• Journal of the Optical Society of Korea
• /
• 제13권4호
• /
• pp.416-422
• /
• 2009

We have demonstrated a highly efficient cladding-pumped ytterbium-doped fiber laser, generating $>$2.1 kW of continuous-wave output power at 1.1 μm with 74% slope efficiency with respect to launched pump power. The beam quality factor ($M^2$) was better than 1.2. The maximum output power was only limited by available pump power, showing no evidence of roll-over even at the highest output power. We present data on how the beam quality depends on the fiber parameter, based on our current and past fiber laser developments. We also discuss the ultimate power-capability of our fiber in terms of thermal management, Raman nonlinear scattering, and material damage, and estimate it to 10 kW.

• Corrosion Science and Technology
• /
• 제3권4호
• /
• pp.172-177
• /
• 2004

Biaxially oriented polyethylene terephthalate copolymer(BO - PET)film laminated aluminiums have been applied for chip condenser case. The BO PET film is characterized by high molecular which gives high corrosion resistance, good adhesion and high heat resistance. The higher orientation lowers formability of the film. So, optimum orientation has to be controlled during the laminating process. And to confirm the adhesion between BO PET and aluminium and to guarantee the formability of PET laminated aluminums, we have controlled the chromium oxides weight on the aluminium and laminating condition ( laminating temperature, soaking temperature and lag time after nip roll and quenching conditions) This paper discusses the effect of the laminating conditions on the formability of laminated aluminums. As results, it is clear that the orientation of the BO PET film decreased with an increase in the strip temperature. When the film temperature is over the melting point of the film, its orientation drastically decreased.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제2권2호
• /
• pp.57-67
• /
• 2010

Experimental investigations were carried out on an Axi-symmetric Body Model fitted with Pump-jet Propulsor (PJP) in the Cavitation Tunnel at Naval Science and Technological Laboratory (NSTL). The tests were intended for evaluating the propulsion characteristics of the body and propulsor. The self propulsion point of the model for two configurations was determined after finding the corrections for tunnel blockage effects and differences in model length at zero trim. The results were found to match closely with the towing tank results. The rotor and stator torques also matched closely over full range of experiment. Further experiments were carried out on the body at $4.5^{\circ}$ angle of trim to investigate the propulsive performance and assess the operational difficulties in the sea. The results indicated an increase in resistance and decrease in rotor thrust; but the balance of torques between the rotor and stator was undisturbed, causing no concern to vehicle roll.

• International Journal of Control, Automation, and Systems
• /
• 제2권4호
• /
• pp.494-500
• /
• 2004

The wing rock phenomenon is a high angle of attack aerodynamic motion manifested by limit cycle roll oscillations. Experimental studies reveal that direct control and manipulation of leading edge vortices, through the use of 'blowing' techniques is effective in the suppression of wing rock. This paper presents the design of a robust controller for the experimental implementation of one such 'blowing' technique - recessed angle spanwise blowing (RASB), to achieve wing rock suppression over a range of operating conditions. The robust controller employs Takagi - Sugeno fuzzy system, which is fine-tuned by experimental simulations. Performance of the controller is assessed by real-time wind tunnel experiments with an 80 degree swept back delta wing. Robustness is demonstrated by the suppression of wing rock at a range of angles of attack and free stream velocities. Numerical simulation results are used to further substantiate the experimental findings.

• 한국해양공학회지
• /
• 제24권3호
• /
• pp.11-20
• /
• 2010

The purpose of this study is the investigation of the wave interaction with the rectangular floating breakwater. The flow profile obtained by PIV technique is represented to understand the vortical flow due to the wave interaction with a rectangular floating breakwater in the roll motion and the fixed condition. Also, the transmission coefficients are compared in both conditions over the extensive wave periods, which represent the performance of breakwater to attenuate the incoming waves. These results would be applied to design the floating breakwater having the mooring system to improve its performance for a certain wave period.

• Current Optics and Photonics
• /
• 제3권5호
• /
• pp.445-450
• /
• 2019

The influence of high-power laser diode (HPLD) emitter width on the device performance is investigated for 975-nm (In,Ga)(As,P)/(Al,Ga)As broad-area HPLDs, using self-consistent electro-thermal-optical simulation. To guarantee the simulation's accuracy, simulated results are matched with the measured results for a sample HPLD with fitting parameters. The influences of HPLD emitter width on temperature distribution, output power, and the beam product parameter (BPP) are analyzed for three different emitter widths of 50, 70, and $90{\mu}m$. It is found that a device with smaller emitter width exhibits both thermal rollover and thermal blooming at lower output power, but smaller BPP.

• 대한설비공학회지:설비저널
• /
• 제10권3호
• /
• pp.185-219
• /
• 1981

To analyze two dimensional incompressible laminar natural convection in a rectangular enclosure heated from below and cooled by a horizontal ceiling and two vertical walls, he primitive Navier-Stokes equations and the energy equation were solved numerically in time dependent form by a marker and cell method. A successive over-relaxation method for the elliptic portion of the problem and an explicit method for the parabolic portion were applied for the range of Grashoff number of $5{\times}10^3\;to\;5{\times}10^4$ to get the transient and steady state dimensionless temperature and velocity profiles. For the range of aspect ratio $L/H{\leqq}2.4$ in which only a pair of convection rolls exists mean Nusselt number calculated are as follows : $$N_{NU}0.89\;N_{Gr}^{0.2}(H/L)^{0.45}$$ By path lines drawn by marker particle trajectories roll number of cellular motion were observed for various aspect ratio of the enclosure.

• 한국정밀공학회지
• /
• 제9권4호
• /
• pp.13-21
• /
• 1992

Standards concerning the determination of positioning accuracy and repeatability of numerically controlled(NC) machine tools have been published relentlessly over the last 20 years. Since the publication in 1988 of the International Standard 230-2 there has been a pronounced move, both at national and international standards level, to embrace further test procedures for a complete machine tool performance assessment. For example, measurements of angular (pitch, roll, and yaw) and straightness errors along linear axes are now commonplace and complement the existing positioning accuracy and repeatablity tests. More recently the subject of circularity evalutaion has also gained considerable interest. Here dynamic tests, using a kinematic ballbar or circular masterpiece, give an instant overview of the contouring ability of the machine in two axes at specific feedrates. This information is extremely important in optimising machining accuracy. This paper describes moves to complete the machine calibration package in national and international standardis- ation for the assessment of machine tool performance.

• 전기화학회지
• /
• 제24권2호
• /
• pp.28-33
• /
• 2021

이차전지의 에너지 밀도를 높이기 위한 방법으로 전극의 로딩을 높이는 방법에 대하여 많은 시도가 이루어지고 있다. 본 연구에서는 리튬이온 이차전지용 양극에서 보편적으로 사용되어 온 기존의 polyvinylidene fluoride (PVdF) 바인더가 아닌 polytetrafluoroethylene (PTFE) 바인더를 적용하여 고로딩의 LiNi_0.5Co_0.2Mn_0.3O₂ (NCM523) 양극을 제조하였다. 기존의 슬러리 공정이 아닌 PTFE 현탁액을 이용한 반죽공정을 통하여 로딩을 높인 두꺼운 전극이 용이하게 제조되었다. PTFE 및 PVdF 기반의 전극을 5.0 mAh/cm²의 로딩레벨로 각각 제조한 결과로 PTFE를 적용한 전극이 좀 더 우수한 사이클 수명과 속도특성을 지니고 있음을 확인하였다. PTFE 바인더를 사용한 반죽공정으로 제조된 전극은 기공도가 커서 전극밀도가 높지 않기 때문에 압연을 상온이 아닌 120℃ 이상의 고온에서 진행함으로써 기공도를 낮출 수 있었으나, 이에 따른 사이클 성능의 차이는 크지 않았다. 또한, 전극조성에서 도전재의 함량을 높임으로써 고로딩 전극의 사이클 수명을 소폭 향상시킬 수 있었다. PTFE 바인더 적용으로 고로딩 전극의 성능을 향상시킬 수 있었으나, 추가적인 개선이 필요할 것이다.

• 한국방사선학회논문지
• /
• 제17권3호
• /
• pp.441-447
• /
• 2023

현재 의료방사선 분야에서 차폐를 목적으로 주로 사용되고 있는 납(Pb)소재는 방사선 차폐 기능은 뛰어 나지만 납 자체가 가지고 있는 인체 유해성과 무거운 무게에 의한 불편함 때문에 지속적으로 직, 간접적으로 방사선 피폭 위험을 차단함과 동시에 납 소재를 대체할 수 있는 인체 친화적인이며 가벼우면서 사용편의성을 가진 차폐소재의 연구는 지속적으로 진행되어지고 있다. 본 연구에서는 일반적으로 사용되는 PET(polyethylene terephthalate) 필름과 실제 방사선 방호복 사용되는 원단소재를 기재로 하여 방사선을 차폐할 수 있는 금속물질인 비스무트, 텅스텐, 주석을 스퍼터링 진공증착 방식을 통한 다층박막을 구현하여 차페필름을 제작하여 방사선 차폐소재로의 적용가능성을 평가하였다. 차폐필름을 제작하기 위한 인가전압, 롤 구동속력, 가스공급량을 제어하면서 차폐물질별 최적화된 조건을 확립하여 방사선 차폐필름 제작하였다. 모재와 차폐금속박막간 밀착력 확인은 Cross-cut 100/100으로 확인하였고 시간에 따른 박막의 변화를 측정하기 위해 내열탕 테스트 1시간을 통하여 박막의 안정성을 확인하였다. 최종적으로 구현된 차폐필름의 차폐성능은 한국방사선진흥협회를 통한 실제 방사선 차폐성능을 측정한 결과 시험조건(역넓은 빔, 관전압 50 kV, 반가층 1.828 mmAl)을 설정하여 감쇠비 16.4 (초기값 0.300 mGy/s, 측정값 0.018 mGy/s)와 감쇠비 4.31(초기값 0.300 mGy/s, 측정값 0.069 mGy/s)의 결과를 얻었다. 추후 제품화를 위한 공정효율성을 확보하여 가벼우면서 차폐성능을 보유한 필름 및 원단을 활용하여 방사선 방호복이나 차폐기능을 가진 건축자재로의 필름적용을 위한 초석을 마련하였다.