• 한국연소학회:학술대회논문집
• /
• 2003.12a
• /
• pp.125-130
• /
• 2003

본 논문에서는 액체로켓엔진에서 터보펌프의 160kW급 터빈을 구동하고, 액체산소와 케로신을 추진제로 사용하는 가스발생기의 설계점 연소성능시험 결과에 대해 논의하였다. 충돌형 F-O-F 인젝터, 물냉각 채널을 가진 연소실, torch ignitor, turbulence ring 그리고 측정 링을 갖는 가스발생기에 대해 기술하였고, 점화, 연소, 종료 등의 시험 cyclogram에 대해 언급하였다. 설계점에서의 연소시험 및 turbulence ring 장착여부, 연소실 길이 변화에 따른 연소시험의 결과들에 대해 기술하였다. 연소시험 결과 가스발생기는 설계점에서 안정된 작동성을 보여주었고, 연소압력 및 온도 등의 성능이 예측치에 근접하는 결과를 보여 주었다. Turbulence ring은 출구에서의 가스온도를 균일하게 분포시켜 효과적인 혼합 장치임을 보여 주었고, 4-6msec 정도에서의 잔류시간에서는 연소효율의 차이가 크지 않음을 알 수 있었다. 가스발생기 출구에서의 온도는 공급되는 추진제의 O/F ratio에 따라 매우 민감하게 반응함을 알 수 있었다.

• International Journal of Fluid Machinery and Systems
• /
• v.8 no.1
• /
• pp.23-35
• /
• 2015

This paper presents the rotordynamic performance measurement of oil-free turbocharger (TC) supported on gas foil bearings (GFBs) for 2 liter class diesel vehicles and comparison to floating ring bearings (FRBs). Oil-free TC was designed and developed via the rotordynamic analyses using dynamic force coefficients from GFB analyses. The rotordynamics and performance of the oil-free TC was measured up to 85 krpm while being driven by a diesel vehicle engine, and compared to a commercial oil-lubricated TC supported on FRBs. The test results showed that the GFBs increased the rotor speed by ~ 20% at engine speeds of 1,500 rpm and 1,750 rpm, yielding the reduction of turbine input energy by more than 400 W. Incidentally, an external shock test on the oil-free TC casing was conducted at the rotor speed of 60 krpm, and showed a good capability of vibration damping due to the well-known dry friction mechanism of the GFBs.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.8
• /
• pp.1392-1398
• /
• 2000

In this paper, Sub Harmonic Ring Mixer using Anti-Parallel Diode Pair is studied. Conventional mixers mix LO signal with RF signal and, obtain IF signal from the difference between LO and RF. Sub harmonic ring mixers using APDP mix RF signal with the second harmonic of LO signal, LO frequency needed for conventional receiver is reduced by 1/2.The produced mixer showed 12 dB conversion loss, and 1 dB compression point of IF signal, in respect to RF signal, was found at the 0 dBm RF signal. Isolation LO/IF and LO/RF is 24.6 dB and 22.5 dB respectively. Isolation RF/LO and LO/RF is 32.6 dB and 22.5 dB respectively.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.8 no.2 s.21
• /
• pp.58-66
• /
• 2005

This paper presents miniaturized setback generators based on the conversion of mechanical energy into electrical energy for military applications, especially power supply for electronic fuzes. In order to minimize the volume of setback generators, a ring-shaped magnet enclosing a coil assembly is adopted. A mechanical safety system, shear plate, is used as a release mechanism of the setback generators to prevent the generators from operating accidentally. The setback generators are intended not to ignite an electrical detonator but to charge a capacitor which is capable of driving electronic circuit of fuze. We design the setback generators using the simulation results of an electromagnetic analysis tool, $Maxwell^{(R)}$ 2D. In experimental study, we perform safety tests of the shear plate and firing tests of the fabricated setback generators. The present setback generators show that the voltage of 14.2V is charged at the capacitor of $30{\mu}F$ within the charging time of 0.68msec and the critical acceleration for safety is 5,000G, thus verifying that the setback generators with a ring-shaped permanent magnet can be applicable to the power supply of small-caliber electronic fuze.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.2
• /
• pp.481-484
• /
• 2005

The direct conversion method is classified into the structure using the mixing technology and six-port scheme. In the view point of complexity and integration the direct conversion method using the six-port scheme is superior to that with mixing technology. Expecially, the six-port direct conversion technology provides the low power consumption and the broad-band characteristic. In this paper, the six-port direct conversion receiver with the branch-line coupler and the ring hybrid coupler is designed respectively. The performances of the designed six-port schemes are analyzed and the six-port scheme with superior performance characteristics is proposed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.211-214
• /
• 2004

The advantage of ring-shaped electrodeless fluorescent lamp is the removal of internal electrodes and heating filaments that are a light-limiting factor of conventional fluorescent lamps. Therefore, the life time of ring-shaped electrodeless fluorescent lamps is substantially higher than that of conventional fluorescent lamps and last up to 60,000 hours and is intended as a high efficacy replacement for the incandescent reflector lamp in many applications. In this paper, maxwell 3D finite element analysis program(Ansoft) was used to obtain electromagnetic properties associated with the coil and nearby structures. The electromagnetic emitting properties were presented by 3D simulation software operated at 250[kHz] and some specific conditions

• Tribology and Lubricants
• /
• v.16 no.3
• /
• pp.157-165
• /
• 2000

A discharge free Electro-Rheological Squeeze Film Damper (ER-SFD) with predetermined-clearances at leakage ends can inherently eliminate electric discharge problems while still supplying stable leakage control. Test results show that the damping force of the slotted-ring ER-SFD is mainly affected by electric voltage, oil supply pressure, position of the damper and ratio of effective surface area of slotted-rings. As the supply voltage is larger, the amplitudes of both slotted ER-SFD and rotor are decreased at first and second critical speeds. The influence of the oil supply pressure and the effective surface area ratio was shown mainly near the first critical speed. The effective surface area ratio of slotted-rings influences the reduction of flexible rotor vibration. As a result, experimental results confirm that the slotted-ring ER-SFD satisfactorily controls the flexible rotor vibration, while eliminates the inherent electric discharge problems in conventional ER-SFDs.

• Journal of electromagnetic engineering and science
• /
• v.19 no.2
• /
• pp.115-121
• /
• 2019

This paper presents the effects of the position of the split of a split-ring resonator (SRR) on the performance of a composite broadband printed dipole antenna. The antenna is made of two printed dipole arms enclosed by two rectangular and identically printed SRRs. One dipole arm and the SRR are printed on the top side of the substrate, while the other dipole arm and SRR are printed on the bottom side of the same substrate. By changing the position of the split on the SRR, different antenna characteristic values are obtained, namely, for impedance bandwidth and radiation patterns. The split position is thus a critical parameter in antenna design, because it influences the antenna's major performance immensely. Different split positions and their consequences for antenna performance are demonstrated and discussed. The antenna generates linearly polarized radiations, and it is computationally characterized for broadband characteristics. The optimized compact antenna has overall dimensions of 9.6 mm × 74.4 mm × 0.508 mm (0.06λ × 0.469λ × 0.0032λ at 1.895 GHz) with a measured fractional bandwidth of 60.31% (1.32 to 2.46 GHz for |S₁₁| <-10 dB) and a radiation efficiency of >88%.

• ETRI Journal
• /
• v.46 no.2
• /
• pp.218-226
• /
• 2024

This paper presents a novel circular fractal ring monopole antenna for ultra-wideband (UWB) hardware with dual band-notched properties. The proposed antenna consists of four crescent-shaped nested rings, a tapered feeding line at the front of the dielectric material, and a semicircular ground plane on the backside. In this design, the nested rings are used both as a radiation element and a band rejection element. The proposed antenna has a bandwidth of 9.03 GHz, which works efficiently in the range of 2.63 GHz-11.66 GHz with the dual notched bands of Worldwide Interoperability for Microwave Access (WiMAX) at 3.15 GHz-3.66 GHz and wireless local area network (WLAN) at 4.9 GHz-5.9 GHz, respectively. The antenna has a compact size of 20 mm × 30 mm × 1 mm (0.177 × 0.265 × 0.0084 λ0) and is implemented using a flame-retardant type 4 (FR4) material. It has a maximum gain of approximately 4 dB in its operating range, and experimental results support the simulation predictions with high accuracy. The findings of this study imply that the designed antenna can be utilized in UWB applications.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.8A
• /
• pp.1247-1253
• /
• 2000

To fully utilize the capabilities of a SONET/ADM network, traffic grooming is needed to multiplex a number of lower-rate traffic streams into a higher-rate stream, and vice versa. Although the capacity of a SONET ring network can be upgraded by operating it over multiple wavelengths, the corresponding network design may be costly if it employs a large number of ADMs. A cost-effective design attempts to minimize the total number of ADMs used in the network while carrying the offered traffic. We introduce and evaluate the performance characteristics of a new traffic-grooming approach for WDM ring networks, called multihop. The multihop implementation places an ADM at each node based on the requested traffic in the traffic-demand matrix then, it tries to groom the wavelengths which can be groomed. We select one of the nodes to be the "hub" node which has an ADM for each wavelength. The hub node, therefore, can "bridge" traffic between all of the wavelengths. The algorithm is specified and illustrated by a simple example. Our results demonstrate that it is beneficial to use a single-hop approach, but for a large grooming ratio and node number, we advocate the use of the multihop approach.e multihop approach.