• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2003.03a
• /
• pp.377-384
• /
• 2003

Recently, there are much concerns about new and innovative transverse materials which could be used instead of conventional transverse steel in reinforced concrete bridge piers. FRP materials could be substituted for conventional transverse steel because of their sufficient strength, light weight, easy fabrication, and useful applicability to any shapes of pier sections, such as rectangular or circular sections. The objective of this research is to evaluate the seismic performance of reinforced concrete bridge pier specimens with FRP transverse reinforcement by means of the Quasi-Static test. In the first task, test columns were made using FRP rope, but these specimens appeared to fail at low displacement ductility levels due to insufficient confinement of strand extension itself. Therefore, the second task was to evaluate the seismic performance of test specimens transversely confined with FRP band. Although FRP banded specimens showed lower seismic performance than the specimen with spiral reinforcing steel, it satisfied with the response modification factor, 3, required for the single column of Korea bridge roadway design code. It was concluded that FRP band could be efficiently substituted for conventional reinforcing steel.

• Journal of Korean Port Research
• /
• v.8 no.2
• /
• pp.1-35
• /
• 1994

The main arterial which runs through the in City of Pusan, carries about 60% of downtown traffic or more, maintains about 20% yearly increase in traffic is severely suffering from the traffic congestion because of concentrated traffic volumes regardless of peak-time periods. The purpose of this study was to grasp the traffic, geometric, and signal conditions of the main arterial through the Videologging System Techniques, perform the transportation system analyses, and finally suggest the improvements which could increase the travel capacity, reduce the average delay and fuel consumption with the optimal conditions of signal system. The following conclusions were drawn : firstly the traffic system should be shifted for the travel distribution on the arterial during the peak time periods, secondly the roadway system of the arterial reviewed for left-turn traffic during the peak time periods, and thirdly the signal system of intersection reconstructed for signal optimization or progression within the range of cycle length suggested.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.2
• /
• pp.149-154
• /
• 2012

While the Earthquake Resistant Design Part of Korean Roadway Bridge Design Code provides design procedures for the No Collapse Requirement, requirements for the Serviceability Limit State are not clearly provided. The basic design method to meet the No Collapse Requirement is the spectrum analysis method using response modification factors and the Serviceability Limit State is determined by both the importance factor and the response modification factor applied in the design procedure. The importance factor can be simply applied according to the bridge importance category, however, in moderate/low seismic regions the application of the response modification factor may bring different result according to design conditions. In this study, for a typical bridge in the moderate/low seismic regions, determination procedures for the Serviceability Limit State are reviewed by carrying out earthquake resistant design and supplementary provisions for the Earthquake Resistant Design Part are identified based on the study results.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.2
• /
• pp.187-192
• /
• 2016

While structures are designed within elastic range by other designs, plastic behavior of structures should be verified and controlled in order to prevent structural collapse by the earthquake resistant design. No Collapse Requirement for typical bridges is to avoid falling down of superstructure by way of plastic behavior of certain structural elements and to operate emergency vehicles after earthquake. Such plastic behavior is restricted to connections or pier columns and appropriate measures are required for each case. Earthquake Resistant Design part of Roadway Bridge Design Code provides design processes for Ductile Collapse Mechanism by forming plastic hinges at pier columns. Also for bridges with reinforced concrete piers ductility-based design processes are provided as an appendix constructing Brittle Collapse Mechanism with connection yielding. In this study, a typical bridge with steel bearing connections and reinforced concrete piers is selected and No Collapse Design procedure considering both Ductile and Brittle Collapse Mechanism is proposed together with revisions required for the Earthquake Resistant Design part.

• International Journal of Highway Engineering
• /
• v.15 no.4
• /
• pp.177-186
• /
• 2013

PURPOSES: The purpose of this study theoretically reviews vertical grade deriving process in super high speed environment and compares overseas design criteria with Domestic Standardization also draws suitable vertical grade design criteria of high standard for Domestic Circumstances in Korea. METHODS : By researching domestic vehicle registration status, calculating typical vehicle, using Vissim which is traffic simulation program, Speed-distance curve of the vehicle is derived under each design speed condition. Through Speed-distance curve, estimating critical length of grade and considering critical length of grade, maximum longitudinal incline is proposed. RESULTS : The result of domestic vehicle registration status, the typical vehicle for deriving vertical grade is calculated based on gravity horsepower ratio 200 lb/hp. For calculating critical length of grade, according to change speed of uphill entry, speed-distance curve is derived by using Vissim. Critical length of grade is calculated based on design speed 20 km/h criteria which is point of retardation. Estimated critical length of grade is 808 m and based on this result, maximum longitudinal incline was confirmed in the design speed between 130km/h to 140km/h. CONCLUSIONS: The case of the typical vehicle(truck) which is gravity horsepower ratio 200 lb/hp, maximum longitudinal incline 2% is desirable at the super high speed environment in the design speed between 130km/h to 140km/h.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.1-13
• /
• 2010

Numerous landslides had occurred in Kangwondo in July 2006 and several restoration works had been done. A-day-accumulative rainfalls from July 12 to July 13 and July 15 to July 16 were 176mm and 202mm respectively. Disaster sites at which slope failures were studied to main causes of slope failures by investigating characteristics of rainfall, geological formation, topography and ground surface exploration around the boundary of landslides. In this study, a series of slope restoration work process is presented for reference which about the landsliding area in Han-Gye-Ryeong to O-Saek in Kwangwon-do where one of the most severe damaged area in 2006. The slope restoration work process includes site investigation, analysis on affected factor, restoration or reinforcing method design, construction procedure and recent status of that area. Also several considering points are suggested while design and construction for the reference at the other restoration works.

• Journal of the Korean Society of Safety
• /
• v.32 no.5
• /
• pp.135-140
• /
• 2017

This study deals with the safety of roundabout. The purpose of this study is to analyze the factors affecting the pedestrian accidents of roundabout near schools. In pursuing the above, this study gives particular attentions to comparatively analyzing the pedestrian accident by number of entry and circulatory lane. The traffic accident data from 2013 to 2015 are collected from TAAS data set of Road Traffic Authority. To develop the pedestrian accident model, the Poisson and negative binomial models has been utilized in this study. Such the dependent variable as the number of pedestrian accidents and the 24 independent variables as geometry, traffic volume and others are used. The main results are as follows. First, 3 Poisson and 2 negative binomial models(${\rho}^2$ of 0.153~0.426) which are all statistically significant are developed. Second, the common variable of models based on the number of circulatory roadway lane is analyzed to be the entry lane width and that of the number of entry lane is evaluated to be the design speed. Also specific variables are evaluated to splitter island, roundabout sign, number of approach road, bus stop and elementary school. Finally, the design speed might be expected to decrease the number of pedestrian accidents near schools.

• International Journal of Highway Engineering
• /
• v.4 no.1 s.11
• /
• pp.161-170
• /
• 2002

This study is a fundamental research for recycling waste polyethylene film(WPF) in asphalt concrete for roadway pavement. The objective of this study is to develop technology of making waste polyethylene asphalt mixture and evaluate properties of the asphalt concrete containing WPF. Asphalt concrete for surface course of pavement was produced through an appropriate mix-design using dense-graded and gap-graded aggregates. Marshall mix design, indirect tensile strength test, wheel tracking test and tensile fatigue test were performed. Test result showed that some WPF asphalt mixtures had a high tensile property and good resistances against rutting and fatigue cracking, compared with normal asphalt mixture.

• Journal of KIISE:Computing Practices and Letters
• /
• v.16 no.10
• /
• pp.995-999
• /
• 2010

Every year, traffic accidents and traffic congestion have been rapidly increasing, Although the roadway design and signal system have been improved to relieve traffic accidents, traffic casualties and property damage do not decrease. This paper develops a real-time traffic accident detection and analysis system (RTADAS): In the proposed system, we aim to precisely detect traffic accidents at different design and flow of intersections, However, because the data collected from intersections have uncertainty and complicated causal dependency between them, we construct probability-based networks for correct accident detection.

• Journal of Korean Society of Transportation
• /
• v.30 no.4
• /
• pp.21-32
• /
• 2012

Exclusive bus lane (EBL) is typically located in the roadway median, and is accessed by weaving across the GPLs(general purpose lanes) before entering from the left lane of the GPLs. To maximize the potential for successful EBL operations, a critical design issue that requires special attention is the length of bus weaving section before entering EBL. The process of developing guidelines for the length of bus weaving section can be supported by a sensitivity analysis of performance measure (safety) with respect to the bus weaving distance. However, field data are difficult to obtain due to inherent complexity in creating performance measure (safety) samples under various interesting flows and bus weaving distance that are keys to research success. In this paper, VISSIM simulation is applied to simulate the operation of roadway weaving areas with EBL, and based on vehicle trajectory data from microscopic traffic simulation models, the Surrogate Safety Assessment Model (SSAM) computes the number of surrogate conflicts (or degree of safety) with respect to the bus weaving distance. Then, a multiple linear regression (MLR) model using safety data (number of surrogate conflicts) is developed. Finally, guidelines for bus weaving distance are established based on the developed MLR. Developed guidelines explicitly indicate that a longer bus weaving distance is required to maintain desired safety as weaving volume increases.