• 한국연소학회:학술대회논문집
• /
• 2006.04a
• /
• pp.75-78
• /
• 2006

Disposal of highly toxic wastes like polychlorinated biphenyls (PCBs) is very difficult. These substances create a growing mountain of problematic waste that has to be disposed properly. Conventional technologies that are based on common burning(rotary kiln, ${\sim}1100^{\circ}C$) and plasma technology(${\sim}10000^{\circ}C$) do not satisfy important conditions. for example, complete combustion of the toxic waste and the price of waste disposal. The combustor like a rocket engine is operated at relatively high pressure(${\sim}15$ bar) and relatively high temperature(>$3000^{\circ}C$) that are ideal for the complete destruction of extremely toxic substances. In this study, test compound($_o-DCB$) was dissolved in kerosine with a concentration of 10%. Pure gas oxygen was used as an oxidant. Analysis showed that the destruction efficiency achieved for ${o}-DCB$ was 99.9999% or better. The results show that a combustor based on liquid propllant rocket technology is a validated tool for the disposal of highly toxic waste, and a good alternative technology when applied to the destruction of extremely toxic wastes.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.3
• /
• pp.43-49
• /
• 2007

A ground firing test facility for Liquid Rocket Engine(LRE) combustor was built in Korea Aerospace Research Institute(KARI) in 2001 to support the development of the first Korean LRE for the KSR-III. About 170 tests were conducted up to date since its establishment and in the meantime a considerable improvements were made in the facility capability. This paper describes the outline, conducted tests and operation techniques which have been acquired through the operation of the test facility.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.6
• /
• pp.72-83
• /
• 2018

In this study, a series of CFD analyses were carried out for a hydrogen rocket combustor with a single shear coaxial injector. A hybrid RANS/LES approach was used for the turbulent combustion analysis with a two-dimensional axisymmetric configuration. Three reaction mechanisms, three spatial discretization methods, and three levels of grid resolution were compared to determine an appropriate CFD approach. The performance of the CFD prediction were investigated by comparing the wall heat flux with experimental data. Investigation of the flow field results provides an insight into the characteristics of the turbulent reacting flow of a rocket combustor with a shear coaxial injector.

• International Journal of Aeronautical and Space Sciences
• /
• v.18 no.4
• /
• pp.788-796
• /
• 2017

This paper proposes a new measurement method to improve the shortcomings of an existing integral method for measuring heat flux in plug-type heat flux gauges in the high-temperature and high-pressure environments of liquid-rocket combustors. Using the existing integral measurement method, the calculation of the surface area for the heat flux in the gauge exhibits error in relation to the actual surface area. To solve this problem, transient profiles obtained from ANSYS Fluent were used to calculate unsteady heat flux as it adjusted to the measured temperature. First, a heat flux gauge was designed and manufactured specifically for use in the high-temperature and high-pressure conditions that are similar to those of liquid rocket combustors. A calibration test was performed to prove the reliability of the manufactured gauge. Then, a combustion experiment was conducted, in which the gauge was used to measure unsteady heat flux in a liquid rocket combustor that used kerosene and liquid oxygen as propellants. Reasonable heat flux values were obtained using the gauge. Therefore, the proposed measurement method is considered to offer significant improvement over the existing integral method.

• 한국연소학회:학술대회논문집
• /
• 2000.12a
• /
• pp.92-100
• /
• 2000

One method to analyse acoustic modes is proposed to predict the characteristics of acoustic instability in liquid rocket engine. It is based on the similarity between transverse acoustic modes and adopts two-dimensional axisymmetric geometry. Using this method, the first tangential mode in the prototype combustor can be analysed through the analysis of the first radial mode in the model combustor with doubled chamber diameter. Sample numerical calculation is demonstrated applying this method to sample rocket engine and thereby acoustic instabilities of the engine are investigated. The present results show a good agreement with the previous findings. The numerical analysis based on the proposed method is cost-effective and serves as the first approximation to the true solution.

• Journal of Mechanical Science and Technology
• /
• v.18 no.7
• /
• pp.1246-1257
• /
• 2004

The objective of this paper is to characterize dynamic pressure traces measured at self-excited combustion instabilities occurring in two combustion systems of different hardware. One system is a model lean premixed gas turbine combustor and the other a fullscale bipropellant liquid rocket thrust chamber. It is commonly observed in both systems that low frequency waves at around 300㎐ are first excited at the onset of combustion instabilities and after a short duration, the instability mode becomes coupled to the resonant acoustic modes of the combustion chamber, the first longitudinal mode for the lean premixed combustor and the first tangential mode for the rocket thrust chamber. Low frequency waves seem to get excited at first since flame shows the higher heat release response on the lower frequency perturbations with the smaller phase differences between heat release and pressure fluctuations. Nonlinear time series analysis of pressure traces reveals that even stable combustion might have chaotic behavior with the positive maximum Lyapunov exponent. Also, pressure fluctuations under combustion instabilities reach a limit cycle or quasi-periodic oscillations at the very similar run conditions, which manifest that a self-excited high frequency instability has strong nonlinear characteristics.

• Journal of Mechanical Science and Technology
• /
• v.20 no.6
• /
• pp.896-904
• /
• 2006

In a liquid rocket engine, the role of gas-liquid scheme injector as an acoustic resonator or absorber is studied experimentally for combustion stability by adopting linear acoustic test. The acoustic-pressure signals or responses from the chamber are monitored by acoustic amplitude. Acoustic behavior in a rocket combustor with a single injector is investigated and the acoustic-damping effect of the injector is evaluated for cold condition by the quantitative parameter of damping factor as a function of injector length. From the experimental data, it is found that the injector can play a significant role in acoustic damping when it is tuned finely. The optimum tuning-length of the injector to maximize the damping capacity is near half of a full wavelength of the first longitudinal overtone mode traveling in the injector with the acoustic frequency intended for damping in the chamber. When the injector has large diameter, the phenomenon of the mode split is observed near the optimum injector length and thereby, the acoustic-damping effect of the tuned injectors can be degraded.

• Aerospace Engineering and Technology
• /
• v.7 no.1
• /
• pp.129-135
• /
• 2008

The 30 tonf-class liquid rocket combustor currently being developed is designed to connect the fuel feeding line at a middle position of the supersonic nozzle in order to reduce both pressure loss in the regenerative cooling passage and overall envelope of the thrust chamber in spite of increase in design complexity. To verify the design of cooling passages including fuel ring, connecting holes, two-directional cooling channels and collectors, numerical analysis has been performed.

• 한국연소학회:학술대회논문집
• /
• 2007.05a
• /
• pp.114-117
• /
• 2007

In IRR(Integral Rocket-Ramjet), the booster is integrated into the ramjet combustor. Such combustors do not contain combustor liners or flame holders within the combustor due to the limited volume and flame stabilization depends on the recirculation zones formed by the sudden expansion region between the inlet duct and the combustor. A numerical study was conducted on the effect of flame holder which could be added to the inlet duct of IRR. Two different types of flame holder installations, flame holder without sudden expansion region and flame holder with small sudden expansion region, were compared and showed different flame shapes and pressure rise in the combustor.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.10
• /
• pp.102-111
• /
• 2004

The procedure of design and manufacture of sub-scale combustor using bipropellant swirl injector with external mixing for a liquid rocket engine are described. The results of cold flow test, ignition test and combustion test of the sub-scale combustor are also given in this paper. The sub-scale combustor uses liquid oxygen(LOx) and kerosene as propellants and has a injector head, an ablative material combustor wall and a water cooled nozzle. The injector head has LOx manifold, fuel manifold, fire face plate, one center swirl injector and 18 main swirl injectors. The cold flow, ignition and combustion tests were successfully performed without damage of combustor. Results of hot firing tests show that combustion efficiency meets the target of design and operations of start and stop cyclogram are stable and high frequency combustion instability does not occur.