• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.260-260
• /
• 2000

In this work, we have developed a 2 degree of freedom(DOF) motion simulator that can generate the sensation of motion in a 6 DOF space. The motion base has the DOF of roll and pitch, and the purpose of the motion base is to create the sensation of riding a vehicle in a 3D space by controlling the motion base. The dynamics of the mechanism was analysed and the optimal design of the motion base mechanism has been reached. The prototype motion base mechanism was developed and tested. The multi-axis motion controller(MMC) was used to control the two ac servo motors that drive the roll and pitch motion.

• Journal of Audiology & Otology
• /
• 제25권1호
• /
• pp.43-48
• /
• 2021

Background and Objectives: Conflicting mechanisms have been reported about spontaneous reversal of positional nystagmus during head-roll maneuver in patients with benign paroxysmal positional vertigo (BPPV). The objective of this study is to review the reports about the characteristics and possible mechanisms of reversing positional nystagmus and to present seven new cases. Subjects and Methods: Seven cases (5 males, 2 females; 4 left-sided, 3 right-sided) were recruited among 732 patients with BPPV seen outpatient clinic between 2009 and 2019. Diagnosis of lateral canal canalolithiasis was confirmed when transient geotropic nystagmus was documented during head-roll test. Reversing positional nystagmus was analyzed in each case and clinical characteristics of the patients were documented. Results: The age of patients was ranging between 30 to 64 years (46.44±10.91). Duration of symptoms was short (21.34±19.74). Six of them had a story of head trauma. Initial latency was short. First, intense geotropic nystagmus was observed following provocative head-roll position on the affected side. There was short "silent phase". Then, a longer second-phase of reversed nystagmus was noted. Total duration of nystagmus was 78.40±6.82 seconds. Maximal slow phase velocity was 24.05±6.34 deg/sec. All patients were cured with barbeque maneuver. Conclusions: Ipsilateral reversing positional nystagmus during head-roll maneuver is due to lateral canal canalolithiasis. Mechanism is likely to be due to endolymphatic double flow. Bilateral cases may be due to simultaneous co-existence of canalolithiasis and cupulolithiasis. Longer recording of nystagmus is recommended not to miss the cases with spontaneous direction-changing positional nystagmus.

• 대한청각학회지
• /
• 제25권1호
• /
• pp.43-48
• /
• 2021

Background and Objectives: Conflicting mechanisms have been reported about spontaneous reversal of positional nystagmus during head-roll maneuver in patients with benign paroxysmal positional vertigo (BPPV). The objective of this study is to review the reports about the characteristics and possible mechanisms of reversing positional nystagmus and to present seven new cases. Subjects and Methods: Seven cases (5 males, 2 females; 4 left-sided, 3 right-sided) were recruited among 732 patients with BPPV seen outpatient clinic between 2009 and 2019. Diagnosis of lateral canal canalolithiasis was confirmed when transient geotropic nystagmus was documented during head-roll test. Reversing positional nystagmus was analyzed in each case and clinical characteristics of the patients were documented. Results: The age of patients was ranging between 30 to 64 years (46.44±10.91). Duration of symptoms was short (21.34±19.74). Six of them had a story of head trauma. Initial latency was short. First, intense geotropic nystagmus was observed following provocative head-roll position on the affected side. There was short "silent phase". Then, a longer second-phase of reversed nystagmus was noted. Total duration of nystagmus was 78.40±6.82 seconds. Maximal slow phase velocity was 24.05±6.34 deg/sec. All patients were cured with barbeque maneuver. Conclusions: Ipsilateral reversing positional nystagmus during head-roll maneuver is due to lateral canal canalolithiasis. Mechanism is likely to be due to endolymphatic double flow. Bilateral cases may be due to simultaneous co-existence of canalolithiasis and cupulolithiasis. Longer recording of nystagmus is recommended not to miss the cases with spontaneous direction-changing positional nystagmus.

• 반도체디스플레이기술학회지
• /
• 제9권2호
• /
• pp.103-109
• /
• 2010

An ink transfer is modeled and experimentally verified using roll-to-roll electric direct gravure printing process. The ink transfer model based on the physical mechanism for the maximum ink transfer rate is proposed, and experimented by the electric printing machine in FDRC for the relations of the maximum ink transfer rates to the printing pressure, the operating speed, the operating tension, the surface roughness of substrates, and the contact angle between substrate and silver ink. The free ink split coefficient and immobilized ink under the maximum ink transfer rate are calculated by the physical parameter in a printing process and contact angle between substrates and ink. Numerical simulations and experimental studies were carried out to verify performances of the proposed ink transfer model. Results showed that the proposed ink transfer model was effective for the prediction of the amount of transferred ink to the substrate in a direct gravure printing systems.

• 한국철도학회논문집
• /
• 제14권3호
• /
• pp.203-210
• /
• 2011

본 논문에서는 열차 충돌로 발생되는 충격으로 차축에 큰 수직하중 및 수평하중이 부과될 때 플랜지가 레일을 타고 오르는 탈선현상을 예측할 수 있는 단일 윤축의 이론적 탈선 모델을 연구하였다. 철도차량 충돌 시 크게 타고오름(wheel-climbing), 들려오름(lift-up), 전복(roll-over) 등과 이들의 복합유형탈선이 발생할 수 있다. 타고오름 및 복합 유형의 탈선은 세 가지(Climb-over, Climb/roll-over, Roll-over)로 정의할 수 있다. 본 논문에서는 충돌 후 탈선거동을 예측하기 위하여 타고오름 및 복합 유형 탈선에 대한 단일윤축 이론모델을 제안하고, 정의한 세 가지 탈선거동이 발생하기 위한 조건을 제시하였다. 타고오름 및 복합 유형의 탈선거동을 예측하기 위하여 제안된 단일윤축 이론모델의 타당성을 단순플랜지 형상 윤축모델을 사용한 동역학 시뮬레이션을 통하여 검증하고, 타당성을 보인다.

• 한국주조공학회지
• /
• 제43권2호
• /
• pp.55-63
• /
• 2023

Due to the importance of the surface on the final slab quality, it is essential to maintain a smooth segment roll surface that is in touch with the thin solid shell during solidification. In this paper, the surface of the used continuous casting guide roll was analyzed to realize the mechanism of its surface deterioration. Surface analysis has revealed severe corrosion at two distinct areas leading to deep roughness occurring on the guide roll. Firstly, the severe corrosion follows prior austenite grain boundary due to exposure with acidic environment. Also, in heat affected zone (HAZ) where two cladding beads overlap, more severe corrosion takes place. The overheat input results in local ferritization without full melting which increases retained δ-ferrite content almost 10 times higher than surrounding area. Corrosion was observed to happen at the δ-γ interface where Cr depletion takes place.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.65-66
• /
• 2006

Dancer systems are most widely used mechanism for attenuation of tension disturbances. Lately, demands fur high speed converting machines over 500mpm(m/min) are raising but domestic converting industries can not come up with the machines because capacities for a designing of the converting machine are restricted lower than 300mpm. Moreover roll-to-roll is attracted flexible display manufacturer's attention as a effective method for productivity. A constant tension level in the span before the first printing cylinder is the key of high speed quality printing. This paper presents a modeling and simulations of dancer systems on converting machines.

• 한국광물학회지
• /
• 제23권4호
• /
• pp.297-303
• /
• 2010

본 연구에서는 파쇄 메커니즘이 상이한 파쇄기(함마 크럿셔와 롤 크럿셔)와 파쇄회로(개회로 및 폐회로)를 사용하여 각각의 파쇄기 종류에 따른 백운석 파쇄산물의 입도분포와 파쇄특성에 대해 알아보았다. 함마 크럿셔로 파쇄한 경우, 100 mesh 이하의 미분이 약 34 wt.%로 롤 크럿셔로 파쇄한 경우보다 약 3 배 이상 높았다. 또한 14~25 mesh 산물은 롤 크럿셔로 파쇄할 경우, 함마 크럿셔로 파쇄한 경우에 비하여 약 20 wt.% 이상 많이 생성되었다. 35 mesh 이하의 산물은 함마 크럿셔로 파쇄 시 전체의 약 80 wt.% 정도였다. 두 파쇄기 모두 개회로에 비해 폐회로 파쇄 시 미분의 발생률이 감소하였다. 광석에 따른 적절한 파쇄기 및 파쇄회로의 선택에 따라 목적하는 입도의 산물을 효율적으로 얻을 수 있다.

• Tribology and Lubricants
• /
• 제33권6호
• /
• pp.256-262
• /
• 2017

Molten zinc plating is a process in which zinc is thinly coated over a metallic or non-metallic surface. It is used in various industrial fields for corrosion resistance and decoration. During the process, a steel sheet is passed through a roll that rotates inside the molten zinc liquid in the temperature range of $460^{\circ}C$ to $680^{\circ}C$, and the plating liquid flows into the roll causing abrasion and erosion of the roll surface. This problem is known to accelerate the replacement cycle of the roll and cause considerable economic loss owing to production line stoppage. Here, we propose a mechanism that operates at high temperature and pressure with a labyrinth type seal design to resolve this problem. We theoretically investigate the flow of the plating solution inside the seal and compute the minimum rotation speed required to prevent the plating solution from entering the seal chamber. In addition, we calculate the thermal deformation of the seal during operation and display thermally deformed dimensions at high temperatures. To verify the theoretical results, we perform experiments using pilot test equipment working in the actual plating environment. The experimental results are in good agreement with theoretical results. We expect our results to contribute towards the extension of the roll's life span and thereby reduce the economic losses.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.373-382
• /
• 1999

Nucleation and growth process of sticking particle in ferritic stainless steels was investigated using a two disk type hot rolling simulator. The sticking behavior was strongly dependent on the surface roughness of a high speed steel roll(HSS) and the oxidation resistance of the ferritic stainless steels. A hot rolling condition with the lower oxidation resistance of the stainless steel and the higher surface roughness of HSS roll was more sensitive to sticking occurrence. It was also illucidated that the initial sticking particles were nucleated at the scratches formed on the roll surface and were served as the sticking growth sites. As rolling proceeded, the sticking particles grew sites. As rolling proceeded, the sticking particles grew by the process that the previous sticking particles provided the sticking growth sites.