• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.05a
• /
• pp.250-253
• /
• 2007

Gas Discharge Tubes (GDTs) are widely used as surge protectors for commnuication applications due to their small internal capacitance. In these days, however, they are mostly used in combined configurations, because the activation voltage required to initiate the discharge process in the GDTs for sufficient amount of time can be large enough to damage surge-sensitive protected circuits. For GDTs with a considerably high initial over-voltage value, we should limit the peak voltage using a TVS or filter. As for ZnO varistors, even though their performance for voltage restriction is excellent, their applications in high-frequency commnuication circuits have been limited because of higher internal capacitance when compared to the GDTs. In order to develop a surge protector for commnuication applications by taking advantages of these two devices, we built a combination circuit that connects a GDT and a ZnO varistor along with a choke coil in common and differential modes. We describe how the applied SPDs operate in protection process steps with the actual data obtained from the residual voltage measurements at each step. The experiment results show that the surge voltage restriction with the choke coil is more effective in 100 [kHz] RingWave voltage than in lightning impulse voltage.

• Carbon letters
• /
• v.5 no.4
• /
• pp.159-163
• /
• 2004

The polymer-ceramic hybrid, known as 'ceramer', was synthesized by a sol-gel process by incorporating different amount of alkoxide as source of silicon in resorcinol-formaldehyde in presence of basic catalyst to get different percentage of silicon in ultimate carbonized composites. FTIR of the ceramer confirms that it is a network of Si-O-Si, Si-O-$CH_2$ and Si-OH type groups linked with benzene ring. Different amount of silicon in the ceramer exhibits varying temperature of thermal stability and lower coefficient of thermal expansion as compared to pure resorcinol-formaldehyde resin. The lower value of CTE in ceramer is due to existence of silica and resorcinol -formaldehyde in co-continuous phase. Unidirectional composites prepared with ceramer matrix and high-strength carbon fibers show lower value of flexural strength at polymer stage as compared to those prepared with resorcinol-formaldehyde resin. However, after heat treatment to $1450^{\circ}C$, the ceramer matrix composites show large improvement in the mechanical properties, i.e. with 7% silicon in the ceramer, the flexural strength is enhanced by 100% and flexural modulus value by 40% as compared to that of pure resorcinol-formaldehyde resin matrix composites.

• Journal of Korean Association for Spatial Structures
• /
• v.16 no.4
• /
• pp.101-108
• /
• 2016

Lifting plan in the large spacial structure is an important factor influencing the efficiency and economy of the construction process. The purpose of this study was deriving the requirements for lifting techniques as the basic research in the double spoke wheel roof structure construction. In the lift up erection method, management plan of the interference error in the column and outer-ring was needed that occur during lifting roof structure. In the bent erection method, material usage reduction plan was required by the structural design of the temporary bent. In the hybrid erection method, lifting plan was needed that minimizes weather condition and crane usage. All lifting techniques were required Value Engineering model for reduction of cost and construction period.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.2
• /
• pp.181-190
• /
• 2008

In this paper, we suggest a new 4-port receiver instead of 6-port schematic for the demodulation of BPSK. The designed receiver is implemented by a ring-hybrid balun, two power detectors, and a comparator For the validity of the proposed receiver, we demonstrate a BPSK modulator/demodulator at 2.45 GHz. The measured data shows that the proposed 4-port receiver can successfully demodulate a data rate of 1 Mbps.

• Journal of IKEEE
• /
• v.24 no.2
• /
• pp.446-452
• /
• 2020

In this paper, we propose a energy-saving LED module using K-band microwave motion detecting sensor. To oscillate K-band microwave signal, An oscillator using a hairpin-type microstrip resonator was designed to increase stability and make fabrication easier. To radiate the microwave signal, a two-channel(TX/RX) patch antenna arrays was developed. Wilkinson power divider and ring hybrid mixer were developed and applied to obtain Doppler shift from the received signal. Shield cans were installed to protect the stability of the signals and unwanted external noise. The proposed motion detection sensor was mounted on a demonstration LED module and the energy saving performance through pre-test was verified.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.3
• /
• pp.308-315
• /
• 2002

In this paper, the 5-bit digital phase shiftier with 10 InGaAs HEMTs is designed and fabricated for U.S. mobile DBS receiving active phased array antenna system in 12 GHz band. 11.25 $^{\circ}$, 22.5$^{\circ}$ and 45$^{\circ}$ phase bits are designed in leaded-line type. 90$^{\circ}$ and 180$^{\circ}$ phase bits are designed in reflection type combined with ring hybrid. The return loss more than 17.5 ㏈, insertion louts less than 7.8 ㏈, and maximum phase error of $\pm$6$^{\circ}$for 32 phase responses are measured in 12.2 GHz~ 12.7 GHz band.

• Current Optics and Photonics
• /
• v.1 no.4
• /
• pp.372-377
• /
• 2017

We demonstrate that the local resonance of metamaterials can be tuned by the effects of organic thin films under photoexcitation. Tris (8-hydroxyquinolinato) aluminum ($Alq_3$) layers are deposited on metamaterial/silicon hybrid structures. By varying the thickness of the $Alq_3$ layer on the subwavelength scale, the resonant peak of the metamaterial becomes very adjustable, due to the effect of a thin dielectric substrate. In addition, under photoexcitation all the spectral peaks of the resonance shift to higher frequencies. This originates from the reduction of the capacitive response generated inside the gaps of split-ring resonators. The adjustability of the electromagnetic spectrum may be useful for developing optical systems requiring refractive-index engineering and active optical devices.

• Corrosion Science and Technology
• /
• v.17 no.1
• /
• pp.30-36
• /
• 2018

The high rate of corrosion of magnesium alloys makes it limited for industrial applications. Therefore, surface treatment is required to enhance their corrosion resistance. In our study, a chemical conversion coating for protecting the corrosion of the magnesium alloy, AZ31B, was prepared by using a phosphate-permanganate solution. The chemical conversion coating had a limited protection ability due to defects arising from cracks and pores in the coating layer. The sol-gel coating was prepared by using trimethoxymethylsilane (MTMS) and 3-glycidoxypropyltrimethoxysilane (GPTMS) as precursors, and aluminum acetyl acetonate as a ring opening agent. The corrosion protection properties of sol-gel and conversion coatings in 0.35wt% NaCl solution were measured by the electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization test. The EIS results indicated that the resistance of the chemical conversion coating with the sol-gel coating was significantly improved through the sol-gel sealed phosphate-permanganate conversion coating. The results of the potentiodynamic polarization test revealed that the sol-gel coating decreased the corrosion current density ($I_{corr}$). The SEM image showed that the sol-gel coating sealed conversion coating and improved corrosion protection.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.7 no.2
• /
• pp.71-77
• /
• 1982

This poper proposes the method of the balanced-mixer realization in the X-Band frequency range by the MIC coplanar magic-tee. This magic-tee is composed with microstrip and slot, as suggested by Ronde. The characteristics of balancing and isolation in this magic-tee is more preferable to those of the rat-race or hybrid ring in the wide frequency range. So, experimentally in this paper the characteristics of the MIC balanced-mixed are obtained with the VSWR less than 1, 2(in Local and Signal Arms) and the Conversion Loss, 6 dB in that frequency range, when the mixer is designed in the 3rd order (in E-arm) and 2nd order(in H-arm) Chebyshev matching networks, and with two symmetrical Schottkey Barrier Diodes.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.2
• /
• pp.22-30
• /
• 2016

It is very important to obtain the net shape of the product to maximize the shear cutting surface of fine blanking. In this paper, the fine blanking die was manufactured to achieve part characteristics, such as flatness and a fully sheared surface. The V-ring in the fine blanking die was designed to prevent lateral movement of the material. The fine blanking experiment was conducted with the fine blanking die. The material usage rate was increased by over 5.7% and that of the water-soluble lubricant was decreased by over 33% when the 2-cavity die technology was applied to fine blanking. The capacity of the existing press could lead to productivity improvement and cost reduction. Thus, 2-cavity die technology for fine blanking with a minute module of an accurate gear for producing seat recliner parts was developed.