• 한국지반공학회논문집
• /
• 제15권3호
• /
• pp.151-160
• /
• 1999

암반 근입말뚝의 설계기준은 일반적으로 침하량 기준을 사용하므로 설계단계에서 암반근입말뚝의 하중-변위$(\sigma-\sigma)$ 거동을 잘 이해해야 하나 그 거동의 복잡성으로 인해 하중-변위 거동을 파악하기가 어렵다. 이를 위해 먼저 현장타설 콘크리트 말뚝에 대해 현장재하시험을 실시하여 그 결과로부터 암반 근입말뚝의 하중-변위 거동을 고찰하였고, 상용 프로그램인 ELAC을 이용하여 하중-변위 곡선의 형상에 큰 영향을 주는 입력변수를 변화시켜 가며 말뚝의 하중-변위 관계를 모사하였다. 최종적으로 수치해석 입력데이터와 현장 지반조사결과의 관계를 일반화함으로써 지반공학자가 설계단계에서 적절한 현장데이터를 이용하여 하중-변위 거동을 예측할 수 있도록 하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.455-465
• /
• 2008

In this study, the load distribution and deformation of rock-socketed drilled shafts subjected to axial load are investigated based on small scale model tests. In order to analyze the effects of major influencing factors of end bearing capacity, Hoek-cell triaxial tests were performed. From the test results, it was found that the initial slope of end bearing load transfer (q-w) curve was highly dependent on rock mass modulus and pile diameter, while the ultimate unit toe resistance ($q_{max}$) was influenced by rock mass modulus and the spacing of discontinuities. End bearing load transfer function of drilled shafts socketed in rock was proposed based on the Hoek-cell triaxial test results and the field loading tests which were performed on granite and gneiss in South Korea. Through the comparison with pile load tests, it is found that the load-transfer curve by the present study is in good agreement with the general trend observed by field loading tests, and thus represents a significant improvement in the prediction of load transfer of drilled shaft.

• 한국지반환경공학회 논문집
• /
• 제9권4호
• /
• pp.5-13
• /
• 2008

충전물이 암 절리면의 전단강도를 감소시키는 것과 유사하게 콘크리트와 주변 암반근입부 사이의 연약한 물질은 암반에 근입된 현장타설말뚝의 주면저항력을 감소시킨다. 이러한 현상은 콘크리트 타설 후에 암반 근입부 측벽에서 천공잔류물이나 스미어 또는 재성형 암반을 생성시키는 시공과정에서도 형성되게 된다. 콘크리트 말뚝과 주변 암반 사이의 접촉면의 특성은 시공법에 따라서 크게 영향을 받는다. 콘크리트 타설과정 또는 그 이후 형성되는 연약한 물질이 존재하거나 거칠기와 같은 콘크리트-암 접촉면의 특성은 말뚝의 주면부 거동에 큰 영향을 미친다. 본 연구에서는 유한차분법 코드를 기반으로 하는 FLAC 2D를 이용하여 스미어현상이 발생한 암반에 근입된 현장타설말뚝의 거동특성을 조사하기 위하여 변수분석을 실시하였다. 본 연구의 결과로서, 정적연직하중을 받는 암반에 근입된 현장타설말뚝의 극한주면저항력에 영향을 미치는 요소와 말뚝두부의 침하에 영향을 미치는 요소들을 확인할 수 있었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 기초기술학술발표회
• /
• pp.31-42
• /
• 2002

The Design criteria are different from one another due to the different engineering properties of rock in the every nation. Most of the test results of the rock-socketed piers were loaded two times of the design load capacities because they would be used in the foundation of the bridge or the building. So we have much difficulties in study of the load capacities of the rock-socketed piers by the test result in Korea. When we design the rock-socket piers, every designer uses the different formula, and makes different results. Recently the demand of the large bridges and the huge buildings has been increased. The adequate design criterion of the rock-socketed pier is urgently needed to design them reasonable. In this paper we analyzed the various design criteria and proposed the adequate design criterion which is based on the test results of the rock-socked piers in Korea.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.603-610
• /
• 2005

The end bearing behavior of piles socketed in weathered/soft rock is generally dependent upon the mass conditions of rock with fractures rather than the strength of intact rock. However, there are few available data and little guidance in the prediction of the end bearing capacity of drilled shafts socketed in weathered/soft rock, considering rock mass weathering. Therefore, a database of 13 load tests was constructed first, and new empirical relationships between the base reaction modulus of piles in rock and rock mass properties were developed. No correlation was found between the compressive strengths of intact rock and the base reaction modulus of weathered/soft rock. The ground investigation data regarding the rock mass conditions(e.g. Em, Eur, RMR, RQD) was found to be highly correlated with the base reaction modulus, showing the coefficients of correlation greather than 0.7 in most cases. Additionally, the applicability of existing methods for the end bearing capacity of piles in rock was verified by comparison with the field test data.

• Geomechanics and Engineering
• /
• 제18권4호
• /
• pp.363-371
• /
• 2019

In this study, the load carrying behavior of piled rafts installed in inclined bearing rock layer was investigated for rock-mounted and -socketed conditions. It was found that settlements induced for an inclined bearing rock layer are larger than for a horizontal layer condition. The load capacity of piled rafts for the rock-mounted condition decreased as rock-layer inclination angle (${\theta}$) increased, while vice versa for the rock-socketed condition. The load capacities of raft and piles both decreased with increasing ${\theta}$ for the rock-mounted condition. When bearing rock layer was inclined, loads carried by uphill-side piles were greater than those by downhill-side piles. The values of differential settlements of rock-mounted and -socketed conditions were not significantly different whereas slightly higher for the rock-socketed condition. The values of load sharing ratio (${\alpha}_p$) and its variation with settlement were not markedly changed by the inclination of bedrock. It was shown that ${\alpha}_p$ for piled rafts installed in rock layer was not affected by ${\theta}$ whereas actual loads carried by raft and piles may vary depending on the pile installation and rock-layer inclination conditions.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.57-64
• /
• 2005

Since the allowable bearing capacities of piles in weathered/fractured rock are mainly governed by settlement, the load-displacement behavior of the rock socketed pile should be well known. To predict pile head settlement at the design stage, the exact understanding of the load-transfer mechanisms is essential. Therefore, in this research, the load-transfer mechanisms of drilled shaft socketed into weathered rock was investigated. For that, 5 cast-in-place concrete piles with diameters of 1,000 mm were socketed into weathered gneiss. The static axial load tests and the load-transfer measurements were performed to examine the axial resistant behavior of the piles. A comprehensive field/laboratory testing program on weathered rock at the field test sites was also performed to describe the in situ rock mass conditions quantitatively. And then, the effect of rock mass condition on the load transfer mechanism was investigated. The side shear resistance of the pile in moderately weathered rock reached to yielding point at a few millimeter displacements, and after that, the rate of resistance increment dramatically decreased. However, that in the highly /completely weathered rock did not show the obvious yielding point, and gradually increased showing the hyperbolic pattern until with the relatively high displacement (>10 mm). The end bearing-displacement curves showed linear increase at least until with the base displacement of approximately 10 mm, regardless rock mass conditions.

• 한국지반공학회논문집
• /
• 제24권12호
• /
• pp.33-40
• /
• 2008

본 연구에서는 유한요소해석을 이용하여 암반에 근입된 현장타설말뚝의 말뚝-지반 상호작용즉, 지반의 연속성을 고려한 하중전이해석을 수행하였다. 이를 위하여 주면 하중전이함수를 사용자 정의의 경계면 모델(FRIC)로 구현하여 말뚝지반의 미끄러짐 거동과 하중전이 거동을 모델링 하였다. 본 연구결과, 주면마찰력에 의해 발생되는 선단침하량으로 대변되는 지반 연속성 영향은 주면마찰력이 극한상태로 도달할 때까지 증가함을 알 수 있었으며, 말뚝직경과 암반계수의 비(D/$E_{mass}$), 전체하중에서 주면마찰력의 비($R_s$/Q)에 영향을 받는 것으로 나타났다. 현장재하시험 사례와의 비교분석 결과, FRIC을 이용한 유한요소해석방법은 말뚝의 하중전이 거동과 말뚝-지반 상호작용 효과(coupling effect)를 적절히 나타낼 수 있었으며, 말뚝의 거동을 예측하는데 크게 개선되었음을 확인하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.431-438
• /
• 2003

The domestic design method for the shaft resistance of drilled shafts into a bedrock Is based on the empirical method, where the uniaxial compressive strength of rock specimen is utilized for calculation of the shaft resistance. This method has uncertainties in prediction of capacity of drilled shafts and result in uneconomic engineering design. Recently a new improved design method was suggested, which reflects important factors that affect the strength of pile sockets. Socket roughness is one of significant factors influencing the shaft resistance of drilled shaft socketed into rock In this paper roughness information for the shaft resistance design of socket pile was suggested on the basis of statistical analysis of data measured from wall surface In the bore holes of drilled shafts.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.526-532
• /
• 2009

말뚝의 정재하시험을 통하여 항복하중 및 극한하중을 판별하는 다양한 방법이 제안되어 왔다. 말뚝의 지지력은 주면마찰력과 선단지지력의 합으로 나타내어 왔으나 말뚝 재하시험을 통한 항복 하중 및 극한하중의 판별법은 대체로 총 침하량에 대해 판별하거나 재하하중-침하 그래프로부터 산정되는 경우가 대표적이다. 본 연구에서는 현장 대구경 양방향 재하시험 결과를 활용하여 말뚝의 주면부와 선단부로 나누어 항복하중을 판별할 수 있는 방법을 제안하고자 한다.