• 설비공학논문집
• /
• 제12권1호
• /
• pp.50-58
• /
• 2000

Experiments were carried out to obtain the effects of nozzle configuration and jet to jet spacing on the heat transfer characteristics of single line of circular water jets impinging on a constant heat flux plane surface. The nozzle configurations are Cone type, Reverse cone type and Vertical circular type, and the nozzle arrays are single jet(nozzle dia. 8 mm), 1 row of 3 jets and 1 row of 5 jets. Jet velocities ranging from 3m/s to 8m/s were investigated for the nozzle to target plate spacing of 80 mm. For the Cone and Reverse cone type nozzle arrays, the average Nusselt number of 1 row of 5 jets was larger than that of 1 row of 3 jets at Re$_{D}$<45000, but that of 1 row of 3 jets was larger than that of 1 row of 5 jets at $Reo\le45000$. For the Vertical circular type nozzle, however, the average Nusselt number of 1 row of 3 jets was larger than that of 1 row of 5 jets at all jet velocities. In the condition of fixed mass flow rates, the maximum heat transfer augmentation was obtained for 1 row of 5 jets and was over 2 times larger than that of the single jet for all nozzle configurations. The nozzle configurations that produce the maximum average Nusselt number are as follows: For 1 row of 3 jets, the Vertical circular type at $Reo\le45000$ and the Reverse cone type at $Reo\le45000$. But, they are the Reverse cone type at Re$_{D}$<55000 and the Vertical circular type at$Reo\le55000$ for 1 row of 5 jets.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.215-218
• /
• 2005

로켓엔진 연소기의 분사면 냉각성능을 개선하기 위한 연료 매니폴드의 최적형상을 제시하였다. 매니폴드의 형상은 분사균일성을 최대한 유지하면서 분사면 중심의 냉각성능을 높일 수 있어야 한다. 이를 위하여 7가지 후보 형상에 대하여 냉각성능을 비교한 결과 분사기 2-3열과 9-10열 사이에 분할 판이 설치된 형상이 최적인 것으로 판단된다. 분사균일성은 설계원형과 유사한 수준이며 분사면의 최고온도는 $27\%$ 감소하였다. 또한 매니폴드의 형상 변화에 의한 추가적인 압력강하는 거의 없을 것으로 예측되었다.

• Steel and Composite Structures
• /
• 제27권6호
• /
• pp.727-745
• /
• 2018

The design criteria and the corresponding performance levels characterize the response of extended stiffened end-plate beam-to-column joints. In order to guarantee a ductile behavior, hierarchy criteria should be adopted to enforce the plastic deformations in the ductile components of the joint. However, the effectiveness of thesecriteria can be impaired if the actual resistance of the end-plate material largely differs from the design value due to the potential activation of brittle failure modes of the bolt rows (e.g., occurrence of failure mode 3 in the place of mode 1 per bolt row). Also the number and the position of bolt rows directly affect the joint response. The presence of a bolt row in the center of the connection does not improve the strength of the joint under both gravity, wind and seismic loading, but it can modify the damage pattern of ductile connections, reducing the gap opening between the end-plate and the column face. On the other hand, the presence of a central bolt row can influence the capacity of the joint to resist the catenary actions developing under a column loss scenario, thus improving the joint robustness. Aiming at investigating the influence of these features on both the cyclic behavior and the response under column loss, a wide range of finite element analyses (FEAs) were performed and the main results are described and discussed in this paper.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2005년도 동계학술발표대회 논문집
• /
• pp.274-280
• /
• 2005

The objective of this study Is to investigate the heat transfer performance of plate discrete fin-and-tube heat exchangers with large fin pitch. In this study, twenty-two heat exchangers were tested with a variation of fin pitch, number of tube row, longitudinal tube pitch and fin alignment. Discrete fin type exchangers improved heat transfer performance more than 10% compared to tile continuous fin type heat exchangers. The air-side heat transfer coefficient decreased with a reduction of the fin pitch and an increase of the number of tube row, The staggered fin alignment improved heat transfer performance more than 6% compared to the inline fin alignment. The effect of longitudinal tube pitch was insignificant on the j-factor and experiments found opposite effects on the j-factor with respect to fin alignment. Heat transfer correlations were developed from the measured data for flat plate discrete fin-and-tube heat exchangers with large fin pitch. The correlations yielded good predictions of the measured data with mean deviations of 1,4% and 0.3% for tire inline and staggered tube alignment, respectively.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1098-1103
• /
• 2004

In this study, the effect of channel flow in the concave surface on local heat transfer characteristics of array jets was investigated experimentally. A TLC method is employed to determine local heat transfer coefficients on the target plate and also flow visualization has been conducted to investigate the behavior of a row of impinging jets and array of impinging jets. Two different array patterns of impinging array jets devices are tested for Reynolds number(Re=10,000). In a row of impinging jets, secondary vortex is strongly maintained by main vortex at nozzle-to-plate distance of H/d=2. Therefore, the Nusselt number slowly decreased at the mid-way region between adjacent jets. In array jets, the local maximum Nusselt number region move further in the downstream direction due to the increase of channel flow velocity.

• 대한인간공학회지
• /
• 제14권2호
• /
• pp.15-24
• /
• 1995

The purpose of this study is to provide ergonomic research data for the redesign of the car license plate in Korea. Several alternatives having various combinations of fonts, stroke-width ratios, color contrasts, and arrays were considered in order to find the best one in terms of the reading-distance and the misreading-rate. Experiments investigating the reading-distance, misreading-rates were conducted. In addition, the alternatives were tested in a real driving situation. The results can be summarized as follows : The typography having mixed type numeric forms with quasi-Gothic and NAMEL, stroke-width ratio of 1:7 .approx. 1: 8, the black on yellow contrast showed a good reading-distance. The array with Hangul(showing territorial office and use-sign) at the upper row and 6 mumbers ( showing car class-sign and serial number) at the lower row showed relatively low misreading-rate.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2001년도 춘계학술대회 논문집
• /
• pp.65-69
• /
• 2001

In this paper, consider the three cases of decide for appling point a general Simple Genetic Algorithm about heuristic method(Bottom and Left Sliding) at the piece auto-nesting on the row plate. The 1st case, about only using the Simple Genetic Algorithm. The 2nd case, applied the heuristic method to the genetic operating of the Simple Genetic Algorithm. The 3rd case, applied the heuristic method to the final result of the Simple Genetic Algorirhm. The estimation of final result were proceed to developed simulation program in this research.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.53-56
• /
• 2009

Roll forming process is one of important metal processing technology because the process is simple and economical. These days, roll forming process is tried to be employed in manufacturing the circuit board, barrier ribs and solar cell plate for productivity. However, it is difficult to apply to the forming of micro scale or sub-micro scale pattern. In this study, the roll forming processing for the micro scale is designed and analyzed. In this study, the forming of micro pattern for solar cell plate by incremental roll forming process is analyzed. The solar cell plate may have thousands of patterns, and the analysis of forming considering all the patterns is impossible due to the computational costs. In this study, analyses are carried out for various numbers of patterns and the results are compared. It is shown that the analyses results with four row patterns and twelve row patterns are same. So, it is considered that the analysis can be carried out for only four rows of pattern for the design of incremental roll forming process. Also experiment is carried out process that is designed through simulation.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.56-59
• /
• 2009

Roll forming process is one of important metal processing technology because the process is simple and economical. These days, roll forming process is tried to be employed in manufacturing the circuit board, barrier ribs and solar cell plate for productivity. However, it is difficult to apply to the forming of micro scale or sub-micro scale pattern. In this study, the roll forming processing for the micro scale is designed and analyzed. In this study, the forming of micro pattern for solar cell plate by incremental roll forming process is analyzed. The solar cell plate may have thousands of patterns, and the analysis of forming considering all the patterns is impossible due to the computational costs. In this study, analyses are carried out for various numbers of patterns and the results are compared. It is shown that the analyses results with four row patterns and twelve row patterns are same. So, it is considered that the analysis can be carried out for only four rows of pattern for the design of incremental roll forming process.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 Ⅲ
• /
• pp.1291-1294
• /
• 2003

This paper presents an approach to extract license plates from parking regulation images which is captured in various photographing direction and complex background. first, we search each row at regular intervals starting from the bottom of a license-plate image, and we set up a rough region for a certain zone in which the sign of intensity vector changes frequently enough and color of license plate is detected enough, assuming it as a candidate location of a license plate. And then, we extract an elaborate area of a license plate by horizontally and vertically projecting vertical edges. Here, tar types of the private and the public, are easily classified according to the color of extracted plates. To evaluate proposed method, we used 200 actual regulation images. As a result, the proposed method showed extraction rate of 96%, which is 9% higher than the previous method using only intensity vector.