• 한국구조물진단유지관리공학회 논문집
• /
• 제17권1호
• /
• pp.1-9
• /
• 2013

철골구조에서 지진력 저항시스템으로 많이 사용되고 있는 가새골조시스템은 중심가새골조(Concentrically Braced Frames, CBF)와 편심가새골조(Eccentrically Braced Frames, EBF)로 구분하여 KBC2009 건축구조기준에서는 서로 다른 반응수정계수를 적용하여 설계하도록 되어있다. 현행 내진설계기준에서 편심가새골조에 대하여 링크 타단 접합부의 종류에 따라 모멘트 저항접합일 경우 반응수정계수는 R=8, 비모멘트 저항접합일 경우 반응수정계수 R=7로 적용하여 설계하도록 규정하고 있을 뿐 편심길이의 영향을 고려하지 않고 있다. 본 연구에서는 편심가새골조 중에서 역V형가새골조를 대상으로 비탄성 거동을 파악한 다음 편심길이에 따른 반응수정계수를 산정하여 내진설계 기준에서 제시한 값과 비교한 결과 편심가새골조에 대하여 동일한 반응수정계수를 적용하는 것은 적절하지 않음을 확인하였다.

• 한국지진공학회논문집
• /
• 제8권6호통권40호
• /
• pp.13-22
• /
• 2004

연성 계수는 반응수정계수(R)의 핵심구성요소로서 내진설계에서 중요한 역할을 하는 계수이다. 본 연구에서의 연성계수()는 단자유도 구조물의 연성계수()에 다자유도 보정계수()를 곱하여 평가하였다. 단자유도 시스템의 연성계수는 지진하중을 받는 단자유도 구조물의 변위 연성요구도와 주기에 따른 비선형 동적해석으로부터 산정하였다. 다자유도 시스템의 영향을 고려하기 위한 다자유도 보정계수()는 기존의 연구에 근거하여 제시하였다. 철골 연성 모멘트 골조의 연성계수를 평가하기 위하여, 구조물의 층수, 골조시스템(외곽골조, 분배골조), 붕괴 메카니즘(강-기둥 약-보, 약-기둥 강-보), 토질조건 및 지진구역을 변수로 하여 총 108개의 예제 구조물을 설계하였다. 구조물의 층수, 붕괴 메카니즘 및 토질조건은 연성계수에 큰 영향을 미치는 반면, 골조 시스템 및 지진구역은 연성계수에 영향을 미치지 않는 것으로 나타났다.

• Earthquakes and Structures
• /
• 제12권6호
• /
• pp.643-652
• /
• 2017

One of the methods to strengthen the structures against the seismic lateral loading is the employment of the composite columns. A concrete-filled tube (CFT) has the cumulative advantages of steel and concrete. Concrete-filled steel tube columns have been widely used in the moment-resisting frame (MRF) structures, located in both non-seismic zones and high-risk seismic zones. In this paper, the results of studies on two important seismic parameters of ductility and the response modification factor (RMF) of the MRFs with CFT columns are submitted. While the studies are carried out, the effects of span length-story height ratio, the strength of materials and seismic behavior of MRFs are considered. In this regard, the ductility, RMF and the strength of 36 models of the steel MRFs with CFTs are analyzed. The fiber plastic hinges numerical simulation and pushover analysis method are used in the calculations. Based on the obtained results, the RMFs suitable for the 5-, 10- and 15- story frames are proposed.

• Wind and Structures
• /
• 제31권2호
• /
• pp.153-164
• /
• 2020

In the design of buildings, lateral loading is one of the most important factors considered by structural designers. The concept of performance-based design (PBD) is well developed for seismic load. Whereas, wind design is mainly based on elastic analysis for both serviceability and strength. For tall buildings subject to extreme wind load, inelastic behavior and application of the concept of PBD bear consideration. For seismic design, current practice primarily presumes inelastic behavior of the structure and that energy is dissipated by plastic deformation. However, due to analysis complexity and computational cost, calculations used to predict inelastic behavior are often performed using elastic analysis and a response modification factor (R). Inelastic analysis is optionally performed to check the accuracy of the design. In this paper, a framework for application of an R factor for wind design is proposed. Theoretical background on the application and implementation is provided. Moreover, seismic and wind fatigue issues are explained for the purpose of quantifying the modification factor R for wind design.

• Steel and Composite Structures
• /
• 제42권1호
• /
• pp.59-74
• /
• 2022

This study introduces a general reliability-based, performance-based design framework to design frames regarding their uncertainties and user-defined design goals. The Iterative-R method extracted from the main framework can designate a proper R (i.e., response modification factor) satisfying the design goal regarding target reliability index and pre-defined probability of collapse. The proposed methodology is based on FEMA P-695 and can be used for all systems that FEMA P-695 applies. To exemplify the method, multiple three-dimensional, four-story steel special moment-resisting frames are considered. Closed-form relationships are fitted between frames' responses and the modeling parameters. Those fits are used to construct limit state functions to apply reliability analysis methods for design safety assessment and the selection of proper R. The frameworks' unique feature is to consider arbitrarily defined probability density functions of frames' modeling parameters with an insignificant analysis burden. This characteristic enables the alteration in those parameters' distributions to meet the design goal. Furthermore, with sensitivity analysis, the most impactful parameters are identifiable for possible improvements to meet the design goal. In the studied examples, it is revealed that a proper R for frames with different levels of uncertainties could be significantly different from suggested values in design codes, alarming the importance of considering the stochastic behavior of elements' nonlinear behavior.

• 콘크리트학회논문집
• /
• 제13권6호
• /
• pp.544-552
• /
• 2001

우리나라의 지진위험도는 중 .약진 지역으로 분류될 수 있으며, 최근 자주 발생하지는 않지만 큰 지진(예를들면 판내부 지진)에 대하여 구조물이 저항성능을 가져야 한다는 것을 고려한다면 벽체의 성능평가는 중요하다고 할 수 있다. 본 논문의 내용은 내력벽 시스템 아파트 건물의 벽체에 대한 반응수정계수의 평가에 관한 것이다. 이를 위하여 반응수정계수에 관련한 기존 연구를 조사하여 반응수정계수의 구성요소를 분석하였다. 또한, 국내 내진기준에서 반응수정계수, 동적계수 산정의 문제점을 ATC와 UBC 기준들의 밑면전단력의 크기와 비교하여 나타내었다. 그리고, 아파트 벽체 및 전단벽에 대한 기존의 국내 .외 실험연구를 활용하여 그 구조성능을 평가하였으며, 이러한 연구내용의 결과를 기초로 허용응력도 설계용 지진하중을 규정하는 국내 내진규정의 내력벽 시스템에 대한 반응수정계수를 제안한다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.433-438
• /
• 1998

Design lateral strength calculated by current seismic design code is prescribed to be much lower than the force level required for a structure to respond elastically during design level earthquake ground motion. Present procedures for calculating seismic design forces are based on the use of elastic spectra reduced by a strength reduction factor known as "response modification factor, R". This factor accounts for the inherent ductility, overstrength, redundancy, and damping of a structural system. This study considers ductility and overstrength of the wall-type structure for investigating R factor. This means that R factor is determined from the product of "ductility-based R factor($R_$\mu$$) and overstrength factor($R_s$). $R_$\mu$$ factor is calibrated to attain the targer ductility ratio (system ductility capacity) and produced in the from of $R_$\mu$$ spectra considering the influence of target ductility, natural period, and hysteretic model. On the other hand, $R_s$ is more difficult to quantify, since it depends on both material and system-dependent uncertain parameters. In this study Rs factor was determined from the result of push-over analysis.-over analysis.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2000년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Fall 2000
• /
• pp.432-439
• /
• 2000

According as ground acceleration becomes to exceed gravity acceleration recently, design is impossible or economical efficiency is poor in existing seismic design method. So increase of seismic isolated bridges is currently in progress. However, because base isolation design method is developed in high seismic regions. it may not be compatible in Korea. Therefore, this research has objective to evaluate ductility of pier and response modification factor according to the ductility of pier in seismic isolated bridges and to adapt to seismic characteristics in Korea. For this purpose, nonlinear analysis is accomplished with so many time histories derived from spectral density function compatible with response spectrum described in the design code and base isolation system modeled linear system, bi-linear system, and friction system. Through application of the proposed method, we had result that it may be compatible that response modification factor for the seismic isolated bridges is smaller than half of that for the conventional bridges when natural period of structures exceeds proper level.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2002년도 추계 학술발표회 논문집
• /
• pp.189-196
• /
• 2002

The capacity of CFS piers has not been used to a practical design, because there is no guide of a seismic design for CFS piers. Therefore, the guide of a seismic design value is derived from tests of CFS piers in order to apply it to a practical seismic design. Steel piers and concrete-filled steel piers are tested with constant axial load using quasi-static cyclic lateral load to check ductile capacity and using the real Kobe ground motion of pseudo-dynamic test to verify seismic performance. The results prove that CFS piers have more satisfactory ductility and strength than steel piers and relatively large hysteretic damping in dynamic behaviors. The seismic performance of steel and CFS piers is quantified on the basis of the test results. These results are evaluated through comparison of both the response modification factor method by elastic response spectrum and the performance-based design method by capacity spectrum and demand spectrum using effective viscous damping. The response modification factor of CFS piers is presented to apply in seismic design on a basis of this evaluation for a seismic performance.

• 한국전산구조공학회논문집
• /
• 제30권2호
• /
• pp.185-189
• /
• 2017

일반교량 내진설계의 목적은 지진발생 직후에 긴급차량의 통과를 허용하도록 하는 '붕괴방지설계'의 수행이다. 도로교설계기준은 연성구조를 구성하여 '붕괴방지설계'를 수행하는 규정을 제시하고 있으며 이 과정에서 연결부분과 하부구조에 적용하는 응답수정계수가 핵심적인 역할을 한다. 하부구조 응답수정계수의 경우 도로교설계기준은 연성과 여용력을 고려한 계수인 반면 AASHTO LRFD 교량설계기준은 교량의 중요도를 핵심, 중요 및 일반으로 구분한 인위적인 인자를 추가로 반영한 계수를 제시하고 있다. 이 연구에서는 강재받침과 철근콘크리트 교각기둥으로 구성된 일반교량을 선정하고 도로교설계기준의 설계조건과 함께 하부구조 응답수정계수를 차등 적용하는 경우의 설계결과를 비교, 검토하였으며 이로부터 하부구조 응답수정계수의 차등 적용 시 설계기준에 요구되는 보완사항을 제시하였다.