• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1103-1108
• /
• 2007

This paper describes a robust model-based roll state estimator for application to the detection of impending vehicle rollover. The roll state estimator is based on a 2-D bicycle model and a roll model to estimate the maneuver-induced vehicle roll motion. The measurement signals are lateral acceleration, yaw rate, steering angle, and vehicle speed. Vehicle mass is adapted to obtain robust performance of the estimator. Computer simulation is conducted to evaluate the proposed roll state estimator by using a validated vehicle simulator. It is shown that the roll state estimator shows robust performance without exact vehicle mass information.

• Ocean Systems Engineering
• /
• v.5 no.2
• /
• pp.55-76
• /
• 2015

Of all the six degrees of freedom, the roll motion of a ship is the most poorly understood and displays complicated phenomena. Due to the low potential wave damping at the natural frequency, the effective analysis of ship roll dynamics comes down to the accurate estimation of the viscous roll damping. This paper provides overview of the importance of roll damping and an extensive literature review of the various viscous roll damping prediction methods applied by researchers over the years. The paper also discusses in detail the current state of the art estimation of viscous roll damping for ship shaped structures. A computer code is developed based on this method and its results are compared with experimental data to demonstrate the accuracy of the method. While some of the key references describing this method are not available in English, some others have been found to contain typographic errors. The objective of this paper is to provide a comprehensive summary of the state of the art method in one place for future reference.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.9
• /
• pp.681-689
• /
• 2020

This paper presents methods and results of both flight test examining roll angle estimation performance of slowly rolling munition forced to spin in the air, and fabricating a replica of guided munition. Guided munition was deployed from multi rotor type UAV mother ship whose altitude and velocity was conveyed to it as initial state. Flight test scenario is composed of a sequence of munition drop(deployment), munition spin, roll angle estimation and stabilization. Munition was deployed from mother ship at around 200m high with horizontal velocity of 15m/s, and was made spun using internal reaction wheel. Performance analysis on roll angle estimation is provided in comparison with commercial aerospace graded GPS/INS. Moreover, several mechanisms that rotates munition using reaction wheel, and actual product that realizes one of them are introduced.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.5
• /
• pp.373-381
• /
• 2021

This paper details the result of flight experiment that examines performance of roll angle estimation algorithm of slowly rolling munition taking time delay of measurement into account when measurement comes in delayed fashion. As the measurement is passed through low pass filter for numerical stabilization and de-noising purpose which induces time delay, we design augmented state Kalman filter that incorporates distribution models of stochastic delay over time. Flight experiment was conducted to verify the algorithm at around 250m high AGL(Above Ground Level) conveying velocity of 28m/s from fixed-wing mother plane to the munition. Munition was made spun with respect to its roll axis using internal reaction wheel afterward. Numerical comparison of proposing method's roll estimation performance with that of commercial aerospace graded GPS/INS shows that proposed filter design can effectively compensate time delay of measurement.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1864-1866
• /
• 1997

Uncertainties in the aerodynamic coefficients or time delay effects in implementing an autopilot algorithm can make a Flight Control System(FCS) unstable. When a FCS enters unstable state, the actuator or sensor limiters in FCS make the unstable system not diverge but be in the state of stable limit cycle. If an autopilot recognize the FCS to be in the stable limit cycle phenomenon, it woudl be better to adjust autopilot gains to stabilize the FCS. A novel method to stabilize a FCS using parameter estimation and maintenance of given phase margin is proposed. The method is applied to roll control loop and verified its performance.

• Journal of Institute of Control, Robotics and Systems
• /
• v.8 no.2
• /
• pp.178-184
• /
• 2002

This paper deals with the transfer alignment problem of SDINS(StrapDown Inertial Navigation System) subjected to roll and pitch motions of the ship. In order to reduce alignment errors induced by ship body flexure, a linearized error model for the velocity and attitude matching transfer alignment system is first derived by linearizing the nonlinear measurement equation with respect to the dominant y axis component and defining the flexure state of random constant type. And then a robust state estimation scheme is introduced to account for modeling uncertainty of the flexure. By interpreting the simulation results and comparing with the velocity and DCM(Direction Cosine Matrix) partial matching method, it is shown that the proposed method is effective enough to improve the azimuth alignment performance.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.5
• /
• pp.405-412
• /
• 2015

This paper represents a filter design to estimate the airspeed of a spin-stabilized, trajectory-correctible artillery ammunition. Due to the limited power and space in operational point of view, the airspeed sensor is not installed, and thus the airspeed need to be estimated using limited sensor measurements. The only IMU measurements(three-axis specific forces and angular rates) are used in this application. The extended Kalman filter algorithm is applied since a linear filter can not cover the its wide operational range in airspeed and altitude. In the implementation of the EKF, the state and measurement equations are transformed into the no-roll frame for simple form of Jacobian matrix. The simulation study is conducted to evaluate the performance of the filter under various environment conditions of sensor noise and wind turbulence. In addition, the effect of the choice in filter design parameters, i.e. process error covariance matrices is analyzed on the performance of the estimation of airspeed and angular rates.

• Journal of Astronomy and Space Sciences
• /
• v.29 no.4
• /
• pp.389-395
• /
• 2012

The problem of spacecraft attitude control is solved using an adaptive neuro-fuzzy inference system (ANFIS). An ANFIS produces a control signal for one of the three axes of a spacecraft's body frame, so in total three ANFISs are constructed for 3-axis attitude control. The fuzzy inference system of the ANFIS is initialized using a subtractive clustering method. The ANFIS is trained by a hybrid learning algorithm using the data obtained from attitude control simulations using state-dependent Riccati equation controller. The training data set for each axis is composed of state errors for 3 axes (roll, pitch, and yaw) and a control signal for one of the 3 axes. The stability region of the ANFIS controller is estimated numerically based on Lyapunov stability theory using a numerical method to calculate Jacobian matrix. To measure the performance of the ANFIS controller, root mean square error and correlation factor are used as performance indicators. The performance is tested on two ANFIS controllers trained in different conditions. The test results show that the performance indicators are proper in the sense that the ANFIS controller with the larger stability region provides better performance according to the performance indicators.

• The Korean Journal of Applied Statistics
• /
• v.27 no.4
• /
• pp.523-541
• /
• 2014

We apply a Bayesian estimation procedure to the analysis of roll call voting records on 2,389 bills processed during the 18th Korean National Assembly. The analysis of roll calls yields useful tools for to combining the measurement of legislative preference with the models of legislative behavior. The current Bayesian procedure is extremely exible, applicable to any legislative setting, irrespective of the extremism of the legislator's voting history or the number of roll calls available for analysis. It can be applied to any legislative settings, providing a useful solution to many statistical problems inherent in the analysis of roll call voting records. We rst estimate the ideal points of all members of the 18th National Assembly and their condence intervals. Subsequently, using the estimated ideal points, we examine the factional disparity within each major party using the estimated ideal points. Our results clearly suggest that there exists a meaningful ideological spectrum within each party. We also show how the Bayesian procedure can easily be extended to accommodate theoretically interesting theoretical models of legislative behavior. More specically, we demonstrate how the estimated posterior probabilities can be used for identifying pivotal legislators.

• Journal of Drive and Control
• /
• v.15 no.3
• /
• pp.21-28
• /
• 2018

We propose a tension controller based on a time-delay estimation (TDE) technique for a winding machine. Firstly, we perform the necessary calculations to derive a mathematical model of the winding machine. In this sense, it is revealed that the roll radius of the winding machine is characteristically seen to be increasing or decreasing during the winding process. That being said, it is noted that the parameters of the winding machine are coupled and constantly changing during this process. Understandably then, it is noted that the model is shown to be nonlinear and time-varying. Secondly, we propose the way to apply the TDE based controller which is the so-called Time-delay Control (TDC). The TDC utilizes the time-delayed information intentionally to compensate the nonlinear and time-varying characteristics. As we have seen, the proposed controller consists of two parts: one is a TDE component, and the other is an error dynamics component which is defined by a user. In a computer simulation based on the Matlab/Simulink program, the proposed controller is compared with a conventional PID controller, which is widely used in the tension control of the winding machine. The proposed controller reduces the incidence of overshoot and steady-state error in the tension control, as compared to the conventional PID controller.