• Korean Journal of Optics and Photonics
• /
• v.13 no.4
• /
• pp.336-339
• /
• 2002

For the improvement of the lock-in frequency of a ring laser gyro, a low-scattering mirror was employed in the laser resonator. A super-polishing technique produced fine mirror substrates of less than 1-A-rms-roughness. The mirror coating using an ionbeam sputtering technique reduced the scattering loss to less than 30 ppm. As a result of the mirror scattering enhancement of the ring laser, the lock-in frequency of the gyro was improved up to about 0.1 deg/sec.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.2
• /
• pp.109-114
• /
• 2015

A method to compensate a bias hysteresis error of the ring laser gyro using the rate of temperature is proposed in this paper. Until now, we generally have measured and compensated the error of gyro and accelerometer using the temperature. However, we utilize the measured values of the temperature dependent error elements on the temperature rate in navigation system level. We show through experiments that the proposed method can improve the navigation performance and be very effective.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.2 no.1
• /
• pp.139-149
• /
• 1999

In this paper, we estimate the scale factor error and random walk characteristics of the ring laser gyro which has the body dither for Lock-in compensation. And then, we compared those results with the static test results for 28cm square ring laser gyro which has about 0.5 deg/sec static Lock-in. In the case of sinusoidal body dither, dynamic Lock-in occurs periodically at the points where the gyro output pulse becomes the integer multiples of body dither frequency. The width of dynamic Lock-in is changed by variation of dither amplitude, and, between the width of dynamic Lock-in which occurs at the even multiple points of body dither frequency and that at the odd muliple points of body dither frequency, it has 180o phase difference. Generally random body dither is adopted to compensate for dynamic Lock-in. Then if the irregularity is not large enough, the scale factor error by dynamic Lock-in is not vanished. And if the irregularity is large enough, the scale factor error decreases, but random walk becomes larger relatively. And we confirmed that the larger body dither amplitude, the smaller random walk.

• Journal of Ocean Engineering and Technology
• /
• v.31 no.2
• /
• pp.164-169
• /
• 2017

Studies were performed on an ARS using SDINS's RLG and the geomatic sensor. To develop the ARS, experiments were performed to determine the characteristics of the RLG and geomatic sensor. Based on the results, to reduce the angular position errors of the RLG, which accumulate from the angular velocity data, an algorithm was studied that uses the Extended Kalman filter (EKF) to compensate the RLG data and geomatic sensor data. To verify the performance of the developed algorithm for reducing the cumulative angular errors, experiments that included the developed EKF were performed. Through these, it was shown that a drastic reduction in the angular errors of the RLG were achieved.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.8
• /
• pp.697-702
• /
• 2001

The ring laser gyro(RLG) has been used extensively in strapdown inertial navigation system(SDINS) because of the apparent of having wide dynamic range, digital output and high accuracy. The dithered RLG system has dynamic motion at sensor level, caused by the dithering motion to overcome the lock-in threshold. In this case, an attitude error is produced by not only the true coning of the vehicle motion but also the pseudo coning of the sensor motion. This paper describes the definition of the multi-frequency coning motion and its noncommutativity error to reject the pseudo coning error produced by the sensor motion such as the dithered RLG. The simulation results are presented to minimize the multi-frequency coning error.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1958-1961
• /
• 2004

Ring Laser Gyroscopes used as navigational sensors inherently experience a lock-in region, where very low rotational rates are not measurable. Most RLG manufacturers use a mechanical dither motor that applies a small oscillatory rotational motion larger than this region to resolve this problem. Any input acceleration that bends this dithering axis causes flexure error, which is a noncommutative error that can not be compensated by simply using integrated gyro sensor output. This paper introduces noncommutative error equations that define attitude errors caused by flexure errors. In this paper, flexure error is classified as sensor level error if the sensing axis coincides with the dithering axis and as system level error if the two axes do not coincide. The relationship between gyro output and the rotation vector is introduced and is used to define the coordinate transformation matrix and angular motion. Equations are derived for both sensor level and system level flexure error analysis. These equations show that RLG based INS attitude error caused by flexure is directly proportional to time, amount of input acceleration and the dynamic frequency of the vehicle.

• Journal of Sensor Science and Technology
• /
• v.32 no.1
• /
• pp.62-65
• /
• 2023

The wave mode calculation of a large-scale optical system in comparison to the working wavelength is practically impossible because the computational cost increases exponentially. In this paper, we propose a method that can obtain the optical mode in a large-scale optical system. The method carries out simulations by dividing the calculation area into blocks and moving along the light axis along which the light propagates. By applying this method to the calculation of resonant modes in a ring-type optical resonator, which is mainly used for ring laser optical gyro sensors, the efficiency of the proposed method was verified.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.2
• /
• pp.134-141
• /
• 2013

This paper explores a real-time system implementation to couple tightly StrapDown Inertial Navigation System(SDINS) and Global Positioning System(GPS) mounted on the aircraft. When implementing the SDINS/GPS coupled system in real-time processor, we have to deliberate SDINS's unique characteristics based on the ring laser gyro, and besides, lever-arm, measurements, and error compensation method. The novel modeling method is applied to system the misalignment error term of gyro to estimate the cumulative heading attitude errors while the aircraft banking to turn repeatedly. Captive Flight Test results show that the proposed modeling strategy has good performance.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.11
• /
• pp.921-933
• /
• 2018

There is a method to enhance the pure navigation performance of INS(Inertial Navigation System) through the rotation of inertial measurement unit to compensate error sources of inertial sensors each other and that INS using this principle of operation is called rotational INS. In this paper, the exact error analysis of rotational INS based on ring laser gyro considering the coupling effect with gravity and earth rate is performed to evaluate the navigation performance by inertial sensor error sources. And error analysis and performance evaluation result confirmed by modelling and simulation is also proposed in this paper.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.17 no.4
• /
• pp.531-536
• /
• 2014

There are trapping and stripping methods as the technique to remove the dither motion from RLG(Ring Laser Gyro) output. V/F converter output of angular sensor to measure the dither motion is used in stripping method. But bias and scale factor error is always included in V/F converter output and is a critical limiting factor for the wide application of stripping method to RLG. Therefore there have been many researches to solve this problem. The method to accurately estimate the bias and scale factor error of V/F converter using measurements of the angular sensor acquired at data sampling rate of INS is presented in this paper. To this end, stripping technique based on model of dither motion is newly applied.