• Tribology and Lubricants
• /
• v.21 no.5
• /
• pp.201-208
• /
• 2005

This paper presents the FEM analysis on the contact behavior characteristics of mechanical face seals in a small hydro-power turbine. Especially, the axial displacement and contact normal stress between a seal ring and a seal seat of a primary sealing unit have been analyzed as functions of rotating speed of a hydro-turbine, sealing gap, water and cooling fluid temperature. Those are strongly related to a leakage of water and wear between a seal ring and a seal seat. The FEM computed results present that the rotating speed of a hydro-turbine may be kept less than 800 rpm, and the sealing gap in a primary sealing unit is restricted $0.5\~5$. The coolant temperature in which is most influential parameter to the contact behaviors of a sealing unit may be kept less than $15^{\circ}C$ for a safe operation of a sealing unit without a leakage and wear.

• Journal of Astronomy and Space Sciences
• /
• v.28 no.4
• /
• pp.345-354
• /
• 2011

Earth acquisition is to solve when earth can be visible from satellite after Sun acquisition during launch and early operation period or on-station satellite anomaly. In this paper, the algorithm and test result of the Communication, Ocean and Meteorological Satellite (COMS) Earth acquisition are presented in case of on-station satellite anomaly status. The algorithms for the calculation of Earth-pointing attitude control parameters including those attitude direction vector, rotation matrix, and maneuver time and duration are based on COMS configuration (Eurostar 3000 bus). The coordinate system uses the reference initial frame. The constraint calculating available time-slot to perform the earth acquisition considers eclipse, angular separation, solar local time, and infra-red earth sensor blinding conditions. The results of Electronics and Telecommunications Research Institute (ETRI) are compared with that of the Astrium software to validate the implemented ETRI software.

• ETRI Journal
• /
• v.35 no.3
• /
• pp.448-458
• /
• 2013

This paper presents a generalized post-processing technique for enhancing the pseudorandomness of digital chaotic oscillators through a nonlinear XOR-based operation with rotation and feedback. The technique allows full utilization of the chaotic output as pseudorandom number generators and improves throughput without a significant area penalty. Digital design of a third-order chaotic system with maximum function nonlinearity is presented with verified chaotic dynamics. The proposed post-processing technique eliminates statistical degradation in all output bits, thus maximizing throughput compared to other processing techniques. Furthermore, the technique is applied to several fully digital chaotic oscillators with performance surpassing previously reported systems in the literature. The enhancement in the randomness is further examined in a simple image encryption application resulting in a better security performance. The system is verified through experiment on a Xilinx Virtex 4 FPGA with throughput up to 15.44 Gbit/s and logic utilization less than 0.84% for 32-bit implementations.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.3
• /
• pp.93-98
• /
• 2011

In this paper, we propose a game type cognitive rehabilitation system using marker-based augmented reality system for intelligence development of user. Existing cognitive rehabilitation with the help of others, or a keyboard or mouse operation required to relieve the discomfort, the marker card only control it led and is advanced the method which it applied. As a result, obtained through the camera calibration for image processing, and a Augmented Reality as well as mark detection. In this paper we presented a complete rotation of the model after checking through the whole form, through a combination of multiple markers by completing the interactive objects proceed with the rehabilitation process in a manner required by the target of interest to human rehabilitation and treatment.

• Physical Therapy Korea
• /
• v.21 no.1
• /
• pp.55-62
• /
• 2014

For professional drivers, there is a possibility to have musculoskeletal disorders on ankle joint due to repetitive pedaling operation. Therefore, this study have focused to examine ankle active range of motion (AROM), dorsiflexor strength, and pressure pain threshold (PPT) of tibialis anterior muscle (TA) in taxi drivers compared to a age-matched control group. Thirty male taxi drivers with at least 10 years of driving experience and thirty male sedentary workers were evaluated for ankle AROM, dorsiflexor strength, and PPT of TA. Multiple independent t-tests were used to identify significant differences between two groups. For the results, taxi drivers had significantly less AROM in dorsiflexion and greater AROM in external tibial rotation compared to the control group. Also, dorsiflexor strength and PPT of TA in taxi drivers was significantly lower than in the control group. This study indicates that the repetitive ankle movements associated with driving have an effect on ankle AROM, dorsiflexor strength, and PPT of TA and may lead to work-related musculoskeletal disorders on ankle. Professional drivers may need to be educated to prevent a potential musculoskeletal disorders associated with repetitive movement.

• Journal of Power System Engineering
• /
• v.21 no.5
• /
• pp.20-28
• /
• 2017

The steady-state, incompressible and three-dimensional numerical analysis was performed to investigate the flow fields around the seabed tiller used for soil improvement in coastal fisheries and the pulling force and buoyancy generated by tiller operation. The turbulence model used in this study is a realizable $k-{\varepsilon}$. As a results, at a stationary current or a current speed of 1.2 knots, where rotor rotates in a clockwise direction, a typical vortex pair appears near the tip of the rotor except for the edge, and the strength of the vortex pair increases with the number of revolutions of the rotor. The pulling force of the tiller rotating in the counterclockwise direction increases with the number of revolutions. Also, when the current flows at 1.2 knots and the rotor rotates clockwise, the pulling force of the tiller acts on the upstream side irrespective of the number of rotations of the rotor, so that no force is applied. The buoyancy of the tiller acts on the seawater surface if the flow direction inside the rotor is the same as the direction of rotation of the rotor, regardless of the current velocity, otherwise it acts on the seabed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.5
• /
• pp.1183-1192
• /
• 1993

Since the punching time is strongly related to the productivity in sheet metal stamping, there have been a lot of efforts to obtain the optimal tool path. However, most of the conventional efforts have the basic limitations to provide the global optimal solution because of the inherent difficulties of the NP hard combinatorial optimization problem. The existing methods search the optimal tool path with limiting tool changes to the minimal number, which proves not to be a global optimal solution. In this work, the turret rotation time is also considered in addition to the bed translation time of the NCT machine, and the total punching time is minimized by the simulated annealing algorithm. Some manufacturing constraints in punching sequences such as punching priority constraint and punching accuracy constraint are incorporated automatically in optimization, while several user-interactions to edit the final tool path are usually required in commercial systems.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.54 no.1
• /
• pp.26-32
• /
• 2005

Rotor position information is essential in the operation of the switched reluctance motor(SRM) drive for generation the phase current switching signals. When an incremental encoder is used as a rotor position sensor, the initial rotor position can not be detected. Some sensorless rotor position estimation methods also have the same problem. In these systems, to initially align the rotor, the forced alignment method has a delay and reverse rotation before the motor can start. Therefore it can not be acceptable for unidirectional drive systems. So the forced alignment method is not desirable in all drive systems and the research on the SRM drives should be directed to a system without rotor alignment. In this paper, a new detection method of initial rotor position using the rate of change of current is suggested. Firstly, di/dt versus θ/sub R/ reference table, which is the relation between the rate of change of current and rotor position, is generated and then the squared Euclidean distance method is used to estimate the rotor position based on the table. The simulated and experimental results are presented demonstrating the feasibility and accuracy of this method.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.175-177
• /
• 1996

This paper is studied on the numerical analysis of temperature distribution on the Nb-foil due to the eddy current under operating a superconducting power supply. The increase of rotating speed and magnetic flux above critical magnetic field lead to the temperature rising in the normal spot, the heat was distributed in the region of 30% distance from the center of the normal spot, but the most of the heat was transferred to LHe. Under operation of the sc power supply, the increase of rotation speed has the more influence on the temperature rising than that of magnetic flux. we can conclude that the totaling speed of normal spot is the main design consideration of the sc power supply, and get the optimal value of rotating speed.

• International Journal of Fluid Machinery and Systems
• /
• v.8 no.3
• /
• pp.169-182
• /
• 2015

When simulating the dynamic behaviour of a hydro power plant, it is essential to have a good representation of the turbine behaviour. The pressure transients in the system occurs because the flow changes, which the turbine defines. The flow through the turbine is a function of the pressure, the speed of rotation and the wicket gate opening and is, most often described in a performance diagram or Hill diagram. In the Hill diagram, the efficiency is drawn like contour lines, hence the name. A turbines Hill diagram is obtained by performance tests on scaled model in a laboratory. However, system dynamic simulations have to be performed in the early stage of a project, before the turbine manufacturer has been chosen and the Hill diagram is known. Therefore one have to rely on diagrams for a turbine with similar speed number. The Hill diagram is drawn through measured points, so for using the diagram in a simulation program, one have to iterate in the diagram based on curve fitting of the measured points. This paper describes an alternative method. By means of the Euler turbine equation, it is possible to set up two differential equations which represents the turbine performance with good enough accuracy for the dynamic simulations. The only input is the turbine's main geometry, the runner blade in- and outlet angle and the guide vane angle at best efficiency point of operation (BEP). In the paper, simulated turbine characteristics for a high head Francis turbine, and for a reversible pump turbine are compared with laboratory measured characteristics.