• 소성∙가공
• /
• 제17권7호
• /
• pp.491-495
• /
• 2008

Incremental forming path to manufacture a thick concave steel plate using the line array roll set is designed. To find the optimum forming path, the forming processes are simulated by the finite element method. A general-purpose commercial software, MSC MARC is used. A modeling with 8-node hexahedral elastic-plastic solid is performed to predict accurate springback and the analysis process was composed of 18 passes. The proposed forming paths are verified through experiments carried out in the prototype line array roll set. It is found that the process can be successfully applied to the fabrication of the dual curvature ship hull plate.

• International Journal of Aeronautical and Space Sciences
• /
• 제13권4호
• /
• pp.468-473
• /
• 2012

Cost is an important aspect in designing a target drone, however the poor performance of low cost IMU, GPS, and microcontrollers prevents the use of complex algorithms, such as ARS, or INS/GPS to estimate attitude angles. We propose an autopilot which uses rate gyro and GPS only for a target drone to follow a prescribed path for anti-aircraft training. The autopilot consists of an altitude hold, roll hold, and path following controller. The altitude hold controller uses vertical speed output from a GPS to improve phugoid damping. The roll hold controller feeds back yaw rate after filtering the dutch roll oscillation to estimate the roll angle. The path following controller operates as an outer loop of the altitude and roll hold controllers. A 6-DOF simulation showed that the proposed autopilot guides the target drone to follow a prescribed path well from the view point of anti-aircraft gun training.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.361-364
• /
• 2008

Incremental forming path to manufacture a thick concave steel plate using the line array roll set is designed. To find the optimum forming path, the forming processes are simulated by the finite element method. A general-purpose commercial software, MSC.MARC is used. The rolls are modeled as rigid surfaces and the thick plate is modeled as 8-node hexahedral elastic-plastic solid elements to predict accurate springback. It is found that the process can be successfully applied to the fabrication of the dual curvature ship hull plate

• Current Optics and Photonics
• /
• 제2권3호
• /
• pp.241-249
• /
• 2018

We report a midinfrared dual-field-of-view (FOV) optical system design for an airborne electro-optical targeting system. To achieve miniaturization and weight reduction of the system, it has a common aperture and fore-optics for three different spectral wavelength bands: an electro-optic (EO) band ($0.6{\sim}0.9{\mu}m$), a midinfrared (IR) band ($3.6{\sim}4.9{\mu}m$), and a designation laser wavelength ($1.064{\mu}m$). It is free to steer the line of sight by rotating the pitch and roll axes. Our design co-aligns the roll axis, and the line of sight therefore has a fixed entrance pupil position for all optical paths, unlike previously reported dual-FOV designs, which dispenses with image coregistration that is otherwise required. The fore-optics is essentially an achromatized, collimated beam reducer for all bands. Following the fore-optics, the bands are split into the dual-FOV IR path and the EO/laser path by a beam splitter. The subsequent dual-FOV IR path design consists of a zoom lens group and a relay lens group. The IR path with the fore-optics provides two stepwise FOVs ($1.50^{\circ}{\times}1.20^{\circ}$ to $5.40^{\circ}{\times}4.32^{\circ}$), due to the insertion of two Si lenses into the zoom lens group. The IR optical system is designed in such a way that the location and f-number (f/5.3) of the cold stop internally provided by the IR detector are maintained when changing the zoom. The design also satisfies several important performance requirements, including an on-axis modulation transfer function (MTF) that exceeds 10% at the Nyquist frequency of the IR detector pitch, with distortion of less than 2%.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.400-403
• /
• 2008

For the effective manufacture of doubly curved metal plates, a line array roll set (LARS) process is proposed. The suggested process utilizes a pair of upper and lower symmetric roll assemblies. In the process, the initial plate is progressed into the final shape in a stepwise or pathwise manner according to the basic principle of the incremental forming process. The deformation proceeds simultaneously in the longitudinal and transverse directions. Moreover, there is a close correlation between the deformation in the longitudinal direction and that in the transverse direction of the plates. Therefore, the finally formed shape in the incremental forming process is strongly dependent upon process conditions, such as the forming path and the forming increment. The manufacturing of arbitrary doubly curved plates with various curvatures is not an easy task because of such complicated behaviors of the plate; thus, the forming schedules for the desired shape should be carefully and accurately designed. In this study, several experiments with the LARS system were carried out for the fundamental investigation on process design for manufacturing of doubly curved plates.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.610-613
• /
• 1995

In addition to propulsive force to a flying vehicle, a rocket propulsion system can provide moments ro rotatate the flying vehicle and thus provide control of the vehicle's attitude and flight path. By controlling the direction of the thrust vectors, it is possible to control a vehicle's pitch, yaw, and roll motions. In this paper, we will introduce general thrust vector control mechanisms.

• 소성∙가공
• /
• 제20권8호
• /
• pp.611-618
• /
• 2011

Flow forming is an incremental forming process in which rollers are used to form cylindrical parts with repeated turning of both roller and starting material. Both sheet and tube can be used as the starting material. The process is highly useful for producing hollow shaped parts from a tube, with the benefit of the average strain in the final shape being significantly lower than that from a sheet material. In the present study, the flow forming process was studied and optimized for producing a hollow shaped part from seamless steel tube by both experiment and numerical analysis. Upon considering the difficulty of forming seamless steel sheet, the thickness reduction was distributed over several tool paths. In the end, an optimum process condition was attained, and the experiment verified the simulation results.

• 유공압시스템학회논문집
• /
• 제5권4호
• /
• pp.10-16
• /
• 2008

In this paper, the authors benchmark a servo valve model for the fuel supply system of Auxiliary Power Unit (APU) in the KHP helicopter. This valve is directly driven with a torque motor, and the size of small gap controlled by a flapper can make change of flow rate under given pressure drop between inlet and outlet. CFD analyses using a commercial code, ANSYS-CFX 10 are performed for the series of three-dimensional models at various openness conditions. The computational results on simplified models show that CFD can play a fine roll in the design of flow path as well as in the estimation of flow force due to its precision and good repeatability. Consequently, the CFD analysis helps valve designers to understand its flow characteristics from the basis of physical fundamentals.

• 한국정밀공학회지
• /
• 제18권2호
• /
• pp.199-205
• /
• 2001

Burr makes troubles on manufacturing process due to deburring cost, quality of products and productivity. This paper described the results of experimental study on the influence of the cutting parameters on the formation of exit burrs in face milling. Using the results of experimental study, burr types are classified and data bases are developed to predict burr formation result. From the CAD file for work geometry and the NC data for tool path, the exit angles are calculated at every edges. This program predicts the burr geometry at exit edges using the prediction algorithm and data bases which are developed experimentally. Simulation results on deformation strain and temperature are also available in specific 2-dimensional cutting conditions. Also algorithm which can determine the exit angle is proposed.