• Journal of Biosystems Engineering
• /
• v.19 no.3
• /
• pp.175-184
• /
• 1994

This study was conducted to investigate experimentally the basic characteristics of the torque of the cutterbar driving shaft as the double-knife was used instead of the conventional standard single-knife type. A new design for inclined setting of the cutterbar relative to the direction perpendicular to combine harvester movement was investigated to test a possible reduction of concentrated load caused by the simultaneous cutting of many rows. It was evaluated that the maximum torque and mean total power of the driving shaft due to the cutting resistance of the rice straw were largely depended upon the rotational shaft-speed and straw feeding rate, but were resepectively 1.1~2.3 and 1.15~1.34 times higher compared to those while idling. It was also proved that the inclined setting of the cutterbar could save a considerable amount of energy required for its driving shaft.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2008.09a
• /
• pp.62-67
• /
• 2008

The hovercraft is the amphibious hovercraft. Design and manufacturing companies of the aero propeller exist rarely in the world. Hence the propeller has beef designed and manufactured by manufacturing companies which make aero propeller mainly. In this paper, the hovercraft propeller of similar, which is building and designing by HHIC, is considered the type of aero propeller, rotational speed, diameter, number of blades, Open air propeller efficiency. As the result of check, hovercraft which is necessary huge static thrust is needed the ducted propeller in order to improve climbing capacity. However, the number of blades and turning direction almost do not affect.

• 연구논문집
• /
• s.33
• /
• pp.89-97
• /
• 2003

A barrel cam is used as a very important part of an index drive unit. The index drive unit must have an intermittent-rotational motion. The barrel typed cam and roller gear mechanism has the advantages of high reliability to perform a prescribed motion of a follower. This paper proposes a new method for the shape design of the barrel cam and also a CAD program is developed by using the proposed method. As defined in this paper, the relative velocity method for the shape design calculates the relative velocity of the follower versus cam at a center of roller, and then detemines a contact point by using the geometric relationships and the kinematic constraints, where the direction of the relative velocity must be parallel to a common tangential line at the contact point of two independent bodies, i.e. the cam and the follower. Then, the shape of the cam is defined by the coordinate transformation of the trace of the contact points. This paper presents shape design of the barrel cam in order to prove the accuracy of the proposed methods

• Korean Journal of Applied Biomechanics
• /
• v.20 no.2
• /
• pp.117-127
• /
• 2010

The axes of upper forearm coordinate system have been considered as principal axis of each segment which was component of elbow joint. The purpose of this study was to verify whether the mean direction(principal axis) of instantaneous axes of rotation for pure flexion/extension motion coincided with the flexion/extension axis of upper forearm coordinate system. The same procedure was done for pronation/supination motion. Furthermore, it was tested indirectly that there was an interaction effect between the two rotational motions. The results showed that most segment coordinate axes statistically were not consistent with the mean directions of flexion/extension and pronation/supination axes of rotation. From the results, it would be concluded that the ISB coordinate systems was proved to be a little valid for human movement analysis. There also was an effect of pronation/supination angles on flexion/extension motion.

• Proceedings of the KOSOMBE Conference
• /
• v.1995 no.05
• /
• pp.215-220
• /
• 1995

In this paper, we study myoelectric signal variation through kyungrak needle stimulation. The signal are detected from two kyunrak route of arm; before and after stimulation of a needle, and before and after needle rotation. The detected signals are analyzed at frequency domain to search a characteristic parameters. At the rotation method, spectrum denity of the signals varies large but spectrum is not detected before and after rotation. We can not see any relation bet ween spectrum variation and rotational direction. As the results, when the same stimulation method is used at two different kyungrak route respectively, it is found that the variation of the myoelectric signal is not same.

• The Bulletin of The Korean Astronomical Society
• /
• v.38 no.1
• /
• pp.50.1-50.1
• /
• 2013

As part of the DIGIT key program, we observed GSS30-IRS1, a Class I object located in Ophiuchus (d=125 pc), with Herschel-PACS. More than 70 lines were detected: CO lines of $J=14{\rightarrow}13$ to $41{\rightarrow}40$, several $H_2O$ lines of Eu=100 to 1500 K, 16 OH lines, and two atomic [OI] lines at 63 and 145 ${\mu}m$. All lines, except for [OI], were detected only at the central spaxel of $9.4^{\prime\prime}{\times}9.4^{\prime\prime}$ while the [OI] emission is extended along the NE-SW direction. One interesting feature in GSS30-IRS1 is that the continuum is extended beyond PSF, unlike the line emission. For detail analysis, we apply the non-LTE LVG model, RADEX as well as simple rotational diagrams to the detected line fluxes. We will discuss about the physical conditions around GSS30-IRS1, learned by the line flux analysis.

• Journal of The Korean Astronomical Society
• /
• v.4 no.1
• /
• pp.1-8
• /
• 1971

The average velocity, 330km/sec. of the high velocity stars with respect to the galactic center is obtained from the data used by Fricke on the assumption that the rotational velocity of the Local Standard of Rest is 250km/sec. Comparing this value with the escape velocity, 380km/sec, at the solar neighborhood which is calculated from Mestel's model of the Galaxy, it is shown that most of the high velocity stars are bound to the Galaxy and that their average apogalacticon is about 40 kpc from the galactic center. And the fact that stars with radial velocities larger than 63km/sec are missing in the direction of galactic rotation of L.S.R. is interpreted as the result partly of the random distribution of the directions of motion of the high velocity stars and partly of the observational errors.

• Structural Engineering and Mechanics
• /
• v.49 no.6
• /
• pp.727-743
• /
• 2014

Geometrically nonlinear analysis of planar beam and frame structures made of functionally graded material (FGM) by using the finite element method is presented. The material property of the structures is assumed to be graded in the thickness direction by a power law distribution. A nonlinear beam element based on Bernoulli beam theory, taking the shift of the neutral axis position into account, is formulated in the context of the co-rotational formulation. The nonlinear equilibrium equations are solved by using the incremental/iterative procedure in a combination with the arc-length control method. Numerical examples show that the formulated element is capable to give accurate results by using just several elements. The influence of the material inhomogeneity in the geometrically nonlinear behavior of the FGM beam and frame structures is examined and highlighted.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.2
• /
• pp.153-161
• /
• 1998

This study describes the results of the analysis of measured rotating stall signal in a centrifugal compressor with vaneless diffuser. Unsteady flow and rotating stall in vaneless diffuser were investigated by measuring of unsteady velocity fluctuation using hot-wire anemometer. Experiments were carried out in several impeller rotating speeds, at different radius ratios. Single hot -wire was used to study the characteristics of rotating stall. As a result, the abrupt rotating stall was detected at all measured impeller rotating speeds and the several flow coefficients which are less than 0.16. The number of the stall cell was one at all measured rotational speeds, and the rotating direction was the same as that of the impeller. As the flow rate decreased, the profile of the phase averaged radial velocity component with time changed from a sawtooth to a sine wave.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.804-809
• /
• 2004

This paper introduces a link-type tracked vehicle which is developed for demining operations. The vehicle consists of three parts - front frame, rear frame and body. The front frame is connected to the rear frame by a rotational passive adaptation mechanism which is a driving mechanism of the vehicle. Additionally, the demining system which is adaptable to mobile robot is developed to clear small Anti-Personnel(AP) mines with inexplosive method. In other words, assembled rakes unearth mines by their opposite rotation to the direction of the robot. Finally, the motions of demining rakes and design parameters of the demining system are analyzed.