• Applied Chemistry for Engineering
• /
• v.8 no.2
• /
• pp.276-285
• /
• 1997

The theoretical and experimental analysis on polyamide used for reverse osmosis thin-film composite membrane had been conducted. The physicochemical properties of polyamide had been varied by preparation recipes which depends on kinds of monomer, solvents and polymerization time. These properties and performance as a reverse osmosis membrane had been calculated by group contribution method. The experimental results has the same trends with theoretical preview.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.2
• /
• pp.383-393
• /
• 1996

This paper considers the evaluation of the ecquistion performance for an accesschannel preamble based on a random access procedure of direct sequence code division multiple access(DS/CDMA) reverse link. The parallel acquistion technique that employs the single-well detection scheme and the multiple-dwell(double-dwell) detection scheme is mentioned. The acquisition performance for two detection schemes is compared in therms of the acquisition probability and the acquisition time. The parallel acquisition is done by a bank of N parallel I/Q noncoherent correlators. Expressions on the detection, false alarm, and miss probabilities of the single-dwell and multiple-dwell(double-well) detection schemes are derived for multiple H$_{1}$ cells and multipath Rayleight fading channel. comparing the single-dwell detection scheme with the multiple-dwell(double-dwell) detection scheme in the case of employing the parallel acquisition technique in the reverse link,the numerical results show that the single-dwell detection scheme deomonstrates a better performance.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.3C no.1
• /
• pp.28-32
• /
• 2003

In this paper, we have studied the in-situ end point detection (EPD) for direct chemical mechanical polishing (CMP) of shallow trench isolation (STI) structures without the reverse moat etch process. In this case, we applied a high selectivity $1n (HSS) that improves the silicon oxide removal rate and maximizes oxide to nitride selectivity Quite reproducible EPD results were obtained, and the wafer-to-wafer thickness variation was significantly reduced compared with the conventional predetermined polishing time method without EPD. Therefore, it is possible to achieve a global planarization without the complicated reverse moat etch process. As a result, the STI-CMP process can be simplified and improved using the new EPD method.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.19 no.1
• /
• pp.46-50
• /
• 1983

A reverse voltage commutating thyristor chopper was described. The chopper consists of commutating capacitor charging circuit and commutating thyristor. By superimposing the charged voltage on capacitor to load voltage. Powerful reverse voltage could be induced on main thyristor cathode. And in that wise the chopping action was performed without all the reactors of the proposed circuit. An energy recovery circuit was employed in the chopper circuit for recovering the energy that was consumed in main thyristor commutation. The operating principles of the chopper circuit was analyzed and experimental results were as following. I) All reactors were eliminated. ii) By applying energy recovery circuit to the chopper, 67% of the consumed energy was recovered to source. iii) Turn off time of the proposed chopper was derived as T=RC ln2.

• Journal of KIBIM
• /
• v.9 no.2
• /
• pp.21-28
• /
• 2019

Recently, many scan projects are gradually increasing for maintenance, construction. The scan data contains useful data, which can be generated in the target application from the facility, space. However, modeling the scan data required for the application requires a lot of cost. In example, the converting 3D point cloud obtained from scan data into 3D object is a time-consuming task, and the modeling task is still very manual. This research proposes Scan-to-Geometry Mapping Rule Definition (S2G-MD) which maps point cloud data to geometry for irregular building plane objects. The S2G-MD considers user use case variability. The method to define rules for mapping scan to geometry is proposed. This research supports the reverse engineering semi-automatic process for the building planar geometry from the user perspective.

• Membrane and Water Treatment
• /
• v.1 no.4
• /
• pp.273-282
• /
• 2010

Treatment and reuse of industrial wastewater is becoming a major goal due to water scarcity. This may be carried out using membrane separation technology in general and reverse osmosis (RO) in particular. In the current study, polyamide (FT-30) membrane was employed for treatment of wastewater obtained from Faraman industrial zone based in Kermanshah (Iran). The effects of operating conditions such as transmembrane pressure, cross flow velocity, temperature and time on water flux and rejection of impurities including COD by the membrane were elucidated. The aim was an improvement in membrane performance. The results indicate that most of the chemical substances are removed from the wastewater. In particular COD removal was increased from 64 to around 100% as temperature increased from 15 to $45^{\circ}C$. The complete COD removal was obtained at transmembrane pressure of 20 bars and cross flow velocity of 1.5 m/s. The treated wastewater may be reused for various applications including makeup water for cooling towers.

• Smart Structures and Systems
• /
• v.31 no.1
• /
• pp.79-88
• /
• 2023

As the number of deteriorated buildings increases, the importance of safety diagnosis, maintenance, and the repair of buildings also increases. Traditionally, building condition assessments are performed by one person or one company and various inspections are needed. This entails a subjective judgment by the inspector, resulting in different assessment results, poor objectivity and a lack of reliability. Therefore, this study proposed a method to bring about accurate grading results of building conditions. The limitations of visual inspection and condition assessment processes previously conducted were identified by reviewing existing studies. Building defect data was collected using the reverse-engineered three-dimensional (3D) model. The accuracy of the results was verified by comparing them with the actual evaluation results. The results show a 50% time-saving to the same area with an accuracy of approximately 90%. Consequently, defect data with high objectivity and reliability were acquired by measuring the length, area, and width. In addition, the proposed method can improve the efficiency of the building diagnosis process.

• Journal of the Korean Electrochemical Society
• /
• v.13 no.4
• /
• pp.277-282
• /
• 2010

Durability of automotive polymer electrolyte membrane fuel cell (PEMFC) strongly depends the startup/shutdown procedure. Formation of hydrogen/air boundary in the anode gas channel, so-called reverse current condition, particularly induces fast degradation of the cathode. Under the reverse current condition, high voltage is present at the cathode facing air in the anode gas channel and is a function of residual oxygen concentration in the gas channels, that increases with storage time and reaches 21% (air) eventually. In this study, effects of residual oxygen concentration in a PEMFC on degradation of the PEMFC.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.6
• /
• pp.396-405
• /
• 2019

Single-phase full-bridge inverters have shoot-through problems. Dead time is an essential way of solving these issues, but it distorts the output voltage and current. Dual-buck inverters are designed to eliminate the abovementioned problems. However, these inverters result in switching power loss and electromagnetic interference due to the diode reverse-recovery problem. Previous studies have suggested reducing the switching power loss from diode reverse-recovery, but their proposed methods have complex circuit configurations and high system costs. To alleviate the switching power loss from diode reverse-recovery, the current work proposes a dual-buck inverter with a coupled inductor. In the structure of the proposed inverter, the current flowing into the original diode is divided into a new diode. Therefore, the switching power loss is reduced, and the efficiency of the proposed inverter is improved. Simulation waveforms and experimental results for a 1.0 kW prototype inverter are discussed to verify the performance of the proposed inverter.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.152-157
• /
• 2001

This paper is to model a 3D-shape product applying mathematically the data acquired from a 30 scanner and using an Automatic Design Program. The research studied in th reverse engineering up to now has been developed continuously and surprisingly. However, forming 3D-shape sol id models in CAE and CAM. based on the research, the study leaves much to be desired. Especially, analyses and studies reverse-designing automatically using measured data after manufacturing. Consequently, we are going to acquire geometric data using an 30 scanner in this study with which we will open a new field of reverse engineering by a program which can design a 3D-shape solid model in a CDA-based program automatically. Utilization of this program make it possible to minimize time in designing a product and establish a ADS(Automatic design system) program library to using all of the data from reverse engineering.