• Magazine of the Korea Concrete Institute
• /
• v.11 no.1
• /
• pp.243-254
• /
• 1999

This paper presents a numerical study for developing the moment magnifier method that is applicable to RC flat plates subject to combined axial compressive and floor load. For the nonlinear finite element analysis, a computer program addressing material and geometric nonlinearities was developed. The flat plates to be studied are designed in accordance with the Direct Design Method in Korean Building Code for Structural Concrete. This paper proposes the buckling force and the moment magnification factor for the flat plate under the governing load condition that is the combined vertical and subsequently applied uniaxial compressive load. The buckling force is defined with two ingredients: the buckling coefficient and the effective flexural rigidity. Parametric studies are performed to investigate variations of the buckling coefficient and the effective flexural rigidity. Based on the numerical results, this paper provides the design values of the buckling coefficient and the effective flexural rigidity, and the design procedure for the moment magnifier method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.8
• /
• pp.905-910
• /
• 2014

The steel grating discussed in this study is a drain cover that enhances the rigidity of the steel frame using an inclined inflow tract for wastewater, facilitates smooth drainage, and prevents the escape of bad smell from the drain. Recently, the urban problem of bad smell in sewerage lines has been hindering the improvement of living standards. Moreover, the frequent failure of existing products deters bad smell prevention measures and results in administrative power and budget wastage. The pressure to reduce budgets propels the increased demand for functional steel grating. Thus, this study focused on optimizing the design parameters of a steel grating by simultaneously considering its rigidity and drainage efficiency.

• Polymer(Korea)
• /
• v.35 no.5
• /
• pp.385-389
• /
• 2011

In rubbing process, process factors, the properties of alignment layer and the physical properties of rubbing cloth have acted as important variables. These factors affect the orientation properties of the alignment layer by rubbed extent that is determined by rubbing density and rubbing force. In this work, we studied the effects of rubbing cloths with different pile density and rigidity on rubbing density(length) and rubbing force. As the pile density and rigidity of rubbing cloths increased, the birefringence and the surface roughness of the rubbed alignment layers became bigger, but the characteristics of rubbing-effect had differed each other. The pile density of rubbing cloths which was related with the number of pile, affected the rubbing density(length). On the other hand, the pile rigidity of rubbing was closely related to rubbing force rather than the rubbing density(length).

• Korean Journal of Materials Research
• /
• v.7 no.12
• /
• pp.1089-1096
• /
• 1997

본 연구에서는 에폭시/산무수물계에 화학양론비(r=산무수물/에폭시)를 0.5, 0.7,0.9,1.1로 변화시켜 서로 다른 두종류의 경화촉진제 1-cyanoethy1-2-ethy1-4-methy1 imidazole(2E4MZ-CN)과 N,N-dimethy1 benzy1 amine(BDMZ)을 첨가한 시료에 대한 경화거동과 경화 후 물성을 관찰하였다. 이 시료의 등온 경화거동은 동역학 측정기(dynamic mechanical analyzer, DMA)와 시차주사 열량분석기(differential scanning calorimeter, DSC)를 이용하여 조사하였다. DMA로부터 구해진 결과를 보면 경화시 상대저장강성을 (relative storage rigidity, RSR)과 상대손실강성율(relative loss rigidity, RSR)과 상대손실강성율(relative loss rigidity, RLR)의 변화가 r값과 경화촉진제의 종류에 영향을 받았다. 그리고 DSC결과는 r값이 감소함에 따라 경화가 촉진되는 것으로 나타났다. 경화물의 성질을 조사하기 위하여 사용된 DMA로부터 얻어진 유리전이온도(glass transition temperature, T$_{g}$)와 가교결합간의 평균분자량(average molecular weigh between crosslinks, M$_{c}$은 사용한 두 경화촉진제에 대하여 r값의 영향이 다르게 나타났다. BDMA의 경우는 T$_{g}$가 1:1화학양론비인 r=0.9에서 최고치를 보였으나, 2E4MZ-CN은 r이 감소함에 따라 계속 증가하는 양상을 보였다. 이와 같은 경향은 2E4MZ-CN을 경화촉진제로 사용하였을 때 에폭시가 과량으로 될수록 잔류 에폭시기들간의 에케르반응이 추가적으로 일어나 M$_{c}$가 감소하기 때문이다.

• Journal of Korean Neurosurgical Society
• /
• v.37 no.5
• /
• pp.364-369
• /
• 2005

Objective: Spinal instrumentation without fusion often fails due to biological failure of intervertebral joints (spontaneous fusion, degeneration, etc). The purpose of this study is to investigate the influence of fixation rigidity on viability of intervertebral joints. Methods: Twenty pigs in growing period were subjected to posterior segmental fixation. Twelve were fixed with a rigid fixation system(RF) while eight were fixed with a flexible unconstrained implant(FF). At the time of the surgery, a scoliosis was created to monitor fixation adequacy. The pigs were subjected to periodic radiological examinations and 12pigs (six in RF, six in FF) were euthanized at 12-18months postoperatively for analysis. Results: The initial scoliotic curve was reduced from $31{\pm}5^{\circ}$ to $27{\pm}8^{\circ}$ in RF group (p=0.37) and from $19{\pm}4^{\circ}$ to $17{\pm}5^{\circ}$ in FF group (p=0.21). Although severe disc degeneration and spontaneous fusion of facet joints were observed in RF group, disc heights of FF group were well maintained without major signs of degeneration. Conclusion: The viability of the intervertebral joints depends on motion spinal fixation. Systems allowing intervertebral micromotion may preserve the viability of intervertebral discs and the facet joint articular cartilages while maintaining a reasonably stable fixation.

• Structural Engineering and Mechanics
• /
• v.86 no.4
• /
• pp.461-472
• /
• 2023

This paper proposes a novel method for increasing the distortional frame rigidity of off-rail box girder bridges for cranes by reinforcing the diaphragm with staggered truss. The study starts by using the Matrix Displacement Method to determine the shear angle of the staggered truss diaphragm under two assumptions: hinge joint and rigid joint. To obtain closed-form solutions for the transversal and longitudinal deformations and warping stress of the crane girder, the study employs the Initial Parameter Method and considers the compatibility of shear deformation at joints between the diaphragms and the girder. The theoretical solutions are validated through finite element analysis, which also confirms that the hinge-joint assumption accurately represents the shear angle of the staggered truss diaphragm in girder distortion. Additionally, the study conducts extensive parameter analyses to examine the impact of staggered truss dimensions on distortional stress and deformation. Furthermore, the study compares the distortional warping stresses of crane girders reinforced with staggered truss diaphragms and those reinforced with perforated ones, emphasizing the importance of incorporating stagger truss in diaphragms. Overall, this paper provides a thorough evaluation of the proposed approach's effectiveness in enhancing the distortional frame rigidity of off-rail box girder bridges for cranes. The findings offer valuable insights into the design and reinforcement of diaphragms using staggered truss to enhance the structural performance of crane girders.

• Steel and Composite Structures
• /
• v.17 no.4
• /
• pp.535-548
• /
• 2014

In this paper, the exact closed-form solutions for torsional analysis of heterogeneous magnetostrictive circular cylinder are derived. The cylinder is subjected to the action of a magnetic field produced by a constant longitudinal current density. It is also acted upon by a particular kind of shearing stress at its upper base. The rigidity of the cylinder is graded through its axial direction from one material at the lower base to another material at the upper base. The distributions of circumferential displacement and shear stresses are presented through the radial and axial directions of the cylinder. The influence of the magnetostrictive parameter is discussed. The effects of additional parameters are investigated.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.25-32
• /
• 2000

In order to analyze the behavior of piled abutment adjacent to surcharge loads a numerical study was conducted. In 2D plane stalin analysis, the distribution of lateral soil movement was investigated by varying the thickness of clay layer and the magnitude of surcharge loads. In 3D analysis, the magnitude and distribution of lateral pile-soil movement were studied for different cap rigidity. Based on limited parametric studies, a simple method is proposed to identify the lateral pressure of piled abutment adjacent to surcharge loads.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 1999.10c
• /
• pp.258-264
• /
• 1999

In this study, a computer program was developed for analysis of the orthotropic curved ring sector plates. In the developing program , the thin-plate theory and multi-base coordinate system was adopted. The effect of design factors-boundary conditions, loading conditions, steel ratio, open angle, radius of curvature and relative flexural rigidity between slab and edge-beam-on the behavior of the circular ring sector plates were discussed. Also, the practical limitations was proposed to replace the problem of the orthotropic sector plate by equivalent rectangular plage.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04a
• /
• pp.585-590
• /
• 1995

This paper describes strain distribution analysis of a multiple parallel plate structure for a multi-componenet force and moment sensor. A parallel plate structure which has higher rigidity than a simple beam structure are widely used for multi-component force and moment sensor. The strain distribution in the beams of a parallel plate structure should be accurately calculated to design a high precision multi-component force and moment sensor. We derived equations to calculate the strains for multiple parallel plate structure. It reveals that results from finite element analysis and experiment are in good agreement with results from the derived equations.