• 한국철도학회논문집
• /
• 제9권5호
• /
• pp.618-623
• /
• 2006

Understanding the contact between wheel and rail is a starting point in railway vehicle dynamic research area and especially analysis for the contact geometry between wheel and rail is important. On the one hand, the critical speed as the natural characteristics of rolling-stock is generally tested on the roller rig. The geometrical characteristics of the wheel/roller contact on the roller rig are different from these of the general wheel/rail contact because the longitudinal radius of roller is not infinite compared with rail. Thus, in this paper we developed the algorithm to analyze the wheel/roller contact geometry of our roller rig which is constructed now and analyzed the difference between whee/roller contact and wheel/rail contact. In conclusion, we found that the yaw motion of wheelset and the roller radius influence the geometrical contact parameters in wheel flange contact area.

• 한국산업보건학회지
• /
• 제7권1호
• /
• pp.87-98
• /
• 1997

In this study, subway train vibration has been measured to characterize the whole body vibration of Seoul subway lines for various human postures. Results show that the floor vibration level of the subway trains in the vertical direction is higher than that in other directions. At the standing human posture, vibration level of the head in the right-left direction are increased while that in the vertical direction is decreased. It is assumed that the different flexibility of the human body and the rolling motion of the subway trains are the main cause. At the sitting posture with back seat on, vibration level in the right and left direction at the human ischial tuberosities is lower than that in other directions. Results also show that there were little difference between back-seat on model and back-seat off model. Transmissibility analysis shows how the subway vibration affects the response of a human body.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1995년도 춘계학술대회논문집
• /
• pp.252-263
• /
• 1995

It is visualized that dislocations move straightly in polycrystalline structure and the trans-grain dislocation moving occur from yield point to ultimate tensile stress. Some fracturemodes in uniaxial tensile test are ilustrated in order to explain that after the ultimate point the grains deforms by twins and the rotations of grains make cracks at the grain-boundaries by the incompatibility . The luders banks. which propagates along the axis of the specimen, are twin bands whcih are formed by rearrangement of the atoms within the structure of three-dimensional crystallizing $\pi$-bondings. The fatigue limit can be found through the atom's rolling back motion during elastic deformation inthe uniaxial tensile test by the change of the gradient.

• Journal of Mechanical Science and Technology
• /
• 제19권spc1호
• /
• pp.377-387
• /
• 2005

The equations of motion of two-wheeled vehicles, e.g. bicycles or motorcycles, are developed by using Lagrange's equations for quasi-coordinates. The pure rolling constraints between the ground and the two wheels are considered in the dynamical equations of the system. For each wheel, two nonholonomic and two holonomic constraints are introduced in a set of differential-algebraic equations (DAE). The constraint Jacobian matrix is obtained by collecting all the constraint equations and converting them into the velocity form. Equilibrium, an algorithm for searching for equilibrium points of two-wheeled vehicles and the associated problems are discussed. Formulae for calculating the radii of curvatures of ground-wheel contact paths and the reference point are also given.

• 한국공작기계학회논문집
• /
• 제11권3호
• /
• pp.80-85
• /
• 2002

The free curve gear is a non-circular gear without any relating center, which can perform free curve motion for complicated mechanisms, and minimize the work area. In this study, an algorithms for tooth profile generation of free curve involute gear is developed. The algorithm uses the involute gear creating principle in which a gear can be generated by rolling with another standard involute one. Cycloid me and third polynomial curve gears were designed and verified by computer graphics. These gears are manufactured in the wire-cut EDM and examined in engagement with a standard spur gear. The results showed that the proposed algorithm is successful to design and to manufacture the free curve gear with concave and convex profiles.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 1998년도 춘계학술발표회 논문집
• /
• pp.56-63
• /
• 1998

A fiber optic gyrocompass for ships was made in consideratino of cost, reliability and convenience. In order to reduce the cost a cheaper fiber sensor was used inthis system. The accuracy was increased by replacing a 180ppr-slit disk with a 1000ppr-encoder. The reliability was also increased by improving the signal processing electronics. This system was made as a heading angle display type for convenience. Although more inexpensive FOG than that of the previous system was used , the accuracy of this compass was increased about 0.5$^{\circ}$. Moreover, it has a very fast warm-up time of about 5minutes. Therefore, this compass can show the prospect of proactical use on ships if it is installed ona stabilizer against the dynamic motion such as rolling and pitching.

• 한국정밀공학회지
• /
• 제26권12호
• /
• pp.47-54
• /
• 2009

A worm screw is widely used in a geared motor unit for motion conversion from rotation to linear. For mass production of a high quality worm, the current rolling process is substituted with the milling process. Since the milling process enables the integration of all operations of worm manufacturing on a CNC(Computer Numerical Control) lathe, productivity can be remarkably improved. In this study, the tooling system for planetary milling on a CNC lathe to improve machinability is developed. However, the cutting tool-workpiece interference is important factors to be considered for producing high quality worms. For adaptability of various worms machining, the tool-workpiece interference simulation system based on a tool-tip trajectory model is developed. The developed simulation system is verified through several kinds of worms and experimental results.

• Design & Manufacturing
• /
• 제2권4호
• /
• pp.11-15
• /
• 2008

In the sheet metal forming using a high speed press machine, driving device, such as crank, link, and knuckle mechanism, has to be designed in consideration of impact at a moment when press die contact with material, because the impact affects a dimensional accuracy of products and a life span of press die. In this study, dynamic analysis was performed using numerical simulation in order to verify the impact reduction effect for proposed double knuckle mechanism by estimating rolling and pitching moment of slide.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 A
• /
• pp.249-251
• /
• 1994

This paper introduces an implementation of high performance voltage source inverter system based on 16bit micro-processor and DSP for the application to modem rolling stock traction system. In contrast with other industry oriented inverter system, this system requires precise control action complying with various load condition and high overload capability. An asynchronous PWM generation and 3' pulse mode technology are adopted in order to improve compliant starting torque characteristics at starting phase and soft backward-forward starting motion.

• 한국군사과학기술학회지
• /
• 제13권1호
• /
• pp.22-29
• /
• 2010

In this study, computational multi-body dynamics and structural vibration analyses including some impact condition have been conducted for the ground flight test system of the developed smart UAV model. Designed ground test system has four degree-of-freedom motions with limited motion control mechanism. Design safety margin designs for several structural components are tested and verified considering expected critical motions (pitching and rolling) of the test smart UAV model. Computational results for various analysis conditions are practically presented in detail. Futhermore, proper design modifications of the initially designed test equipment in order to guarantee or increase structural safety have been successfully conducted in the design stage.