• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.532-535
• /
• 2003

Vibration of rotating machinery is a factor that is something to do with abnormal machinery. Former days, Perception of vibration at rotating machinery had used Shaft rider type. Shaft rider type was adhered to surface of shaft and detected vibration of rotating machinery. Recently, Perception of vibration at rotating machinery uses to non-contact sensor. Working principle of non-contact sensor is used of eddy current. Vibration at rotating machinery appears to deviation of eddy current. In this paper, We investigate abnormal vibration due to non-contact sensor.

• Smart Structures and Systems
• /
• v.6 no.4
• /
• pp.389-403
• /
• 2010

By using image recognition technology, this paper presents a new fault diagnosis method for rotating machinery with artificial immune algorithm. This method focuses on the vibration state parameter image. The main contribution of this paper is as follows: firstly, 3-D spectrum is created with raw vibrating signals. Secondly, feature information in the state parameter image of rotating machinery is extracted by using Wavelet Packet transformation. Finally, artificial immune algorithm is adopted to diagnose rotating machinery fault. On the modeling of 600MW turbine experimental bench, rotor's normal rate, fault of unbalance, misalignment and bearing pedestal looseness are being examined. It's demonstrated from the diagnosis example of rotating machinery that the proposed method can improve the accuracy rate and diagnosis system robust quality effectively.

• Journal of KSNVE
• /
• v.10 no.2
• /
• pp.331-337
• /
• 2000

The necessity of diagnosis of the rotating machinery which is widely used in the industry is increasing. Many research has been conducted to manipulate field vibration signal data for diagnosing the fault of designated machinery. As the pattern recognition tool of that signal, neural network which use usually back-propagation algorithm was used in the diagnosis of rotating machinery. In this paper, self-organizing feature map(SOFM) which is unsupervised learning algorithm is used in the abnormal defect diagnosis of rotating machinery and then learning vector quantization(LVQ) which is supervised learning algorithm is used to improve the quality of the classifier decision regions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.6
• /
• pp.262-273
• /
• 1995

For rotating machinery with high speed and high efficiency, large labor and high expenses are required to conduct machine health monitoring. Therefore, it becomes necessary to develop new diagnosis technique which can detect abnormalities of the rotating machinery effectively. In this paper, it is identified that bispectrum analysis technique can be successfully applied to dectect the abnormalities of the roating machinery through computer simulation, and results of the bispectrum analysis are patterned in griding form. Further, pattern recognition technique using back propagation algorithm, which is one of neural network algorithm, being consisted of patterned input layer and output layer for abnormal status, is applied to detect the abnormalities of simulator which is able to make up various kinds of abnorml conditions(misalignment, unbalance, rubbing etc.) of the rotating machinery.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.539-543
• /
• 2001

Almost all rotating machinery has bearings. Bearing is one of the most important part of rotating machinery. Vibration of rotating machinery depend on its bearing conditions. Bearing conditions are followings ; oil gap, bearing type, bearing temperature, bearing oil condition. Especially, bearing oil condition influences on rotating machinery vibration directly. In this paper we have discussed the abnormal vibration of turbine due to oil condition. oil whip problem was occured in the certain power plant. and we had sloved this problem through the control of operating values and alignment.

• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.224-226
• /
• 2001

In this paper, a novel high-voltage motor monitoring system (HVMMS) is proposed. This system monitors the insulation condition of the stator winding by on-line measurements of partial discharge (PD). Sensor, EMC (Epoxy-Mica Coupler) is used for PD measurement PD signals are continuously measured and digitized with a peak-hold A/D converter to build the database of the high-voltage motor's insulation condition. Also, this system can communicate with the central monitoring system via RS-485. This helps more efficient operation and maintenance of the generator.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.895-902
• /
• 2007

Rotating machinery has two typical faults with clearance, one is partial rub and the other is looseness. Due to these faults, non-linear and non-stationary signals are occurred. Therefore, time-frequency analysis is necessary for exact fault diagnosis of rotating machinery. In this paper newly developed time-frequency analysis method, HHT(Hilbert-Huang Transform) is applied to fault diagnosis and compared with other method of FFT, SFFT and CWT. The results show that HHT can represent better resolution than any other method. Consequently, the faults of rotating machinery are diagnosed efficiently by using HHT.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1046-1050
• /
• 2000

The necessity of diagnosis of the rotating machinery which is widely used in the industry is increasing. If rotating machinery has fault, we can detect fault using vibration or noise. But, in diagnosing rotating machinery, the end user who doesn't have expert knowledge needs the help of vibration diagnosis expert. However, vibration diagnosis experts who well satisfy the demand of end user are rare. So, this paper propose a development of the case-based reasoning system for abnormal vibration diagnosis of rotating machinery we construct the past experiences of vibration diagnosis expert into case base and shear the experiences of diagnosis expert with the end user. In this paper, we describe that process of structured system and adapting result of abnormal vibration diagnosis of electric motor.

• 유체기계공업학회:학술대회논문집
• /
• 1999.12a
• /
• pp.317-323
• /
• 1999

The necessity of diagnosis of the rotating machinery which is widely used in the industry is increasing. Many research has been conducted to manipulate field vibration signal data for diagnosing the fault of designated machinery. As the pattern recognition tool of that signal, neural network which use usually back-propagation algorithm was used in the diagnosis of rotating machinery. In this paper, self-organizing feature map(SOFM) which is unsupervised learning algorithm is used in the abnormal vibration diagnosis of rotating machinery and then learning vector quantization(LVQ) which is supervised teaming algorithm is used to improve the quality of the classifier decision regions.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1126-1131
• /
• 2001

Excessive vibration in rotating machinery is a problem encountered in many different fields, causing such difficulties as fatigue of machinery components and failure of supporting bearings. Passive techniques, though sometimes limited in their capabilities, have been used in the past to attenuated vibrations. Recently active techniques have been developed to provide vibration control perform beyond that provided by their passive counters. Most often, the focus of active control methods has been to suppress rotating machinery displacements. In cases where vibration results in bearing failures, displacement suppression may not be the best choice of control approaches (it can, in fact, increase dynamic bearing loads which would be even more harmful to bearings). This paper presents two optimal control methods for attenuating steady state vibrations in rotating machinery. One method minimizes shaft displacements while the other minimizes dynamic bearing reaction forces. The two methods are applied to a model of a typical rotating machinery system and their results are compared. It is found that displacement minimization can increase bearing loads, while bearing load minimization, on the other hand, decreases bearing loads.