• Journal of Welding and Joining
• /
• 제19권3호
• /
• pp.298-304
• /
• 2001

Turbine blade is subject to force of three types ; the torsional force by torsional mount, the centrifugal force by the rotation of rotor and the cyclic bending force by steam pressure. The cyclic bending force was a main factor on fatigue strength. SEM fractography in root of turbine blade showed micro-clack width was not dependent on stress intensity factor range. Especially, fatigue did not exist on SEM photograph in root of turbine blade. To clear out the fracture mechanism of turbine blade, nanofractography was needed on 3-dimensional crack initiation and crack growth with high magnification. Fatigue striation partially existed on AFM photograph in root of turbine blade. Therefore, to find a fracture mechanism of the torsion-mounted blade in nuclear power plant, the relation between stress intensity factor range and surface roughness measured by AFM was estimated, and then the load amplitude ΔP applied to turbine blade was predicted exactly by root mean square roughness.

• 한국음향학회지
• /
• 제42권6호
• /
• pp.491-499
• /
• 2023

해수면 거칠기에 의해 해수면 산란이 발생하면 통신신호의 주파수 확산과 통신채널 시변동성을 야기하여 통신성능을 악화시킨다. 수면 거칠기에 따른 통신채널의 시변동성 차이를 비교하기 위하여 한양대학교 해양음향공학연구실 수조에서 실험을 수행하였다. 수조에서 인위적인 수면 거칠기를 생성하고 대역폭에 따른 차이를 비교하기 위하여 3가지 대역폭을 갖는 통신신호를 사용하였다. 측정된 수면 거칠기는 레일리 파라미터로 변환하여 거칠기에 대한 파라미터로써 사용하였으며, 수면 경로의 시변 채널 특성은 도플러 확산과 상관시간을 이용하여 통계적 분석을 수행하였다. 수면 경로의 도플러 확산은 통신신호의 반송 주파수와 대역폭의 영향을 보정한 가중 유효 도플러 확산(Weighted Root Mean Square Doppler spread, w_fσ_ν)을 사용하였다. 수면 경로의 상관시간과 직접 경로와 수면 경로의 에너지 비율을 이용하여 전체 채널의 상관관계를 모의하고 측정된 전체 채널의 상관시간과 비교하였다. 본 연구에서는 해수면 거칠기에 따른 해수면 경로의 시변 채널특성을 이용하여 임의의 해양환경에서 효율적인 통신신호 설계를 위한 방법을 제안한다.

• 한국자동차공학회논문집
• /
• 제9권6호
• /
• pp.170-177
• /
• 2001

Turbine blade is subject to torsional load by torsion-mount, centrifugal load by rotation of rotor and repeated bending load by steam pressure. Turbine with partially cracked blade has normal working condition at initial repair time but vibratory working condition at middle repair time due to crack growth. Finite element analysis on turbine blade indicates that repeated bending load out of all loads is the most important factor on fatigue strength of turbine blade. Therefore, this study shows root mean square roughness has linear relation with stress intensity factor range in 12% Cr steel and can predict loading condition of fractured turbine blade.

• 대한설비공학회지:설비저널
• /
• 제13권4호
• /
• pp.209-214
• /
• 1984

Friction factors and equivalent sand roughness of PVC pipe fittings have been studied by experiments in the Reynolds number range of $2,000\~70,000$. PVC pipe fittings studied are straight pipes, $90^{\circ}$ elbows and tees with 15, 25, and 40mm in norminal diameter, all manufactured in Korea with KS mark approval. Equivalent relative roughness of PVC pipes obtained lies between smooth pipe and 0.002. The study shows that equivalent sand roughness of PVC pipes increasses in proportion of the square root of pipe diameter , and can be approximately abtained by multiplying 4 to the root mean square value measured by metal surface roughness tester. Loss coefficient of PVC $90^{\circ}$ elbows decreases slowly with increasing Reynolds number. Loss coeffiicent of tees is a function of ratio of flow rates and Reynolds number.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.585-590
• /
• 2001

Turbine blade is subject to torsional load by torsion-mount, centrifugal load by rotation of rotor and repeated bending load by steam pressure. Turbine with partially cracked blade has normal working condition at initial repair time but vibratory working condition at middle repair time due to crack growth. Finite element analysis on turbine blade indicates that repeated bending load out of all loads is the most important factor on fatigue strength of turbine blade. Therefore, this study shows root mean square roughness has linear relation with stress intensity factor range in 12% Cr steel and can predict loading condition of fractured turbine blade.

• Restorative Dentistry and Endodontics
• /
• 제43권1호
• /
• pp.10.1-10.8
• /
• 2018

Objectives: To examine the surface topography of intact WaveOne (WO; Dentsply Sirona Endodontics) and WaveOne Gold (WOG; Dentsply Sirona Endodontics) nickel-titanium rotary files and to evaluate the presence of alterations to the surface topography after root canal preparations of severely curved root canals in molar teeth. Materials and Methods: Forty-eight severely curved canals of extracted molar teeth were divided into 2 groups (n = 24/each group). In group 1, the canals were prepared using WO and in group 2, the canals were prepared using WOG files. After the preparation of 3 root canals, instruments were subjected to atomic force microscopy analysis. Average roughness and root mean square values were chosen to investigate the surface features of endodontic files. The data was analyzed using one-way analysis of variance and post hoc Tamhane's tests at 5% significant level. Results: The surface roughness values of WO and WOG files significantly changed after use in root canals (p < 0.05). The used WOG files exhibited higher surface roughness change when compared with the used WO files (p < 0.05). Conclusions: Using WO and WOG Primary files in 3 root canals affected the surface topography of the files. After being used in root canals, the WOG files showed a higher level of surface porosity value than the WO files.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.392-392
• /
• 2010

In this study, high-speed chemical dry thinning process of Si wafer and evolution of surface roughness were investigated. Direct injection of NO gas into the reactor during the supply of F radicals from $NF_3$ remote plasmas was very effective in increasing the Si thinning rate due to the NO-induced enhancement of surface reaction but thinned Si surface became roughened significantly. Addition of Ar gas, together with NO gas, decreased root mean square (RMS) surface roughness of thinned Si wafer significantly. The process regime for the thinning rate enhancement with reduced surface roughness was extended at higher Ar gas flow rate. Si wafer thinning rate as high as $22.8\;{\mu}m/min$ and root-mean-squared (RMS) surface roughness as small as 0.75 nm could be obtained. It is expected that high-speed chemical dry thinning process has possibility of application to ultra-thin Si wafer thinning with no mechanical damage.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.124-128
• /
• 2004

A Poly-Si and a ITO films with surface roughness 1.8 nm and 0.5 nm of root mean square ($R_{rms}$ vakue) values were developed, respectively. A 3 inch UXGA LTPS TFT-LCD with 667 ppi resolution and a 10 inch VGA LTPS OLED have been developed and demonstrated using PMOS technology.

• 지질공학
• /
• 제32권1호
• /
• pp.85-99
• /
• 2022

Rock discontinuities, as weak interfaces in rock, control mechanical properties of rock mass. Presence of discontinuities complicates the engineering properties of rock, which is the root of anisotropy and heterogeneity that have nonnegligible influences on the rock engineering. Morphological characteristics of discontinuities in natural rock are an important factor influencing the mechanical properties, particularly roughness, of discontinuities. Therefore, the accurate measurement and characterization of morphologies of discontinuities are preconditions for studying mechanical properties of discontinuities. Taking discontinuities in red sandstone as research objects, the research obtained three-dimensional (3D) morphologies of discontinuities in natural rock by carrying out 3D morphological scanning tests. The waviness and roughness were separated from 3D morphologies of rock discontinuities through wavelet transform. In addition, the calculation method for the overall slope root mean square (RMS) as well as slope RMSs of waviness and roughness of 3D morphologies of discontinuities considering the shear direction was proposed. The research finally determined an evaluation method for 3D morphologies of discontinuities by quantitatively characterizing 3D morphologies with the mean value of the three slope RMSs.

• 대한기계학회논문집A
• /
• 제25권11호
• /
• pp.1705-1712
• /
• 2001

Mechanical component has striation with constant width and SEM can estimate fracture type and loading condition. SEM has benefit to fatigue fracture analysis but striation can be observed according to the kind of material and range of crack growth rate and can't. In this case, it needs AFM that can measure 3-dimensional surface profile with resolution of atomic size. In this study. to find fracture reason of torsion-mounted blade in nuclear plant, we estimate the relation between stress intensity factor range and root mean square roughness in 12% Cr steel by AFM and predict in-service loading condition of turbine blade. failure analysis is performed by finite element method and Goodman diagram on torsion-mounted blade.