• 대한기계학회논문집
• /
• 제17권11호
• /
• pp.2723-2729
• /
• 1993

Moire principles are applied to the measurement of the spindle radial error motion. As opposed to conventional techniques, no master cylinder or ball is needed in the measurement so that the offset and out-of-roundness errors of the master can be inherently eliminated. Two periodic circular gratings are used, one is made on the spindle and the other is held stationary on the reference frame. When the two gratings are seen superimposed during spindle rotation, an interference fringe pattern is observed from which the information on the eccentricity between the two gratings can be extracted with high precision. The optical design and fringe analysis techniques of a prototype measurement system are described in detail with exemplary measurement results.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2012년도 전기공동학술대회 논문집
• /
• pp.154-154
• /
• 2012

Many suggestions is offered to resolve global warming. Tidal current generation is producing power by switched tidal difference sea water horizontal fluid flow produced by tidal difference using rotor and generator. So, change the angle of inflow condition due to the entrance of efficiency are considered. We therefore investigated three dimensional flow analysis and performance evaluation using commercial ANSYS-CFX code for horizontal axis turbine. Then We also studied three dimensional flow characteristics of a rotating rotor and blade surface streamlines around a rotor. As a result, Cp was highest at TSR 5.5, especially the larger changes in the angle of inflow condition decreased efficiency.

• 한국전기전자재료학회논문지
• /
• 제13권9호
• /
• pp.801-804
• /
• 2000

High-temperature superconductor of Bi-2212 system was fabricated by CFP(Centrifugal Forming Process). To make a uniform specimen slurry was prepared in the ratio of 7:3(powder : binder) and ball milled for 24 hours. Milled slurry was charged into a rotating mold with 450 rpm and dried at room temperature. Then the specimen was performed binder burn-out at 35$0^{\circ}C$ and heated for partial melting to 86$0^{\circ}C$. XRD analysis of most specimens were shown 2212 phase and observed a local plate shped microstructure with a well aligned c-axis direction from SEM images. Measured T$_{c}$(Critical temperature) was about 64 K.K.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.590-593
• /
• 2009

Tidal current power system is one of ocean renewable energies that can minimize the environmental impact with many advantages compared to other energy sources. Not like others, the produced energy can be precisely predicted without weather conditions and also the operation rate is very high. To convert the current into power, the first device encountered to the incoming flow is the rotor that can transform into rotational energy. The performance of rotor can be determined by various design parameters including numbers of blade, sectional shape, diameter, and etc. The stream lines near the rotating rotor is very complex and the interference effects around the system is also difficult to predict. This paper introduces the experiment of rotor performance and also the effect of design parameter on the performance of HAT rotor by CFD.

• 대한방사선기술학회지:방사선기술과학
• /
• 제20권1호
• /
• pp.15-20
• /
• 1997

Unlike conventional CT scan, the helical CT scan uses continuous rotating CT equipment with a slip ring to move the patient's coach at a constant speed while continuously scanning. Slice sensitivity profiles in the Z-position(SSPz) using the conventional X-ray CT have a shape similiar to a rectangular wave, which slightly spreads out into plains below the mountain. However, in the helical CT, with an expansion of the base, the rectangular shape collapses and a mouatain-like shape can be seen. We need to investigate the fellowing factors in helical CT scanning;the ability to scan along the axis of the body, effective slice width, slice shape and the precision of coach velocity, Helical scanning with sprial X-ray track is different from the conventional scanning in terms of the principle of image reconstruction performed. We believe that the problems in helical scanning can be solved by understanding new the special parameters such as the bed moving speed and the interval of image reconstruction.

• International Journal of Aeronautical and Space Sciences
• /
• 제9권2호
• /
• pp.58-63
• /
• 2008

This paper describes aerodynamic performance enhancement of cycloidal rotor according to the blade pivot point movement and the blade preset angle adjustment. Cycloidal blade system which consists of several blades rotating about an axis in parallel direction and changing its pitch angle periodically, is a propulsion mechanism of a new concept vertical take off and landing aircraft, cyclocopter. Based on the designed geometry of cyclocopter, numerical analysis was carried out by a general purpose commercial CFD program, STAR-CD. According to tills analysis, the efficiency of cycloidal rotor could be improved more than 15% by the introduced methods.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2005년도 동계학술발표대회 논문집
• /
• pp.335-340
• /
• 2005

Nonlinear and forced oscillations of supported viscous droplet were focused in the present study. The droplet has a free contact line with solid plate and inviscid fluid. Natural frequencies of a pendant droplet have been investigated experimentally by imposing the acoustic wave while the frequency is being increased at a fixed amplitude. The evaporation was observed at atmosphere pressure. The droplet was recorded throughout the entire evaporation process and transient variations of the volume was measured. The evaporation process of oscillating droplet with thermofoil has been also observed to investigate analyzing the resonance effect on the thermal characteristics of droplet. It is found that a pendant droplet shows the resonant behaviors at each mode similar to the theoretical analysis. During imposing the acoustic wave, the pendant droplet makes a rotating motion in its longitudinal axis which is a new shape oscillation mode. The evaporation rate of a pendant droplet at resonant frequency is significantly enhanced.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.207-209
• /
• 2005

Recently, the use of IPMSM is coming to be active, in many industrial applications. In sensorless drive of IPMSM, it is important to know the exact information of the initial rotor position, because the wrong estimation of the initial rotor position brings about the decrease of the starting torque, or a temporary reverse revolution, In addition, PMSM is necessary to use the accurate information of the inductance for the precise torque control owing to the reluctance torque. In this paper presents initial rotor position estimation method and, measure method of the each-axis inductance. And to minimize the speed estimations error, the estimated speeds are compensated by using an instantaneous reactive power in synchronously rotating reference frame.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2003년도 가을 학술발표회 논문집
• /
• pp.47-54
• /
• 2003

The rotating of rotatory unit with its structural unbalance mass and laundry is making the main vibration problem in a vertical axis washing machine. For reducing vibration problem total washing system hung on the case by its suspension system which is constitute of spring, damper and suspension bar and hydraulic balancer is attached at the upper rim of spin basket. In this paper, we make the dynamic model of washing system of its rigid body motions by 6 degree of freedoms. Hydraulic balancer is modeled by one degree of freedom like auto ball balancer. Elastic motions of washing system have found by method of analytic, experimental and FEM. And we consider first bending mode of each suspension bar and first circumferential mode of assy tub. So, the total washing system is modeled by 12 degree of freedoms. Equations of motion for total washing system have derived, and we perform the dynamic simulation tests.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.416-421
• /
• 2001

It was firstly issued that frequently broken of Encoder installed at travelling motor during RTGC operation. Estimated as broken due to excessive vibration of traveling and motor manufacturer claimed it as resonance of motor base. The principal vibration of Encoder was caused by the rotating vibration component of motor and by traveling wheel. The component transmitted from the wheel didn't have great vibration by the resonance with motor and other parts. Therefore, the plans was tried to add the support point to prevent the Encoder shaft vibrated greatly and inhibit the vibration. These showed good results.