• 국제강구조저널
• /
• 제18권5호
• /
• pp.1631-1638
• /
• 2018

In the periodic repainting of steel bridges, often the steel surface has to be prepared by using power tools to remove surface contaminants, such as deteriorated paint film and rust, and to increase the adhesive strengths of the paint films to be applied newly. Surface preparation by bristle roll-brush grinding, which is a type of power tool, may additionally introduce compressive residual stress and increase the fatigue resistance of welded joints owing to the impact of rotating bristle tips. In this study, fatigue tests were conducted for longitudinally out-of-plane gusset fillet welded joints and transversely butt-welded joints to evaluate the effect of bristle roll-brush grinding prior to repainting on the fatigue resistance of the welded joints. The test results showed that bristle roll-brush grinding introduced compressive residual stress and significantly increased fatigue limits by over 50%.

• Journal of Biosystems Engineering
• /
• 제13권3호
• /
• pp.71-80
• /
• 1988

• 지구물리와물리탐사
• /
• 제22권4호
• /
• pp.177-185
• /
• 2019

육상 탄성파 탐사자료에서 쉽게 관찰되는 그라운드 롤은 표면파의 일종으로 대표적인 일관성 잡음이다. 반사파 자료처리 과정에서 그라운드 롤은 잡음에 해당하기 때문에 제거하게 되는데, 반사 신호와 중첩되는 경우 반사파 신호음이 손상되는 문제가 발생한다. 본 연구에서는 반사 신호음 손실을 줄이면서 그라운드 롤을 효과적으로 억제할 수 있는 방법을 찾기 위해 카루넨-루베 변환을 중심으로 살펴보고 그 결과를 분석하였다. 균질 탄성매질에서 구한 인공자료 수치 모형 실험에서 그라운드 롤이 뚜렷하게 감소된 것을 확인할 수 있으나 현장자료 적용실험에서는 띠통과 필터링 결과와 큰 차이점을 발견할 수 없었다. 이러한 현상은 현장자료에서 여러 주파수 대역을 포함하고 있는 그라운드 롤에 대해 선형 수평정렬 모음(Linear moveout gather)을 계산하기 어렵기 때문으로 여길 수 있다. 이에 비해서 특이값 분해 필터링 결과는 그라운드 롤이 상당부분 감소되었음을 확인할 수 있었다. 특이값 분해 필터링은 반사파를 중심으로 정규 수평정렬 모음(Normal moveout gather)을 계산하기가 쉬워 카루넨-루베 변환 필터링 보다 그라운드 롤 억제효과가 큰 것으로 여겨진다.

• Corrosion Science and Technology
• /
• 제9권3호
• /
• pp.116-121
• /
• 2010

For over a decade, research and development on submerged hardware in continuous galvanizing pots has been carried out at Teck's Product Technology Centre. The outcome of numerous laboratory tests and field trials has demonstrated that dissimilar materials with comparable surface hardness are most suitable for the manufacture of roll bearings. Wear debris can be easily retained in bearings made of the same material, thereby negatively affecting bearing performance and service life. Bearings made of the same materials are also vulnerable to catastrophic failures. The dissolution of iron from the coated strip creates an iron-rich zone associated with a high concentration gradient in the vicinity of the sink roll. Consequently, the sink roll becomes a preferential site for dross pick-up. In operations involving extremely high temperatures, such as in Galvalume production, the material selection for pot hardware is immaterial to the final corrosion product of the hardware and the pick-up on the hardware.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1126-1131
• /
• 2007

This paper presents unified chassis control (UCC) to improve the vehicle lateral stability. The unified chassis control implies combined control of active front steering (AFS), electronic stability control (ESC) and continuous damping control (CDC). A direct yaw moment controller based on a 2-D bicycle model is designed by using sliding mode control law. A direct roll moment controller based on a 2-D roll model is designed. The computed direct yaw moment and the direct roll moment are generated by AFS, ESP and CDC control modules respectively. A control authority of the AFS and the ESC is determined by tire slip angle. Computer simulation is conducted to evaluate the proposed integrated chassis controller by using the Matlab, simulink and the validated vehicle simulator. From the simulation results, it is shown that the proposed unified chassis control can provide with improved performance over the modular chassis control.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.384-388
• /
• 1997

Recently,direct rolling process has been drawing increasing interests because production cost be greatly reduced by eliminating subsequent hot rolling processes. Such a process has been characterized to prosuce thin steel strip (thickness 1~5mm) directly from molten metal and to skip over the conventional hot rolling processes. However, since there are several process parameters, which affect the quality of product,and their relationship between the parametersare very complex,it is therefore very difficult to realize the process design and the quality control. To overcome these difficulties quantitative relationship between the parameters are investigated through a numerical analysis. Form these results, it is found that solidification final point is the most important paramter which is critical to quality of the strip. Also,the multiple regression model is obtianed to determine their relationship from the solidification final point and roll separating force which can be easily estimated

• 한국통신학회논문지
• /
• 제21권11호
• /
• pp.2942-2953
• /
• 1996

This paper studies the effect of intersymbol interference due to sampling-time jitter on the worst-case bit error probability in a digital modultation over an additive white Gaussian noise channel, with the squared-root raised-cosine filters in the transmitter and the receiver. It derives approximation formulas using the Taylor series approximations. the principal results of this paper is the relationship between the worst-casse bit error probability, the degree of jitter, the roll factor of the raised cosine filter, and other quantities. Numerical results show, as expected, that the intersymbol interference decreases as the roll-off factor increases and the jitter decreases. They also show that the approximation formulas are accurate for smally intersymbol interference, i.e., for large roll-noise ratio $E_{b/}$ $N_{0}$.leq.7 dB and begin to lose accuracy for larger signal-to-noise ratio.o.o.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.78-87
• /
• 1999

A mathematical model for the stress free surface profile in Over-Round and Round-Oval grove rolling, which can be used effectively in the calculation of pass area, is presented. The new model has generality, simplicity and accuracy for practical usage. The stress free surface profile of an outgoing stock can be modeled when the maximum spread of it known a priori. The equation for the stress free surface profile is formulated from the linear interpolation of the radius of curvature of an incoming stock and that of roll groove to the axis direction. In developing the analytical model, the effect of rolling temperature and friction between roll and work piece(stock) were not considered since the geometry of roll groove and the incoming work piece were assumed a dominant factor which decides the stress free surface profile of the outgoing stock. A simulation with the analytical model developed also has been carried out to demonstrate the stress free surface profile of the outgoing stock.

• 한국정밀공학회지
• /
• 제28권10호
• /
• pp.1131-1140
• /
• 2011

A new rotary gravure-offset printing unit is constructed by paralleling a gravure plate cylinder, a blanket cylinder and a impression roller. A Muti-Unit Gravure-Offset Printing Press(MUGOP) equipped with a series of the 3 printing units is utilized for roll-to-roll fine printing. Its core technology is precise over-piling printing of fine patterns. The severe problems of 'slurring' and 'doubling' in typical offset printing are unavoidable, which can be eliminated by applying a soft pad-type blanket cylinder and the unique 'true rolling' technique. Nip pressure between the blanket cylinder and the plate cylinder is measured by the constant pressure control system which equipped with load cells attached on the cylinders' axes. The running circumference of the blanket cylinder is increased to reach the same circumference of the plate cylinder as the pressure increasing, so that the specifications of the blanket cylinder is determined by the relationships of its shore hardness, diameter and nip pressure. When a softer blanket is used, a blanket cylinder of smaller diameter could give higher nip pressure. Realization of the true rolling technique on the MUGOP makes multilayer printing possible as well as fine printing in printed electronics.

• 대한기계학회논문집A
• /
• 제28권7호
• /
• pp.992-998
• /
• 2004

During the tube hydropiercing, the region adjacent to the pierced hole will be deformed and will be drawn away from the die block as the punch advances through the wall of the tube. The deformation in the region may range from a substantially flat form to a countersunk form, so called rollover. In this study, the effects of material properties, shape of piercing punches, roundness of tube surface and internal pressure within the tube during piercing on the rollover have been investigated experimentally. The results provide the quantitative variation of rollover at given hydropiercing parameters, and a relationship between the deformed radius and the rollover caused by the deformation has been established.