• Journal of the Korean Institute of Gas
• /
• v.22 no.1
• /
• pp.60-63
• /
• 2018

This paper presents the FEM analysis results on the strength safety of a gas valve for a LPG cylinder. Based on the FEM analysis, the maximum von Mises stress on the boundary zone between a safety valve and the upper area of the thread is 99.2 MPa for the supplied gas pressure of 3.5 MPa in which the gas valve is fully opened. The maximum von Mises stress of 99.2 MPa is considered as safety value, because that value is lower than the yield stress of a brass material. In this case, the maximum deformation at the upper right part of the pressure regulator is 0.002mm. The maximum deformation zone is not a meaning part of the sealing part such as an O-ring or a diaphragm of a gas valve and a pressure regulator. The proposed hybrid gas valve model in which is integrated with a conventional cut-off valve and a pressure regulator is recommended as a gas leakage free mechanism and minimized compact size for a LPG cylinder.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.6
• /
• pp.518-521
• /
• 2019

In this paper, an active antenna module operating in the 60 GHz band is designed and fabricated by combining a commercial transmitter chip and patch array antenna. The designed module is composed of an antenna PCB and a PCB with a transmitter chip. The frequency-control and bias-control signals are applied to the transmitter chip, using an Arduino kit. A baseband I/Q signal is also applied to the chip. A ring hybrid balun converts the output of the transmitter module to a single output, which is the output of the transmitter chip that outputs a differential output. The output is delivered to the $2{\times}4$ microstrip patch array antenna PCB as a micro-computer connector. The radiation pattern of the millimeter-wave signal of the final output is compared with the simulation results. The measured radiation patterns of the fabricated active antenna module confirm that the positions of the 3 dB beam width and null point agree well with the simulation results.

• Mass Spectrometry Letters
• /
• v.13 no.3
• /
• pp.49-57
• /
• 2022

During electrospray ionization mass spectrometry (ESI-MS) analysis of proteins, the addition of supercharging agents allows for adjusting the maximal charge state, affecting the charge state distribution, and increases the number of ions reaching the detector thus, improving signal detection. We postulate that in di-substituted arene isomers, molecules with higher polarizability values should generate greater interactions and hence elicit higher signal intensities. Polarizability is an electronic parameter which has been demonstrated to predict many chemical interactions. Many properties can be predicted based on charge polarization. Molecular polarizability is a vital descriptor for explaining intermolecular interactions. We employed DFT (density functional/Hartree-Fock hybrid model, B3LYP)-derived descriptors and computed molecular polarizability for ten disubstituted arene reagents, each set made up of three (ortho, meta, para) isomers, with reported use as supercharging reagents during ESI experiments. The atomic electronic inputs were ionization potential (IP), electron affinity (EA), electronegativity (𝛘), hardness (η), chemical potential (µ), and dipole moment (D). We determined that the para isomers showed the highest polarizability values in nine of the ten sets. There was no difference between the ortho and meta isomers. Polarizability also increased with increasing complexity of the substituents on the benzene ring. Polarizability correlated positively with IP, EA, 𝛘, η, and D but correlated negatively with chemical potential. This DFT study predicts that the para isomers of di-substituted arene isomers should elicit the strongest ESI responses. An experimental comparison of the three isomers, especially of larger supercharging molecules, could be carried out to establish this premise.

• Journal of Korean Society of Forest Science
• /
• v.31 no.1
• /
• pp.8-20
• /
• 1976

For study on the variation of natural stand, three populations of Pinus densiflora S. et Z. were selected at samsanri Yongogmyun Myongjugun Kangwondo (4), Hawonri seomyun Uljingun Kyongbuk (5), and Emogdong Suweon Kyongkido (6) successibely after the selection of three population in 1974. Twenty individual trees were chosen from each population and the morphological characteristics of trees, needle and wood properties were investigated on the trees. The results are summerized as follows; 1. Serration density, resin canal number in needle did not show significant differences, however stomata row number in the both sides of needle showed highly significant differences among 3 populations. But significant differences were calculated among individual trees in a population regarding any character of needles. 2. Ail population had high correlation on the stomata row between abaxial and adaxial side of needle. 3. The Myongjungun population showed the highest value of resin duct index, which means the population had the highest degree of hybrid character. 4. The ring segment width and summerwood percentage in the wood properties had significant differences, and yet specific gravity and tracheid length had not significant differences statistically among 3 populations. But all the values were significant statistically among the ring segments within population. 5. The ring segment width decreased rapidly with increasing tree age but summerwood percentage, specific gravity, tracheid length increased slowly to the middle age of tree and then decreased slowly after the age. But the patterns of decrease or increase were some different by population. 6. The values of Uljingun population were generally high in the coefficient of variation on all the needle characters. And the values of Suweon population were always the highest and those of Myongjugun population the lowest in the coefficient of variation on all the wood properties.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.40 no.6
• /
• pp.684-696
• /
• 1995

A mutant for chalky endosperm and genetic male sterility (GMS) was newly developed in rice. The two characters were found to be controlled by single recessive gene which has pleiotropic effect, indicating that chalky seeds should be GMS seeds in segregating populations. Chalky seeds showed the same shape and size as normal seeds. However, starch composition of central part of endosperm was looser and shape of starch granules was rounder compared with normal endosperm, resulting in significantly lower grain weight, absolute density and grain hardness in chalky grains than in normal ones. Amylose content and gel consistency of chalky grains were much lower and harder, respectively. Male sterile plants showed much shorter plant height, poorer panicle exsertion and lesser panicle number compared with normal plants. Microspore abortion stage in pollen developmental process was observed as before meiosis. Male sterility of the mutant was stable regadless of temperature and day length. A system breeding hybrid rice using this mutant was discussed, comp ring with other systems utilizing cytoplasmic-genic male sterility(CGMS) and environment sensitive GMS(EGMS). Separation of GMS seeds in mixed seed bulks by specific gravity (1.14∼1.16g / cm3) was successful about 85∼90%. But some mixed normal plants were seemed to be easily removed by the apparent difference in growth characters at seedling stage. The highest natural outcrossing rate of this GMS line was as 17.3 % in a plot treated with 2-row pollinator, I-row GMS, and GA3 + cutting of flag leaf + pollen-scattering by rope.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.9
• /
• pp.896-905
• /
• 2004

In this paper, the design, fabrication and experiment on a planar array antenna with a flat-topped radiation pattern for a mobile base station antenna were described. The current distribution of an antenna aperture, which is easily realizable in a feeding network compared with the conventional one of sin(x)/x was optimized for shaping a desired flat-topped radiation pattern. The planar array antenna designed in this paper has a rectangular lattice and is composed of array elements of 16${\times}$8. Each radiating element, which is a microstrip element fed coaxially, has a linear vertical polarization and the feed network which use a Wilkinson power divider and a 180$^{\circ}$ ring hybrid coupler as a base element is designed. The flat-topped radiation pattern with 90$^{\circ}$ is shaped by 16 array elements with the element spacing of 0.55 λ$_{ο}$ in the azimuth plane, and the normal radiation pattern with 10$^{\circ}$ is shaped by 8 array elements with the element spacing of 0.65 λ$_{ο}$ in the elevation plane. Also, the planar array antenna is symmetrically divided into four parts. It consists of one hundred-twenty-eight radiating elements, thirty-two 1-4 column dividers, low 1-8 row dividers and one 1-4 input power divider. In order to verify electrical performances of the planar way antenna proposed in this paper, the experimental breadboard operated in tile band of 1.92～2.17 GHz(IMT2000 band) was fabricated, and its experimental results were a good agreement with simulation ones.

• Proceedings of the Korean Society of Toxicology Conference
• /
• 2006.11a
• /
• pp.46-54
• /
• 2006

The methylmercury (MeHg) is a toxic environmental pollutant, causing serious neurological and developmental effects in humans. Recent epidemiological studies have indicated that ingestion of MeHg in fish during pregnancy can result in neuroethological effects in the offspring. However, the mechanism underlying the MeHg-toxicity is not fully understood. To elucidate the mechanisms of toxicity of MeHg and of defense against MeHg, we searched for factors that determine the sensitivity of yeast cells to MeHg, and found that overexpression of Cdc34, a ubiquitin-conjugating enzyme (E2) that is a component of the ubiquitin-proteasome (UP) system, induces a resistance to MeHg toxicity in both yeast and human cells. The UP system is involved in the intracellular degradation of proteins. When Cdc34 is overexpressed in cells, ubiquitination reactions are activated and the degradation of certain proteins by the UP system is enhanced. Therefore, it seems likely that certain as-yet-unidentified proteins that increase MeHg toxicity might exist in cons and that toxicity might be reduced by the enhanced degradation of such proteins, mediated by the UP system, when Cdc34 is overexpressed. SCF ubiquitin-ligase is a component of UP system and consists of Skpl, the scaffold protein Cdc53, the RING-finger protein Hrt1, and one member of the family of F-box proteins. The F-box proteins directly bind to the substrates and are the determinants of substrate specificity of SCF. Therefore, we searched for the f-box protein that cofers resistance to MeHg, and found that overexpression of Hrt3 or Yi1224w induced resistance to MeHg toxicity in yeast cells. Since the protein(5) that enhance toxicity of MeHg might plausibly be induced in substrates of both f-box proteins, we next searched for substrate proteins that are recognized by Hrt3 or Y1r224w using two-hybrid screen. We found that Did3 or Crsl interacts with Hrt3; and Eno2 interacts with Yir224w. The yeast cells that overexpressed each those proteins showed hypersensitivity to MeHg, respectively, indicating that those proteins enhance the MeHg toxicity. Both Dld3 and Eno2 are proteins involved in the synthesis of pyruvate, and overexpression of both proteins might induce increase in interacellular levels of pyruvate. Deletion of Yi1006w that transports pyruvate into the mitochondria induced aresistance to MeHg. These results suggest that the promotion of the pyruvate irdlowinto the mitochondria might enhance MeHg toxicity. This study providesimportant keyfor the elucidauon of the molecular mechanism of MeHg toxicity.

• Molecules and Cells
• /
• v.37 no.11
• /
• pp.833-840
• /
• 2014

Cullin4-RING ubiquitin ligase (CRL4) is a family of multi-subunit E3 ligases. To investigate the possible involvement of CRL4 in heat stress response, we screened T-DNA insertion mutants of putative CRL4 substrate receptors that exhibited altered patterns in response to heat stress. One of the mutants exhibited heat stress tolerance and was named heat stress tolerant DWD1 (htd1). Introduction of HTD1 gene into htd1-1 led to recovery of heat sensitivity to the wild type level, confirming that the decrease of HTD1 transcripts resulted in heat tolerance. Therefore, HTD1 plays a negative role in thermotolerance in Arabidopsis. Additionally, HTD1 directly interacted with DDB1a in yeast two-hybrid assays and associated with DDB1b in vivo, supporting that it could be a part of a CRL4 complex. Various heat-inducible genes such as HSP14.7, HSP21, At2g03020 and WRKY28 were hyper-induced in htd1-1, indicating that HTD1 could function as a negative regulator for the expression of such genes and that these genes might contribute to thermotolerance of htd1-1, at least in part. HTD1 was associated with HSP90-1, a crucial regulator of thermotolerance, in vivo, even though the decrease of HTD1 did not affect the accumulation pattern of HSP90-1 in Arabidopsis. These findings indicate that a negative role of HTD1 in thermotolerance might be achieved through its association with HSP90-1, possibly by disturbing the action of HSP90-1, not by the degradation of HSP90-1. This study will serve as an important step toward understanding of the functional connection between CRL4-mediated processes and plant heat stress signaling.

• Restorative Dentistry and Endodontics
• /
• v.25 no.1
• /
• pp.123-132
• /
• 2000

To overcome problems of conventional glass ionomers, resin components have been added to glass ionomers. On a continuum between glass ionomers and composites are a variety of blends, employing different proportions of acid-base and free radical reactions to bring about cure. Popular groups defined between the ends are resin-modified glass-ionomers(RMGIs), polyacid-modified composite resins(Compomers) and ionomer modified resins. These groups show different clinical properties, and in selecting these materials for a restoration, one should sufficiently understand these different setting properties. In this study, some difference in the setting characteristics of different groups of hybrid ionomers were examined. Two RMGIs (Fuji2 LC,GC / Vitremer, 3M), three Compomers (Dyract AP, Dentsply / F2000, 3M / Elan, Kerr) were involved in this study. The identification of the setting characteristics of different groups was achieved by a two-stage study. First, thermal analysis was performed by a differential scanning calorimeter, and then the hardness of each group at different depth and time were measured by a micro-hardness tester. Thermal analysis was performed to identify the inorganic filler content and to record the heat change during setting process. The setting process was progressed for each material by chemical set mode and light-cured mode. In the hardness test, samples of materials were prepared with a 6mm-diameter metal ring, and the hardness was measured at the top, and 1mm, 2.5mm, 4mm below at just after a 40 second-cure, and after 10 minutes, 24 hours, and 7 days. Statistical analysis was performed by Mann-Whitney rank sum test to assess significant differences between set modes and types of materials, and by ANOVA and T-test to evaluate the statistical meanings of data at different times and depths of each materials. Followings are findings and conclusions derived from this study. Thermal analysis; 1. Compomers show no evidence of chemical setting while RMGIs exhibit heat output during the process of chemical setting. 2. Heat of cure of RMGIs exceed Compomers. 3. The net heat output of RMGIs through light-cured mode is higher than through chemically set mode. Hardness test; 1. Initial hardness of RMGIs immediately after light cure is relatively low, but the hardness increases as time goes by. On the contrary, Comomers do not show evident increase of the hardness following time. 2. Compomers show a marked decrease of setting degree as the depth of the material increases. In RMGIs, the setting degree at different depths does not significantly differ.

• Journal of Applied Biological Chemistry
• /
• v.61 no.1
• /
• pp.83-91
• /
• 2018

Advances in bacterial and fungal genome mining uncover a plethora of cryptic secondary metabolite biosynthetic gene clusters. Guided by the genome information, targeted transcriptional derepression could be employed to determine the product of a cryptic gene cluster and to explore its biological role. Monascus spp. are food grade filamentous fungi popular in eastern Asia and several genome data belong to them are now available. We achieved transcription activation of a cryptic fungal polyketide synthase-nonribosomal peptide synthase gene Mpfus1 in Monascus purpureus ${\Delta}MpPKS5$ by inserting Aspergillus gpdA promoter at the upstream of Mpfus1 through double crossover gene replacement. The gene cluster with Mpfus1 show a high similarity to those for the biosynthesis of conjugated polyene derivatives with 2-pyrrolidone ring and the mycotoxin fusarin is the representative member of this group. The ${\Delta}MpPKS5$ is incapable of producing azaphilone pigment, providing an excellent background to identify chromogenic and UV-absorbing compounds. Activation of Mpfus1 resulted in a yellow hue on mycelia and its methanol extract exhibit a maximum absorption at 365 nm. HPLC analysis of the organic extracts indicated the presence of a variety of yellow compounds in the extract. This implies that the product of MpFus1 is metabolically or chemically unstable. LC-MS analysis guided us to predict the MpFus1 product and to propose that the Mpfus1-containing gene cluster encode the biosynthesis of a desmethyl analogue of fusarin. This study showcases the genome mining in Monascus and the possibility to unveil new biological activities embedded in it.