• 한국세라믹학회지
• /
• 제44권8호
• /
• pp.430-436
• /
• 2007

Rheological properties of cement paste containing ultrafine blastfurnace slag (UBS, $9600cm^2/g$) were investigated by mini-slump test, pH meter, conduction calorimeter and coaxial cylinder viscometer. In order to improve rheological properties of the cement paste, granulated blastfurnace slag (GBS, $3500cm^2/g$) and polycarboxylate type superplasticizer (PC) were also used in this experiment. The fluidity of cement paste containing UBS was decreased. The yield stress and plastic viscosity of cement paste was increased with increasing UBS. But the rheological properties were improved when GBS and PC were added to UBS blended cement paste. In the relationship between the yield stress and the plastic viscosity or the mini-slump value, the yield stress of the cement paste was proportional to the plastic viscosity of it. However the cement paste mini-slump value was in inverse proportional to the yield stress.

• Advances in concrete construction
• /
• 제6권5호
• /
• pp.465-483
• /
• 2018

The most crucial factor determining the pumping performance of concrete is the characteristics of the lubricating layer formed between the pipe wall and the inner concrete. Thus, it is important to accurately identify the rheological properties of the lubricating layer to predict the pumping of concrete. In this study, a new method is proposed for measuring the rheological properties of the lubricating layer with improved convenience. To verify the new method, a pumping test was conducted with 337 m-long horizontal piping. The rheological properties of the lubricating layer were assessed by a previously verified method and the new method proposed in this study for a total of four concrete mixtures with design strength ranging from 27 MPa to 60 MPa. The correlation between the existing method and the new method in relation to the viscosity of the lubricating layer was determined, and it was possible to predict the pumping performance with an accuracy of about 88.5% using the viscosity of the lubricating layer obtained from this correlation.

• Food Science and Biotechnology
• /
• 제15권4호
• /
• pp.589-594
• /
• 2006

The effect of five commercial gums (carboxylmethylcellulose, CMC; guar gum, GG; hydroxypropylmethyl-cellulose, HPMC; locust bean gum, LBG; and xanthan gum) at a concentration of 0.25% on the rheological properties of rice flour (RF) dispersions was investigated in steady and dynamic shear. The steady shear rheological properties showed that RF gum mixture dispersions (5%, w/w) at $25^{\circ}C$ had high shear-thinning flow behavior (n=0.20-0.31) exhibiting a yield stress. Magnitudes of consistency index (K), apparent viscosity (${\eta}_{a,100}$), and Casson yield stress (${\sigma}_{oc}$) of RF-gum mixtures were much higher than those of RF dispersion with no added gum (control). Activation energy values (6.67-10.8 kJ/mole) of RF-gum mixtures within the temperature range of $25-70^{\circ}C$ were lower than that (11.9 kJ/mole) of the control. Dynamic rheological data of log (G', G") versus log frequency (${\omega}$) of RF-gum mixtures had positive slopes (0.15-0.37) with G' greater than G" over most of the frequency range (0.63-63 rad/sec), demonstrating a frequency dependency. Tan ${\delta}$ (G"/G') values of RF-gum mixtures, except for xanthan gum, were much higher than that of the control.

• KCI Concrete Journal
• /
• 제13권1호
• /
• pp.35-41
• /
• 2001

This paper investigated rheological properties of binder pastes for self-compacting high performance concrete. Six mixtures of self-compacting concrete were initially prepared and tested to estimate self-compacting property. Then, the binder pastes used in self-compacting concrete were tested for rheological properties using a rotary type rheometer. Binder pastes with different water-binder ratios arid flow values were also examined to evaluate their rheological characteristics. The binders were composed of ordinary Portland cement, fly ash, two types of pulverized blast-furnace slag, and limestone powder. The flow curves of binder pastes were obtained by a rotary type rheometer with shear rate control. Slump flow, O-funnel time, box, and L-flow teats were carried out to estimate self-compacting property of concrete. The flow curves of binder pastes for self-compacting concrete had negligible yield stresses and showed an approximately linear behavior at higher shear rates beyond a certain limit. Test results also indicated that the binders incorporating fly ash are more appropriate than the other types of binders in quality control of self-compacting concrete.

• Elastomers and Composites
• /
• 제53권2호
• /
• pp.67-74
• /
• 2018

Magneto-rheological elastomers (MREs) are smart materials in which the inherent stiffness and damping properties can be changed by the influence of an external magnetic field. The magneto-rheological (MR) effect depends on the orientation characteristics of the dispersed magneto-responsible particles (MRPs) in the matrix. In this study, natural rubber (NR) and ethylene propylene diene rubber (EPDM) were blended and used as a matrix of an MRE. EPDM was pre-cured before blending with NR. The Mooney viscosity, curing characteristics, and mechanical properties were analyzed with various pre-curing conditions of EPDM and the NR/EPDM blend. The results show that excellent mechanical properties of the NR/EPDM blend-based MRE were obtained when the pre-curing time of EPDM was 60 min. The aging property of the NR-based MRE was improved by the introduction of pre-cured EPDM. Also, the anisotropic MRE showed a higher MR effect than that of the isotropic MRE.

• 대한화장품학회지
• /
• 제25권4호
• /
• pp.123-131
• /
• 1999

Liquid crystal known as a rheological barrier to coalescence of oil droplets, increases emulsion stability, water-holding capacity and promotes active material penetration to skin. Some investigation for its rheological characteristics have been reported but its relations to consumer perception have been rarely published. In this study, oil/water emulsion and oil/liquid crystal/water systems were manufactured using the same composition or Behenyltrimethylammonium chloride/Cetostearyl alcohol/Lanolin oil. and rheological properties or each system were investigated with Cone and Plate rheometer. The formation of liquid crystalline phase was observed with polarized microscope and Differential Scanning Calorimeter. Continuous shear experiment, creep, yield and water holding capacity were measured for oil/water and oil/liquid crystal/water systems. The results were compared with sensory evaluations. Oil/liquid crystal/water system showed higher,viscosity at the same shear rate. higher viscoelasticity and higher yield stress than oil/water system. These properties were expected to show good spreadability and excellent richness without waxiness in hair can: products of creme type. This expectation was consistent with the results of sensory experiments. Water-holding capacity was evaluated by measuring residual water of specimens at specific temperature and relative humidity. Oil/liquid crystal/water system was proved to have higher ability to hold water in comparison with oil/water system. The results indicated that oil/liquid crystal/water system was of benefit to rheological properties creme type hair care products.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(II)
• /
• pp.313-316
• /
• 2005

In the recent design of high ductile fiber-reinforced cementitious composite ECC, which exhibits tensile strain-hardening behavior in the hardened state, optimizing both processing mechanical properties for specific applications is critical. This study introduced a method to develop useful ECCs in field, which possess the different fluid properties to facilitate diverse types of processing (i.e., self-consolidating or spray processing). Control of rheological modulation was regarded as a key factor to allow the performance of the desired processing, while retaining the ductile material properties. To control the rheological properties of the composite, we first determined basic ECC compositon, which is based on micromechanics and steady-state cracking theory. The stability and consequent viscosity of suspensions were, then, mediated by optimizing dosages of chemical and mineral admixtures. The rheological properties altered by this approach were revealed to be effective in obtaining ECC hardened properties, allowing us to readily achieve the desired function of the fresh ECC.

• Advances in concrete construction
• /
• 제6권6호
• /
• pp.561-583
• /
• 2018

A variety of polycarboxylate ether (PCE)-based superplasticizers are commercially available. Their influence on the rheological retention and slump loss in respect of concrete differ considerably. Fluidity and slump loss are the cardinal features responsible for the quality of concrete. These are related to the dispersion of cement particles and the hydration process which are greatly influenced by type of polycarboxylate ether (PCE)-based superplasticizers. On the backdrop of relatively less studies in the context of rheological retention of high strength self-consolidating concrete (HS-SCC), the experimental investigations were carried out aiming at quantifying the effect of the six different PCE polymers (PCE 1-6) on the rheological retention of HS-SCC mixes containing two types of Ordinary Portland Cements (OPC) and unwashed crushed sand as the fine aggregate. The tests that were carried out included $T_{500}$, V-Funnel, yield stress and viscosity retention tests. The supplementary cementitious materials such as fly ash (FA) and micro-silica (MS) were also used in ternary blend keeping the mix paste volume and flow of concrete constant. Low water to binder ratio was used. The results reveal that not only the PCEs of different polymer groups behave differently, but even the PCEs of same polymer groups also behave differently. The study also indicates that the HS-SCC mixes containing PCE 6 and PCE 5 performed better as compared to the mixes containing PCE 1, PCE 2, PCE 3 and PCE 4 in respect of all the rheological tests. The PCE 6 is a new class of chemical admixtures known as Polyaryl Ether (PAE) developed by BASF to provide better rheological properties in even in HS-SCC mixes at low water to binder mix. In the present study, the PCE 6, is found to help not only in reduction in the plastic viscosity and yield stress, but also provide good rheological retention over the period of 180 minutes. Further, the early compressive strength properties (one day compressive strength) highly depend on the type of PCE polymer. The side chain length of PCE polymer and the fineness of the cement considerably affect the early strength gain.

• Food Science and Biotechnology
• /
• 제15권5호
• /
• pp.756-762
• /
• 2006

Freeze concentration of milk was carried out through the controlled recrystallization of ice in a multi-stage freeze concentrator. Rheological characteristics of ice slurries were analyzed to determine efficient concentration levels for the freeze concentration process. It was determined that efficient concentration level was 17% of total solids in the first and 27% in the second stage. Physicochemical properties were compared between freeze concentrated and evaporated milk. Freeze concentrated milk was more similar in color appearance to control milk than was evaporated milk. pH significantly decreased in evaporated milk than in freeze concentrated milk. pH of freeze concentrated milk resulted in similar value to control. These results indicated the advantages of freeze concentration as a non-thermal milk processing technology in terms of physicochemical properties. Consequently, we investigated the influence of ice recrystallization on the rheological characteristics of ice slurries and physicochemical properties of freeze concentrated milk.

• 폴리머
• /
• 제32권1호
• /
• pp.19-25
• /
• 2008

본 논문은 실리카복합재료인 치약제의 결합제 역할을 하는 수용성 폴리머인 carboxymethylcellulose (CMC)와 carbomer, Mg/Al silicate의 최적의 조성 비율을 구하여 치약제의 레올로지 속성을 개선하는 데에 목적이 있다. 실험계획법 중 혼합물 반응표면분석법을 적용하여 응력, 겔 강도, 늘어짐, 탄성에 대해 oscillatory 레오미터로 측정하였다. 실험 결과 CMC와 carbomer는 치약제의 겔 강도와 응력에 많은 영향을 미치고, CMC는 치약제의 늘어짐을 초래하며, CMC와 Mg/Al silicate가 탄성에 도움이 된다는 사실을 규명하였다. 반응치 최적화를 통해 최적의 폴리머 및 silicate 조성비를 구하여 실험한 결과 개선된 레올로지 속성의 치약제를 확인할 수 있었다.