• Journal of the Korea Society for Simulation
• /
• v.32 no.4
• /
• pp.77-84
• /
• 2023

In the agricultural sector, power sources are being developed that use alternative energy sources such as electric tractors and hydrogen tractors, away from internal combustion engine tractors. As parts such as engines and transmissions used in conventional internal combustion engine tractors are replaced with motors and batteries, the center of gravity changes, and thus the risk of rollover should be considered. The purpose of this study is to analyze the overturn angle of the main parts of the electric tractor through dynamic simulation to minimize the overturn accident and to derive the optimal arrangement of parts to improve stability. A total of nine dynamics simulations were conducted by designing three components of the PTO motor, drive motor and the battery pack, and three factors of the arrangement method. As a result of the experiment, it was confirmed that Type3 Level3, in which the drive motor and the PTO motor are located at the front and rear of the tractor, and two battery packs are located in the middle of the tractor, has a high rollover angle. As a result of this study, the stability increased as the center of gravity was placed backward and located below. Future research needs to be done to find the optimal location of parts considering their performance and placement efficiency.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.194.1-194.1
• /
• 2005

• Journal of Positioning, Navigation, and Timing
• /
• v.3 no.1
• /
• pp.1-10
• /
• 2014

Recently, monitoring of two-body ground vehicles carrying extremely hazardous materials has been considered as one of the most important national issues. This issue induces large cost in terms of national economy and social benefit. To monitor and counteract accidents promptly, an efficient methodology is required. For accident monitoring, GPS can be utilized in most cases. However, it is widely known that GPS cannot provide sufficient continuity in urban cannons and tunnels. To complement the weakness of GPS, this paper proposes an accident monitoring method based on a monocular vision sensor. The proposed method estimates angular acceleration from a sequence of image frames captured by a monocular vision sensor. The possibility of using angular acceleration is investigated to determine the occurrence of accidents such as jackknifing and rollover. By an experiment based on actual measurements, the feasibility of the proposed method is evaluated.

• International journal of advanced smart convergence
• /
• v.8 no.4
• /
• pp.161-168
• /
• 2019

Traffic accidents in tunnel can lead to large traffic accidents due to narrow and dark road characteristics. Therefore, special care of the driver is required when is driving in a tunnel. However, accidents can happen at any time. In the event of an accident, a narrow road structure may lead to a second accident. Therefore, all facilities installed inside the tunnel should be allowed to minimize damage in the event of an accident. We confirmed the safety of the collision target through the action of the sedan, Sport Utility Vehicle (SUV) and truck when the vehicle crashed into a stairway installed on the tunnel emergency escape route, and when a concrete barrier or guard rail was installed in front of the stairway. The behavior of the vehicle has resulted in a total of three results: rollover or rollover, change of speed and angle of the vehicle after collision. The sedan and SUV were the most secure when colliding with the guardrail, but considering the truck as a whole, concrete barriers were judged to be the most suitable for minimizing damage from the first accident and reducing the risk of the second accident.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.987-991
• /
• 2005

The Aerial platform Truck is widely used for work in high place with the aerial platform. The most important thing is that worker's safety and worker must be able to work with trustworthiness so it needs to be verified its stiffness, deflection of boom, and dynamic condition concerned with a rollover accident. It should have an analytical exactitude because it is directly linked with the worker safety. In this point, we are trying to develop a proper CAE analysis model concerned with a rollover safety, bending stress and deflection for load. The Aerial platform Truck have a dynamic characteristics by load and moving of boom in the work field, so its static and dynamic strength analysis, structural mechanics are very important. Therefore, we evaluate the safety of each boom to calculating its stress, deflection. A computer simulation program is used widely for doing applying calculation of stiffness and structural mechanics, then finally trying to find a optimum design of the Aerial platform Truck.

• Wind and Structures
• /
• v.26 no.1
• /
• pp.35-43
• /
• 2018

This paper describes the effect of different testing parameters (configuration of infrastructure and truck position on road) on truck aerodynamic coefficients under cross wind conditions, by means of a numerical approach known as Large Eddy Simulation (LES). In order to estimate the air flow behaviour around both the infrastructure and the truck, the filtered continuity and momentum equations along with the Smagorinsky-Lilly model were solved. A solution for these non-linear equations was approached through the finite volume method (FVM) and using temporal and spatial discretization schemes. As for the results, the aerodynamic coefficients acting on the truck model exhibited nearly constant values regardless of the Reynolds number. The flat ground is the infrastructure where the rollover coefficient acting on the truck model showed lowest values under cross wind conditions (yaw angle of $90^{\circ}$), while the worst infrastructure studied for vehicle stability was an embankment with downward-slope on the leeward side. The position of the truck on the road and the value of embankment slope angle that minimizes the rollover coefficient were determined by successfully applying the Response Surface Methodology.

• Structural Engineering and Mechanics
• /
• v.49 no.3
• /
• pp.395-410
• /
• 2014

Fiber Reinforced Elastomeric Bearings (FREBs) are a relatively new type of laminated bearings that can be used as seismic/vibration isolators or bridge bearings. In an unbonded (U)-FREB, the bearing is placed between the top and bottom supports with no bonding or fastening provided at its contact surfaces. Under shear loads the top and bottom faces of a U-FREB roll off the contact supports and the bearing exhibits rollover deformation. As a result of rollover deformation, the horizontal response characteristics of U-FREBs are significantly different than conventional elastomeric bearings that are employed in bonded application. Current literature lacks an efficient analytical horizontal stiffness solution for this type of bearings. This paper presents two simplified analytical models for horizontal stiffness evaluation of U-FREBs. Both models assume that the resistance to shear loads is only provided by an effective region of the bearing that sustains significant shear strains. The presented models are different in the way they relate this effective region to the horizontal bearing displacements. In comparison with experimental results and finite element analyses, the analytical models that are presented in this paper are found to be sufficiently accurate to be used in the preliminary design of U-FREBs.

• Journal of Auto-vehicle Safety Association
• /
• v.13 no.3
• /
• pp.47-53
• /
• 2021

This study is a study to estimate the VSL (Value of a Statistical Life) and CBA (Cost-benefit analysis) of the rollover safety standard for hydrogen buses, VSL is an economic value concept used to quantify the benefits of avoiding death. CBA shows the effect of cost-benefit, and if B/C is greater than 1, there is a social effect. In order to estimate the VSL and CBA, the hydrogen bus introduction scenario was assumed to be optimistic (20,000 vehicles in 2030), neutral (15,000 vehicles in 2030), and pessimistic (10,000 vehicles in 2030), and the effect of reducing human casualties was estimated. As a result, except for the pessimistic market situation of introducing hydrogen buses (10,000 vehicles in 2030) and the VSL reduction ratio of 10%, all policies were judged to have high cost-benefit effects. These results indicate that the introduction of the rollover safety standard for hydrogen buses is a socially effective policy.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.11
• /
• pp.7329-7334
• /
• 2015

This is to analyze of driver behavioral and the accident characteristics in rollover. The study period was January 2011 to May 2014 and the subject of study was 102 person who were drivers visited the emergency room. Research tool includes a damage information of the vehicle, accident mechanism, damage to the patient clinical information with the injury data from the ROAD Traffic Authority. For data analysis, SPSS 18.0 was used for t-test, ANOVA and Chi-square test. Injury Severity Score average score according to the vehicle type is 6.00 points in the smaller vehicle, at high vehicle 11.78 points, from the other vehicle that showed 14.70 points. Significant differences between the three groups did not show (P=.267). Men did not use a seat belt significantly compared to women(P=.007). Vehicle type and weather, this was no correlation with whether or not use the seat belt(P=.755, P=.793). But showed a tendency to smaller size vehicles drivers do not use a seat belt, the weather could see a little more inclined to use a seat belt rather than a sunny day. Finally, in rollover accidents as in other types of accident it was confirmed that the seat belt has a great influence on the damage.

• Journal of Industrial Technology
• /
• v.18
• /
• pp.225-232
• /
• 1998

Train crashes involve complex interaction between deformable bodies in multiple collisions. The purpose of this study is to suggest the effective analytical procedure using finite element model for the crashworthiness of motorized trailer of high speed train. Various types of crash events are investigated and the conditions for numerical simulation are defined. Finally korean high speed train which consists of aluminum members can be analyzed and designed by the numerical simulation.