• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.5 no.4
• /
• pp.15-20
• /
• 1991

The paper considers a distributed adaptive control technique for industrial robots which contribute to the factory automation. The control object is to tracking for a desired trajectories under various load conditions., rapidly against load variation these control techniques divided whole system into subsystems which is controlled with the nominal and adaptation controllers, and also the asymptotic stability of these substem was proved. Simulation results shown that the proposed techniques was feasible in spite of nonlinear dynamics of robot manipulator and payload variations.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10b
• /
• pp.496-500
• /
• 1993

This paper presents an end-point position control of 1-link flexible robot arm by the PID self-tuning fuzzy algorithm. The governing equation is derived by the extended Hamilton's principle and based on the Bernoullie-Euler beam theory. The governing equation is solved by applying the Laplace transform and the numerical inversion method. The arm is mounted on the translational mechanism driven by a ballscrew whose rotation is controlled by dcservomotor. Tip position is controlled by the PID self-tuning fuzzy algorithm so that it follows a desired position. This paper shows the experimental and theoretical results of tip dispalcement, and also shows the good effects reducing the residual vibration of the end-point.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.441-444
• /
• 1988

This paper presents a methodology for developing the graphic simulator for a robotic workcell. The Petri Net model is applied to described the system state and the workcell simulation is performed by the event scheduling approach of the model. For the graphic display of simulation process, the information of the workcell resources are stored in hierachically-structured data_babe, and the geometry of the resources is described by robot modelling, component modelling, and world modelling.

• Proceedings of the KIEE Conference
• /
• 2005.07d
• /
• pp.3072-3074
• /
• 2005

In this paper, web based monitoring systems are implemented for multi-axis force control systems of an intelligence robot. A web based monitoring system is implemented by porting Linux at embedded systems which include a Xscale processor. A device driver is developed to receive data from multi-axis force sensors in Linux operation systems. To control this device driver, a socket program for the Labview is also developed.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.539-542
• /
• 1996

The forces exerted on an object by the end-effectors of multi-manipulators are decomposed into the motion-inducing force and the internal force. Motion-inducing force effects the motion of an object and internal force can't effect it. The motion of an object can't track exactly the desired motion because of internal force component, therefore internal force component must be considered. In this paper using the resolved acceleration control method and the fact that internal force lies in the null space of jacobian matrix, we construct independently the position, motion-inducing force and internal force controller. Secondly we construct the robust controller to preserve the robustness with respect to the uncertainty of manipulator parameters.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1679-1683
• /
• 2005

This paper suggests the new type of a joint torque sensor which is attached at each joint of a manipulator for making compliance. Previous six axis force/torque sensors are high cost and installed end-effector of the manipulator. However, torque on links of previous an end-effector cannot be measured. We design a joint torque sensor that can be fully integrated with an actuator in order to measure applying torque of the manipulator. The sensor system is designed through the structural analysis. The proposed joint torque sensors are installed to the 6 DOF manipulator of a mobile robot for hazardous works and we implemented experiments of measuring applied torque to the manipulator. By the experiment, we proved that the proposed low-cost joint torque sensor gives acceptable performance when we control a manipulator.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.121.1-121
• /
• 2002

Calculation unit and peripheral units that are used to make the position controller are embedded to one chip FPGA. $\textbullet$ Feed-forward PID controller and interpolator in the calculation unit mitigate frequent context switching. $\textbullet$ The peripheral units reduce the size of the joints position control board. $\textbullet$ Because the calculation unit is designed with pipeline structure, it has the advantages to apply to the multi joints.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.5
• /
• pp.1587-1600
• /
• 1991

본 연구에서는 로봇조작기를 강체부와 유연한 외팔보로 이루어진 모델로 설정 한 후 확장된 Hamilton의 원리를 적용하여 제어계의 운동방정식을 유도하였다. 계를 유한개의 제어 모드와 잔류 모드로 구분하고, 제어 모드에 대해 최적제어를 수행하기 위해 관측기를 설계하였으며, 진동에 관련된 측정 불가능한 상태변수를 추정하였다. 분석과 검토는 서보모터가 모든 제어를 담당하는 방식과 서보모터의 제어 방식에 작동 기를 추가시켜 병행 제어하는 다입출력 방식으로 구별하여 수행하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.117-122
• /
• 1992

The fuzzy-neural hybrid control system utilizing the fuzzy-neural network(FNN) will be presented in this paper. The basic structure of the controller is the parallel combination of a conventional P-controller and a FNN. Such a combination can guarantee the stability of a plant at initial stage before the rules are completely created. And a method how to automatically tunning the parameters of the FNN will be proposed with error back-propagation(BP) algorithm. Finally the effectiveness of the proposed strategy will be verified by computer simulations using a two DOF robot manipulator.

• Proceedings of the KWS Conference
• /
• 1997.10a
• /
• pp.229-233
• /
• 1997

The demand to increase productivity and quality, the shortage of skilled labour and the strict health and safety requirements have led to the development of the automated welding process to deal with many of the present problems of welded fabrication. To make effective use of the automated arc welding process, it is imperative that a mathematical model, which can be programmed easily and fed to the robot, should be developed. The objectives of the paper are to develop the mathematical equations (linear and curvilinear) for study of the relationship between process variables and bead geometry by employing a standard statistical package program, SAS and to choose the best model for automation of the $CO_2$ gas arc welding process. Mathematical models developed from experimental results can be employed to control the process variables in order to achieve the desired bead geometry based on weld quality criteria. Also these equations may prove useful and applicable for automatic control system and expert systems.