• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.878-882
• /
• 2004

We investigated the effect of weld details on fatigue behavior of a material, JIS SM 490 A, with yielding strength of about 350 MPa and tensile strength of about 520 MPa. Tensile tests, instrumented indentation tests and fatigue tests were carried out on double V-grooved butt weld plates such as reinforcement removed, as-welded and weld toe ground. In addition plates with transverse fillet welded web, load carrying cruciform fillet welded plates, non-load-carrying cruciform fillet welded plates, longitudinal butt welded plates and welded rectangular life-size box beams were tested. S-N curves for the above specimens were obtained and analyzed.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.04a
• /
• pp.19-24
• /
• 1997

The operating torque and tribological characteristics of the cam/tappet system in an I.C. engine have an important effect on engine efficiency. In this paper, we measured the torque of cam/tappet system with respect to the oil temperature and camshaft speed to characterize the tribological behavior. Also, accelerated test was performed to analyze the wear characteristics of cam/tappet interface. The torque of the cam/tappet system decreased with respect to camshaft speed and was not significantly affected by the oil temperature. The results of accelerated test showed that the running-in wear occurred during the tests and the center of the tappet was mainly damaged by the rolling and sliding friction.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.820-824
• /
• 1997

In order to investigate the effect of surface treatment(Anodizing) and rolling in Al 5083-H131 alloy, ballistic testing was conducted. Ballistic resistance of these materials. was measured by protection ballistic limit(V$_{50}$), a statical velocity with 50% probability for incomplete penetration. Fracture behaviors and ballistic tolerance, described by penetration modes, are observed respectfully, resulting from V$_{50}$ test and Projectile Through Plates(PTP) test at velocities greater than V$_{50}$. PTP tests were conducted with 0$^{\circ}$obliquity at room temperature were also conducted with projectiles that were able to achieve near or complete penetration during PTP tests. Resistance to penetration, and penetration modes of Al 5052-H34 alloy, compared to those of Al 5083-H131 alloy.alloy.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.267-272
• /
• 2003

In order to investigate the effect of face material on Ti/Al alloy laminates under high velocity impact, a ballistic testing was conducted. Ballistic resistance of these materials was measured by protection ballistic limit($V_{50}$), a statistical velocity with 50% probability penetration. Fracture behaviors and ballistic tolerance, described by penetration modes, were respectfully observed, by $V_{50}$ test and Projectile Through Plates (PTP) test at velocities greater than $V_{50}$. PTP tests were conducted with $0^{\circ}$obliquity at room temperature using 5.56mm ball projectile. $V_{50}$ tests with $0^{\circ}$obliquity were also done with projectiles that were able to achieve near or complete penetration during PTP tests. Resistance to penetration, and penetration modes which face material was Titanium alloy, were compared to those which face material was anodized Al alloy after cold-rolling.

• Journal of Mechanical Science and Technology
• /
• v.19 no.4
• /
• pp.976-984
• /
• 2005

This paper presents the analysis results of dynamics in the billiards game within the frame­work of rigid-body mechanics and a numerical simulation program. The friction exists between the ball and the table bed as well as between the ball and the rail. There are three parts in the dynamic behavior of the ball on the table bed; motion of the ball on the table bed, collision between balls, and collision between the ball and the cushion. During the development of the simulation program, the dynamics problems such as rolling motion and three-dimensional frictional impact motion have been analyzed in detail. The theoretical issues are implemented into a viable graphic simulation program and its efficacy is demonstrated through the experi­mental validation of the billiards game. The resulting analysis results are verified quantitatively and qualitatively using high-speed video camera. Through the experimental tests, it was found that the physical parameters such as coefficients of restitution and friction vary according to the motion variables and corresponding empirical formulations were developed. The simulation and experimental results agree well.

• Asian Journal of Turfgrass Science
• /
• v.11 no.1
• /
• pp.23-31
• /
• 1997

The K+ and Na+ contents in the guard cells of Agave which had a characteristic of CAM plant were measured by using "Rolling technique". That results were correspond with the change of the stomatal aperture width. That is to say, stomatal movement of Agave is due to the change of K+and Na+ concentration in the guard cells. As Agave which was used in this experiment showed two peaks of which one was at 3 hour and the other was at 24 hour in stomatal aperture width, it was seemed that Agave had both characteristics of CAM and $C_3$pattern.

• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.743-748
• /
• 2007

The important factor to evaluate the running safety of a railway vehicle would be the interaction force between wheel and rail(derailment coefficient), for which is one of important factors to check the running safety of a railway vehicle that may cause a tragic accident. Especially, a newly developed vehicle that first runs commercially requires necessarily the measurement and evaluation of derailment coefficient for securing the safety of a vehicle while measuring the derailment coefficient in view of securing running safety could be the more important factor than any other factors. In this paper, examined possibility that can forecast derailment possibility to behavior of only vibration and displacement by measuring vibration acceleration and displacement in vehicles that travel actuality rail track, and compares with data of wheel load/lateral force result.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.30-35
• /
• 2010

The railway vehicle is a multi-body system running on the track which consists of carbody, bogie and wheelset, each of components is connected with rigid mass, spring and damper. each of components has translation motions of longitudinal (X axis), lateral(Y axis) and vertical(Z axis) direction, and rotation motions of X, Y, Z axis which are named Rolling, Pitching and Yawing. The vibration mode of railway vehicle is difficult to find the characteristics of motion during the operation on the track because these happen to independence or duplication motion caused by vehicle, wheel/rail and track irregularity etc. This paper presents the result of ramp test to show the bounce, roll, pitch and yaw mode frequency of the railway vehicle.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.249-252
• /
• 1997

Mini-mill process which is one of the new steel making process to be able to produce the hot rolled strip by thin slab caster, was completed in the kwangyang steel work. The new process was constructed liquid core deduction, tandem reduction unit, induction heater, coil box and finishing mill to be varied width. Therefore, in oder to make sure of target strip width, analysis of actual plant data was done to fine out amount of width deviation. Finally, the predication system of width in the mini-mill process was developed to included temperature caculation model.

• Journal of Mechanical Science and Technology
• /
• v.20 no.5
• /
• pp.621-633
• /
• 2006

To reflect the size effect of material $(1\sim15{\mu}m)$ during plastic deformation of polycrystalline copper, a constitutive equation which includes the strain gradient plasticity theory and intrinsic material length model is coupled with the finite element analysis and applied to plane strain deformation problem. The method of least square has been used to calculate the strain gradient at each element during deformation and the effect of distributed force on the strain gradient is investigated as well. It shows when material size is less than the intrinsic material length $(1.54{\mu}m)$, its deformation behavior is quite different compared with that computed from the conventional plasticity. The generation of strain gradient is greatly suppressed, but it appears again as the material size increases. Results also reveal that the strain gradient leads to deformation hardening. The distributed force plays a role to amplify the strain gradient distribution.