• International Journal of Fluid Machinery and Systems
• /
• v.3 no.3
• /
• pp.211-220
• /
• 2010

The objective of this study is to clarify the occurrence of the high-speed mode of unsteady swirling flows in straight tubes. The unsteady flows generated in the tube were measured by means of a semiconductor-type pressure transducer and an FFT analyzer. The high-speed mode measured has rotational speed which is approximately equal to or higher than the peripheral velocity of the swirling flow. The unsteady flow is due to cell rotation in the circumferential direction of the tube. The occurrence of the high-speed mode was confirmed, and the characteristics (rotational speed, pressure amplitude, and phase) of this mode were clarified. In order to understand the measured unsteady flows, the three dimensional vortex core profiles were discussed based on the distributions of the pressure amplitude and phase.

• The KSFM Journal of Fluid Machinery
• /
• v.2 no.2 s.3
• /
• pp.57-63
• /
• 1999

The flow through multistage turbomachinery is affected by the interaction between a rotor and a stator. The interaction is due to the inviscid potential effect and viscous effect between closely spaced rotor and stator airfoils. Three-dimensional, unsteady, incompressible Navier-Stokes equations with a standard $k-{\epsilon}$ model are solved using a non-staggered grid system. This method is applied to the flow through a multistage compressor measured by Stauter et al. The results have shown strong interaction between the rotating and stationary flow field. The decay of rotor wake and the pressure profiles agree very well with experimental data. The wake produced by rotor causes unsteady pressure on the surface of a stator. The rotor/stator interaction produces the unsteady pressure force on the rotor and stator blades.

• The KSFM Journal of Fluid Machinery
• /
• v.2 no.2 s.3
• /
• pp.27-31
• /
• 1999

This paper describes the shaft vibration phenomena measured on a pump-turbine of a pumped storage power plant. The pump-turbine runs at a rotational speed of 450 rpm (7.5 Hz). The power output (load) of the pump-turbine is varied from 100 to 300 MW in the generating mode. The magnitude of the shaft vibration highly depends on the power load. The vibration magnitude of the shaft is very high in the middle load zone from 170 to 210 MW, elsewhere the vibration is low. From nitration spectra, it is shown that the frequency of major nitration in that load zone is 2.5 Hz which is approximately $34\%$ of the shaft rotating speed in Hz. This frequency component does not occur below and above that load zone. This subsynchronous vibration is caused by the flow induced disturbance due to spiral vortex flow downstream of the pump-turbine runner. Furthermore, the shaft vibration is highly decreased due to an increased bearing preload.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.822-825
• /
• 2002

A lot of rotating machinery are generally used in industrial field and the electrical machinery such as the motor and generator account for the most of the part. Generally motor and generator have electrical loss because of eddy current. So silicon steel sheets are used in order to reduce the electrical loss and furthermore laminated rotor is used for motor and generator to eliminate the electrical loss and heat generation. However, the more high speed, large scale and high precision of the system, the more important to estimate the critical speed. In this paper verifies the variation of the critical speeds in accordance with the variation of the pressing force of lamination plate for the rotor which is supported by ball bearing with the experimental data as well.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.676-685
• /
• 1993

A mathematical model was developed to quantify the separation process of threshed grain-straw mixtures. It was made to predict the separation loss from a separation unit consisted of stationary crimped sieve with rotating inner rotor. Experiments were performed to prove the mathematical model by changing various levels of pertinent variables for rice. Good Agreement between the simulated results and observed data under the various test conditions, such as inclination angle of the separator, vane pitch, rotor speed, MOG/G ratio, feed rate, and crop variety and moisture content, were confirmed.

• The KSFM Journal of Fluid Machinery
• /
• v.4 no.3 s.12
• /
• pp.21-28
• /
• 2001

The effects of diffuser shapes on the flowfields of a small-size turbo-compressor have been investigated numerically and experimentally. The optimal design of elements shapes is important to develop the high efficiency turbo-compressor. Typical range of rotating speed for a small-size turbo-compressor is 40,000-70,000rpm. Numerical analyses were conducted to the rectangular and conical shapes of diffuser Three-dimensional, steady and viscous governing equations were solved by SIMPLE algorithm. To confirm the numerical results, the experimental measurements for the static pressure and temperature at the inlet and outlet boundaries were performed. Comparisons of these results were done, and the reasonable agreements were acquired.

• The KSFM Journal of Fluid Machinery
• /
• v.6 no.2 s.19
• /
• pp.15-22
• /
• 2003

Comprehensive study on a centrifugal blower for air-purifier involving a few physical filters for percolation process has been accomplished for an optimal design of the air handling system. The filtering media causes a flow resistance for induced flows by a rotating impeller. The present methodology is to adopt PIV system for velocity measurements and wind tunnel connected with an anechoic chamber for total performance test of the blower. Trial prototypes for the blades of a rotor and casing are presented for satisfaction of both flow rate and noise level set by design objectives. Tapered blades with a special casing for a fan show good performance data. The results of velocity fields also explain the reason of improvements of the blower performance.

• The KSFM Journal of Fluid Machinery
• /
• v.6 no.2 s.19
• /
• pp.62-69
• /
• 2003

An oil-free turbo-compressor supported by compliant foil bearings which remove oil-contamination by elimination of a conventional ball bearing and oil lubrication systems is presented. Turbo-compressor makes two individual air compressions with two impellers at a operating speed of 39,000 rpm. In this study, the rotordynamic effects caused by aerodynamic instability were investigated with variable mass flow rates. Correlations between frequencies of pressure fluctuation in two diffusers and those of excitation forces on rotor were clearly observed in an aerodynamic unsteady region. Thus, these results show that it is beneficial to design high-speed rotating turbomachinery by considering coupling effect between aerodynamic instability and rotordynamic force.

• International Journal of Fluid Machinery and Systems
• /
• v.2 no.3
• /
• pp.206-214
• /
• 2009

Alternate blade cavitation, rotating cavitation and cavitation surge in rocket turbopump inducers were simulated by a three dimensional commercial CFD code. In order to clarify the cause of cavitation instabilities, the velocity disturbance caused by cavitation was obtained by subtracting the velocity vector under non-cavitating condition from that under cavitating condition. It was found that there exists a disturbance flow towards the trailing edge of the tip cavity. This flow has an axial flow component towards downstream which reduces the incidence angle to the next blade. It was found that all of the cavitation instabilities start to occur when this flow starts to interact with the leading edge of the next blade. The existence of the disturbance flow was validated by experiments.

• The KSFM Journal of Fluid Machinery
• /
• v.11 no.4
• /
• pp.22-31
• /
• 2008

In this study, computer applied engineering (CAE) techniques are fully used to conduct structural and dynamic analyses of a huge composite rotor blade. Computational fluid dynamics is used to predict aerodynamic load of the rotating wind-turbine blade model. Static and dynamic structural analyses are conducted based on finite element method for composite laminates and multi-body dynamic simulation tools. Various numerical results for aerodynamic load, static stress, buckling and dynamic analyses are presented and characteristics of structural behaviors are investigated herein.