• 한국전기전자재료학회논문지
• /
• 제33권6호
• /
• pp.465-470
• /
• 2020

Heterolayered K(Ta,Nb)O₃/Pb(Zr,Ti)O₃ thin films on Pt/Ti/SiO₂/Si substrates were prepared by a sol-gel process and spin-coating method. The structural and electrical properties were measured to investigate the possibility of application as an electrocaloric effect device. All specimens exhibited dense and uniform cross-sectional structures without pores, and the average thickness of the specimen coated six times was approximately 394 nm. Curie temperatures were observed at 5℃ or less in type-I and 10℃ in type-II specimens, respectively. Type-II specimens coated 6 times showed a relative dielectric constant of 758 and remanent polarization of 9.71 μC/㎠ at room temperature. The maximum electrocaloric effect occurred between 20 and 25℃, slightly higher than their Curie temperature, and the electrocaloric property (ΔT) of the type-II specimens coated 6 times was approximately 1.2℃ at room temperature.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.193-193
• /
• 2011

To obtain ceramic films, the sol-gel coating technique has been broadly used with heat treatment, but crack formation tend to occur during heat treatment in thick sol-gel films. We prepared PZT thin films by sol-gel method with single-step spin coating process. The PZT solution have been synthesized using lead acetate ($Pb(CH_3COO)_2$), zirconium acetylacetonate ($Zr(OC_3H_7^n)_4$), and titanium diisopropoxide bis(acetylacetonate) 75wt% in isopropanol ($Ti(OC_3H_7^i)_2(OC_3H_7^n)_2$) as starting materials and n-propanol was selected as a solvent. The poly(vynilpyrrolidone) (PVP) was added with 0, 0.25, 0.5, 0.75, and 1 molar ratios to control viscosity of solution. We investigated influence of the viscosity on thickness, microstructure, and electrical properties of final PZT films. Thermo-gravimetric analysis and differential scanning calorimeter (TGA/DSC) was carried out from room temperature to $800^{\circ}C$ in order to measure pyrolysis temperature. Structural characteristics were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Ferroelectric and dielectric properties were measured by RT66A (Radiant) and impedance analyzer (Agilent), respectively. The thicknesses of PZT films depended on incorporation of an excess amount of PVP. Finally, we obtained PZT films of good quality without crack formation via single-step spin coating.

• Korean Chemical Engineering Research
• /
• 제45권5호
• /
• pp.442-447
• /
• 2007

투명 플라스틱 필름의 표면강도를 향상시키기 위하여 유-무기 혼성 코팅용액을 Sol-Gel 법을 이용하여 합성하였다. 코팅용액은 입자 직경이 12 nm 크기의 무기물인 colloidal silica 용액(Ludox)에 유기물인 GPTMS(glycidoxypropyl trimethoxysilane)를 첨가하여 제조하였다. 그 후에 기재인 PC(polycarbonate) 필름에 담금 코팅(dip-coating)시키고, 상온에서 10분 동안 건조시킨 후, $80^{\circ}C$에서 30분 동안 열 경화시켜 하드 코팅 막을 제조하였다. 이 과정 중 코팅용액의 pH 변화와 GPTMS 첨가량의 변화가 코팅 막의 물성에 미치는 영향을 살펴보았다. pH 4의 산성 조건에서 제조된 코팅용액으로 PC 필름 위에 코팅한 경우는 중성이나 염기성 조건으로 제조된 경우 보다 우수한 연필경도 및 기재와의 부착력을 보였다. 또한 GPTMS의 첨가량이 증가할수록 코팅 막의 연필경도 및 기재와의 부착력이 증가하였다.

• 한국식품저장유통학회지
• /
• 제5권2호
• /
• pp.138-143
• /
• 1998

The stowage effects of Satsuma mandarin(Citrus unshiu Marc. var. miyagawa) were investigated by selecting various pretreatmnents; non-tested, wax-coating, paper packaging, 0.02mm cryovac film packaging. Weight loss of film packaging was the lowest among that of others, but decay radio was increased highly at late stages of storage. Soluble solids, moisture content of peel and total sugar were maintained almost constant, but acid content, vitamin C and firmness were reduced gradually during storage at room temperature. For 100 days storage, losses from weight and decay of ton-treated, paper packaging, wax-coating and film packaging were 15.9%, 18.5%, 17.4% and 12.9%, respectively. Acid content was decreased loom 1.28% to 0.81∼0.91% after 100 days storage. Ethylene evolution was increased in a degree after 65 days storage, and the amount was increased repidly afer 115 days. it seemed to be derived from decayed fruits and physiological activities. CO2 content of inner part of fruits was increased between 40∼100 days after storage. Optimum storage period of early variety of Satuma mandarin was regarded for 100days on the basis of appeareance and taste.

• 한국세라믹학회지
• /
• 제33권12호
• /
• pp.1301-1310
• /
• 1996

Generally it requires high sintering temperatures more than 135$0^{\circ}C$ to make semiconductive BaTiO3 ceramics. Also it is very difficult to achieve a homogeneous mixing in solid-state reaction method. Therefore the liquid phase distributed to non-uniform dilute the characteristics of PTCR. In order to improve the uniformity this study is used the sol-gel coating method. Using this method we studied the new manufacturing process that had a high reproducibility and mass production capability. Tetraethyl orthosilicate (TEOS) was used as a source of Si. The semiconductive BaTiO3 ceramics which was produced by sol-gel method for the SiO2 addition and sintered between 124$0^{\circ}C$ and 130$0^{\circ}C$ showed almost same resistivity at room temperature among 125$0^{\circ}C$ and 130$0^{\circ}C$. As the results We could be sintered the semiconducting BaTiO3 ceramics at lower temperature even at 125$0^{\circ}C$ maintaining the same specific resistivity ratio ($\rho$max/$\rho$min) at 130$0^{\circ}C$. The specific resistivity both below and above the Curie temperature were increased by slow cooling and the steepness of the plots in the reasion of transition from low to high resistance increased as the cooling rate decreased.

• 대한전기학회논문지
• /
• 제44권7호
• /
• pp.914-918
• /
• 1995

In this study, Pb(Zr$_{x}$ Ti$_{1-x}$ )O$_{3}$ (x=0.65, 0.52, 0.35) thin films were fabricated by Sol-Gel method. A stock solution with excess Pb 10[mol%] of Pb(Zr$_{x}$ Ti$_{1-x}$ )O$_{3}$ was made and spin-coated on the Pt/SiO$_{2}$/Si substrate at 4000[rpm] for 30[sec.]. Coated specimens were dried on the hot-plate at 400[.deg. C] for 10[min.]. Sintering temperature and time were 500~800[.deg. C] and 1~60[min.]. The coating process was repeated 6 times and the final thickness of the thin films were about 4800[A]. To investigate crystallization condition, PZT thin films were analyzed with sintering temperature, time and composition by the XRD. The microstructure of thin fulms were investigated by SEM. The ferroelectric perovskite phases precipitated under the sintering of 700[.deg. C] for 1 hours. In the PZT(52/48) composition, dielectric constant and dielectric loss were 2133, 2.2[%] at room temperature, respectively.ively.

• Journal of Magnetics
• /
• 제21권4호
• /
• pp.622-628
• /
• 2016

Magnetization property is a critical factor for magnetorheological fluids (MRFs) to achieve the liquid-solid transition. The main focus of this study is on exploring the influence factors on magnetization properties of MRFs. In this paper, a theoretical analysis is performed to discuss the magnetization characteristics of MRFs firstly. Then, a method for the preparation of carbonyl iron-based MRFs is illustrated and five MRFs samples with various material parameters are prepared. It is succeeded by a series of experiments on testing the hysteresis loop and the magnetization curve of each sample and the influence factors are compared and analyzed. Experimental results indicate that there is basically no hysteresis phenomenon on MRFs which exhibits superparamagnetic behavior at room temperature. A surfactant coating on magnetic particles can slightly improve the MRFs magnetization. Additionally, the magnetic susceptibility and the saturation magnetization both increase with the particle concentration, whereas the influence of particle diameter is relatively very small. Moreover, as the temperature increases, the magnetization decreases and the declining rate accelerates gradually.

• Tribology and Lubricants
• /
• 제19권5호
• /
• pp.274-279
• /
• 2003

$Al-SiC_{p}$ composite layer was prepared by plasma thermal spray on aluminum substrate. The homogeneously dispersed composite powder for thermal spray was fabricated by mechanical alloying with ball mill. The friction tests of the composite layers and commercial aluminum alloys for comparison were performed in the temperature range of 20∼$260^{\circ}C$ with the interval of $40^{\circ}C$ with steel counter-face. Friction coefficient was recorded during test sequence, and the microstructure of surface and debris was investigated by optical and scanning electron microscope. Friction coefficients of composite and aluminum alloys at room temperature were similar except pure aluminum. As the temperature increase, friction coefficient was increased rapidly in AC4C, AC2A. But friction coefficient of $Al-SiC_{p}$ composite was not increased so much up to $220^{\circ}C$. Consequently, the reinforcement of $SiC_{p}$ into aluminum matrix increased the stability of friction coefficient as well as wear resistance.

• 접착 및 계면
• /
• 제16권1호
• /
• pp.15-21
• /
• 2015

본 연구에서는 자동차 선도장 강판용 베이스코트 도료들의 유변물성 및 롤코팅 공정에서의 유동 특성을 고찰하였다. 베이스코트 3종 색상 도료들의 상온 조건에서 전단 점도와 열경화 조건에서 탄성/점성 모듈러스의 변화를 회전형 유변물성 측정기를 통해 분석하였다. 이를 통해 작용기의 배합비율과 열경화 이전의 전단 점도 특성이 경화에 의한 도료 내 가교구조 형성에 큰 영향을 주었음을 확인하였다. 또한, 3-롤코팅 공정에서 베이스코트 도료들의 코팅 특성 및 유동 불안성정을 관찰하여 코팅 운전 영역을 설정하였다. 이러한 유변학적 접근법은 비뉴튼성 도료의 친환경적 선도장강판 코팅 기술 개발 및 최적의 안정한 조건 설정을 위해 유용하게 활용될 수 있음을 보였다.

• 한국식품저장유통학회:학술대회논문집
• /
• 한국식품저장유통학회 2007년도 학술발표회
• /
• pp.161.1-161.1
• /
• 2007