• Journal of Ocean Engineering and Technology
• /
• v.7 no.2
• /
• pp.162-172
• /
• 1993

In the present paper, the overall state of the arts of ice mechanics which is the most typical research topic of the artic engineering field was studied. And also, ice loads genrated by ice-structure interaction were estimated using numerical approach. The effects of viscous property of ice sheets to the ice load were investigated. The time dependent deformation behaviors of ice was modeled by visco-plastic problem using the finite element formalism. Constitutive model representing the material properties of ice was idealized by comblned rheological model with Maxwell and Voigt models. Numerical calculations for the bending and crushing behavior of ice sheet which are the most typical interaction modes between ice sheets and structures were carried out. The time dependent viscous behaviors of ice sheets interaction forces acting on structures were analyzed and the results were studied in detail.

• Korea-Australia Rheology Journal
• /
• v.18 no.3
• /
• pp.133-141
• /
• 2006

Carbon dioxide was absorbed into the aqueous nanometer sized colloidal silica solution of 0-31 wt% and 2-amino-2-methyl-1-propanol of $0-2kmol/m^3$ in a flat-stirred vessel with the impeller of various sizes and speeds at $25^{\circ}C$ and 0.101 MPa to measure the absorption rate of $CO_2$. The volumetric liquid-side mass transfer coefficient$(k_La)\;of\;CO_2$ was used to obtain the empirical correlation formula containing the rheological behavior of the aqueous colloidal silica solution. Reduction of the measured $k_La$ was explained by the viscoelastic properties of the aqueous colloidal silica solution. The theoretical value of the absorption rate of $CO_2$ was estimated from the model based on the film theory accompanied by chemical reaction and compared with the measured value.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.327.1-327
• /
• 2002

MR(Magnetorheogical) fluid composed of fine iron powders dispersed in silicon oil is utilized to many smart structures and devices because of its significant rheological property change by the application of an external magnetic field. When we deal with the shock wave attenuation of warship structures, we should be able to characterize the high frequency behavior of MR fluids. So far, however, much efforts have been focused on the material characterization of MR fluids at low frequencies below 100㎐. (omitted)

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.6
• /
• pp.27-36
• /
• 2003

The Electro-Rheological (ER) fluid has been used to the ultraprecision polishing of single crystal silicon as new polishing slurry whose properties such as yield stress and particle structure changed with the application of an electric field. In this work, it is aimed to find the effective parameters in the ER fluid on material removal in the polishing system whose structure is similar to that of the simple hydrodynamic bearing. The generated pressure in the gap between a moving wall and a workpiece, as well as the electric field-induced stress of the mixture of ER fluid-abrasives, is evaluated experimentally, and their influence on the polishing of single crystal silicon is analyzed. Moreover, the behavior of abrasive and ER particles is described.

• Geotechnical Engineering
• /
• v.13 no.5
• /
• pp.133-144
• /
• 1997

It was proved from the viscosity test for deposits of debris flows(Kim and Seo, 1997) that the property of debris flows could be represented as Bingham plastic model. Based on this bahavior, numerical analysis for the movement of debris flows is carried out by using a computer progran Polyflow which huts been developed for the analysis of the behavior of non-Newtonian fluid. The numerical results obtained from two sites agree well with the movement predicted by an empirical formula. It can be concluded, therefore. that this scheme can be used for the analysis of the movement of debris flow.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.5
• /
• pp.450-455
• /
• 2007

LCD color filters have been manufactured in a process called photolithography to date, but various printing methods have been studied currently in response to the trend of low-end LCD panels. Direct Printing Process is a suitable fabrication technique to develope pigment components whose dimensions are in nano. The success of this process depends on the systematic preparation of pigment millbase. Conventional millbase dispersions are constituted of the organic pigments, monomer, dispersant and solvents. An experimental study on the rheology of millbase dispersions is presented. Subsequently, this thesis attempts to find out the dispersive characteristics as well as the selection of pigments, monomers and dispersants in the part of millbase among the stages of manufacturing LCD color filters using the direct printing methods. The dispersive characteristics were shown through analytic devices such as PSA, Rheometer, etc.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.431-432
• /
• 2006

In this study, the effect of the temperature of magnesium slurry was investigated by mechanical stirring method. The evaluations of rheological behavior of AM50A magnesium alloy were measuring of viscosity and microstructures in the semisolid state. The apparent viscosity was investigated at continuous cooling rate using a concentric cylinder viscometer. Measurement of viscosity measures torque that act to stirrer rotating in slurry doing continuous cooling using torque-meter and expressed by POWER-LAW. Microstructures were observed after mechanical stirring that enforce time at steady state temperature of solid fraction.

• Macromolecular Research
• /
• v.9 no.3
• /
• pp.164-170
• /
• 2001

Recently in order to describe the complex rheological behavior of polymer melts with long side branches like low density polyethylene, new constitutive equations called the pom-pom equations have been derived by McLeish and Larson on the basis of the reptation dynamics with simplified branch structure taken into account. In this study mathematical stability analysis under short and high frequency wave disturbances has been performed for the simplified differential version of these constitutive equations. It is proved that they are globally Hadamard stable except for the case of maximum constant backbone stretch (λ = q) with arm withdrawal s$\_$c/ neglected, as long as the orientation tensor remains positive definite or the smooth strain history in the now is previously given. However this model is dissipative unstable, since the steady shear How curves exhibit non-monotonic dependence on shear rate. This type of instability corresponds to the nonlinear instability in simple shear flow under finite amplitude disturbances. Additionally in the flow regime of creep shear flow where the applied constant shear stress exceeds the maximum achievable value in the steady now curves, the constitutive equations will possibly violate the positive definiteness of the orientation tensor and thus become Hadamard unstable.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.24 no.2
• /
• pp.11-24
• /
• 2006

The Lithographic ink is composed of pigment, vehicle and additives. In especially, the vehicle is the most important element and consist of vegetable oils, mineral oils and resins. Varnishes have to resist certain forms of chemical and physical attack during ink manufacturing process and printing process So this varnish cooking is very important. In this paper, effects of cooking conditions of varnish using phenolic modified rosin ester on physical properties of the vehicle were studied. The varnish cooked according to temperature and time were compared in order of average molecular weight by the GPC method. and the rheological properties were found by rotational rheometer. And the emulsion behavior were compared by high speed emulsification tester which were set on 1200 rpm and $40^{\circ}C$ temperature (Novomatics Lithotronic). We displayed viscosity against tack(Inkometer Thwing-Albert M-106) by diagram.

• Journal of the Korean Ceramic Society
• /
• v.54 no.6
• /
• pp.470-477
• /
• 2017

Ceramic processing to fabricate 3D complex ceramic structures is crucial for structural, energy, environmental, and biomedical applications. A unique process is ceramic stereolithography, which builds ceramic green objects from CAD files from many thin liquid layers of powder in monomer, which are solidified by polymerization with a UV laser, thereby "writing" the design for each slice. This approach directly writes layers in liquid ceramic suspension and allows one to fabricate ceramic parts and products having more accurate, complex geometries and smooth surfaces. In this paper, both UV curable materials and processes are presented. We focus on the basic material principles associated with free radical polymerization and rheological behavior, cure depth and broadening of cured lines, scattering at ceramic interface and their corresponding simulation. The immediate potentials for ceramic AM to change industry fabrication are also highlighted.