하였다. 제조된 1wt% Pt/$Al_2O_3$ 촉매의 특성분석을 위해 BET, TPR, CO-chemisorption을 수행하였다. PrOx 반응 실험은 GHSV=60,000 $ml/g_{cat}{\cdot}h$, $T=100{\sim}200^{\circ}C$, ${\lambda}$=4 조건에서 수행되었으며 반응 전에 촉매는 $400^{\circ}C$, 3시간 환원 후 사용하였다. 촉매의 특성분석과 PrOx 반응 실험 결과를 통해 촉매가 담체 위에 고분산 되는 최적의 pH를 확인할 수 있었으며, 기존의 함침법으로 제조된 촉매와 성능 비교를 통해 제조방법에 따른 영향을 살펴보았다.

• Applied Chemistry for Engineering
• /
• v.28 no.5
• /
• pp.593-596
• /
• 2017

Sodium titanate nanosheets were prepared by a hydrothermal synthesis method under basic conditions. Ruthenium was introduced on the surface of sodium titanate nanosheets through an UV irradiation in the aqueous $RuCl_3$ solution. The crystal phase and morphology of synthesized samples were analyzed by X-ray diffraction, transmission electron microscopy and energy dispersive spectroscopy. In addition, the content of Ru was evaluated by inductively coupled plasma. It was proposed that a monomeric form of ruthenium was incorporated on the surface of sodium titanate. Ruthenium incorporated sodium titanates were applied to alcohol oxidation using molecular oxygen as an oxidant. The sample with 7% ruthenium showed a catalytic activity with a turnover frequency value of $2.1h^{-1}$ in oxidizing benzyl alcohol to benzaldehyde without any other byproducts at $105^{\circ}C$ and 1 atmosphere.

• Transactions of the Korean hydrogen and new energy society
• /
• v.25 no.5
• /
• pp.459-467
• /
• 2014

The catalytic steam reforming of toluene, a major component of biomass tar, was studied using several catalysts at various temperatures $400-800^{\circ}C$, kind of metal, and metal loading content. Ru and K promoted Ni-base catalyst were prepared, and used for steam reforming of toluene with steam/toluene molar ratio of 25. Concentration of toluene in reactant flow is $30g/Nm^3$ that is usual content of tar from biomass gasifier. The result from experiments showed that $H_2$ content in product gas and toluene conversion increased with temperature. Where in high temperature range, CO and $CO_2$ content in product gas were affected mainly by Boudouard reaction. Ni/Ru-K(3wt%)/$Al_2O_3$ catalyst showed best performance on steam reforming of toluene than used catalysts in this study at whole temperature. Catalysts have been characterized by XRD, TG. XRD analysis displayed that Ni particle size on Ni/Ru-K (3wt%)/$Al_2O_3$ catalyst was 29.4nm. Activation energy of Ni/Ru-K (3wt%)/$Al_2O_3$ catalyst was calculated 36.8kJ/mol by Arrhenius plot.

• Journal of Korean Society of Water and Wastewater
• /
• v.31 no.5
• /
• pp.397-407
• /
• 2017

A dimensionally stable anode based on the $RuO_2$ electrocatalyst is an important electrode for generating chlorine. The $RuO_2$ is well-known as an electrode material with high electrocatalytic performance and stability. In this study, sonoelectrodeposition is proposed to synthesize the $RuO_2$ electrodes. The electrode obtained by this novel process shows better electrocatalytic properties and stability for generating chlorine compared to the conventional one. The high roughness and outer surface area of the $RuO_2$ electrode from a new fabrication process leads to increase in the chlorine generation rate. This enhanced performance is attributed to the accelerated mass transport rate of the chloride ions from electrolyte to electrode surface. In addition, the electrode with sonodeposition method showed higher stability than the conventional one, which might be explained by the mass coverage enhancement. The effect of sonodeposition time was also investigated, and the electrode with longer deposition time showed higher electrocatalytic performance and stability.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.4
• /
• pp.279-282
• /
• 2007

When reformer for fuel cell is used, CO in hydrogen gas leads to a seriously decreased membrane electrode assembly (MEA) performance by catalyst poisoning. The effect of CO on performance of modified MEA by sputtering method is studied in this paper. The experimental results show that sputtered Pt and Ru thin film improve a single cell performance of MEA and sputtered metal thin film has a CO tolerance. The air injection process on anode show improved CO tolerance test result. Moreover, Pt, Ru and PtRu thin film by sputtering had influence on the CO tolerance with air injection process.

• Applied Chemistry for Engineering
• /
• v.10 no.7
• /
• pp.1079-1085
• /
• 1999

An investigation was made of the effect of various transition metal catalysts, ligands, and a promoter on the synthesis of N,N'-diphenylurea(DPU) from nitrobenzene, aniline, and carbon monoxide. Homogeneous Pd and Ni catalysts were found to be highly efficient, giving almost quantitative isolated DPU yields at 100% nitrobenzene conversion. Bidentate ligand, 1,3-bis(diphenylphosphino)proane(dppp) showed much improved activity and significantly different reactivity relative to the usual monodentate $PPh_3$ ligand in the presence of Ni and Pd catalysts. These results were inferred to the effect of the cis coordination of bidentate dppp ligand on the metal. The use of a promoter $Et_4NCl$ was indispensable in the case of $PPh_3$, yet inhibited the reaction if used with dppp. It was possible to reuse the Pd-dppp catalyst system, although the catalytic activity was reduced slowly.

• Applied Chemistry for Engineering
• /
• v.21 no.1
• /
• pp.81-86
• /
• 2010

On adsorbing carbon monoxide (CO) on the silica supported ruthenium/iron alloy ($Ru/Fe-SiO_2$) samples above mole ratio 9/1 of Ru/Fe five bands ($2138.7{\sim}2142.5cm^{-1}$, $2067.3{\sim}2073.1cm^{-1}$, $1976.7{\sim}2017.2cm^{-1}$, $1737.9{\sim}1799.3cm^{-1}$, $1625.7cm^{-1}$) were observed, and in $Ru/Fe-SiO_2$ samples below mole ratio 8/2 of Ru/Fe two bands ($1934.0{\sim}1990.2cm^{-1}$, $1625.7cm^{-1}$) were observed. The $2138.7{\sim}2142.5cm^{-1}$ bands, the $2067.3{\sim}2073.1cm^{-1}$ bands, and the $1988.3{\sim}2030.7cm^{-1}$ bands may be ascribed to stretching vibrations of CO molecules lineally bonded to the Ru atoms on supported Ru/Fe cluster surface, the $1737.9{\sim}1799.3cm^{-1}$ bands to stretching vibrations of CO molecules bridge bonded to the Ru atoms on supported Ru/Fe cluster surface or to stretching vibrations of CO molecules bonded to the Ru atoms on high Miller index planes, and the $1934.0{\sim}1990.2cm^{-1}$ bands to stretching vibrations of CO molecules lineally bonded to the Fe atoms on supported Ru/Fe cluster surface. The absorbances of the $1934.0{\sim}1990.2cm^{-1}$ bands in $Ru/Fe-SiO_2$ samples gradually increased with the increases of Ru/Fe mole ratio below the ratio of 8/2. This phenomena may be ascribed to the increases of Fe concentration of surface compared with the one of the sample and to the increases of surface area of supported Ru/Fe cluster according as increase of Ru/Fe mole ratio below the ratio of 8/2 compared with the $Fe-SiO_2$ sample.