• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.12 no.1
• /
• pp.39-45
• /
• 2001

Background and Objectives : A post-pubescent male classical singer has lower vocal register than a female classical singer. Countertenors who can produce higher vocal register like female classical singers with their falsetto voice and head resonance are recently active. The general purpose of this study is to analyze voice of countertenors and to determine the differences with those of classical singers. Materials and Methods : Four countertenors in Korea were examined using a videostrobos-copy and their voice were analyzed using aerodynamic, acoustic and voice range profile methods. Results and Conclusion : Countertenors could produce elevated fundamental frequency, voice intensity and mean air flow rate using large pulmonary capacity and head voiced falsetto. It means the presence of greater energy in countertenor is due to the more efficient conversion of the air flow to acoustic energy. But, they had unstable amplitude perturbation per each vocal cycle. The results indicated that countertenor is the acoustic products of different laryngeal mechanism with other classical register and it can be recognized as one of the registers of male classical singers.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.3
• /
• pp.247-255
• /
• 2013

In this paper, a soft switching DC-DC converter for AC module type photovoltaic (PV) module integrated converter is proposed. A push-pull converter is suitable for a low voltage PV AC module system because the step-up ratio of a high frequency transformer is high and the number of primary side switches is relatively small. However, the conventional push-pull converters do not have high efficiency because of high switching losses by hard switching and transformer losses (copper and iron losses) by high turns-ratio of the transformer. In the proposed converter, primary side switches are turned on at zero voltage switching (ZCS) condition and turned off at zero current switching (ZVS) condition through parallel resonance between secondary leakage inductance of the transformer and a resonant capacitor. Therefore the proposed push-pull converter decreases the switching loss using soft switching of the primary switches. Also, the turns-ratio of the transformer can be reduced by half using a voltage-doubler of secondary side. The theoretical analysis of the proposed converter is verified by simulation and experimental results.

• International Journal of Fluid Machinery and Systems
• /
• v.6 no.2
• /
• pp.56-74
• /
• 2013

Stall stagnations in the system of axial-flow compressors and ducts occur in transition from deep surge conditions to decayed or converged stall conditions. The present study is concerned with the boundaries between the deep surges and the stagnation stalls on the basis of analytical results by a code on surge transients analysis and simulation. The fundamental acoustical-geometrical stagnation boundaries were made clear from examinations of the results on a variety of duct configurations coupled with a nine-stage compressor and a single stage fan. The boundary was found to be formed by three parts, i.e., B- and A-boundaries, and an intermediate zone. The B-boundary occurs for the suction-duct having a length of about a quarter of the wave-length of the first resonance in the case of very short and fat plenum-type delivery duct. On the other hand, the A-boundary occurs for the long and narrow duct-type delivery flow-path having a length about a fifth of the wavelength and relatively small sectional area in the case of short and narrow suction ducts. In addition to this, the reduced surge-cycle frequencies with respect to the duct lengths are observed to have respective limiting values at the stagnation boundaries. The reduced frequency for the B-boundary is related with a limiting value of the Greitzer's B parameter. The tendency and the characteristic features of the related flow behaviors in the neighborhood of the boundaries were also made clearer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.148-148
• /
• 2012

A cutoff probe is the novel diagnostic method to get the absolute plasma density with simple system and less assumption. However, high density of ion flux from plasma on probe tip can make the error of plasma density measurement because the dielectric material of probe tip can be damaged by ion flux. We proposed a shielded cutoff probe using the ceramic tube for protection from ion flux. The ceramic tube on probe tip can intercept the ion flux from plasma. The transmitted spectrum using the shielded cutoff probe is good agreement with E/M wave simulation result (CST Microwave Studio) and previous circuit simulation of cutoff probe [1]. From the analysis of the measured transmitted spectrum base on the circuit modeling, the parallel resonance frequency is same as the unshielded cutoff probe case. The obtained results of electron density is presented and discussed in wide range of experimental conditions, together with comparison result with previous cutoff method.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.3
• /
• pp.306-320
• /
• 2010

Modern ultra-large container carriers can be exposed to the unprecedented springing excitation from ocean waves due to their relatively low torsional rigidity. Large deck opening on the deck of container carriers tends to cause warping distortion of hull structure under wave-induced excitation, eventually leading to the higher chance of resonance vibration between its torsional response and incoming waves. To handle this problem, a higher-order B-spline Rankine panel method and Vlasov-beam FE model was directly coupled in the time domain, and the coupled equation was solved by using an implicit iterative method. In order to capture the complicated behavior of thin-walled open section girder, a sophisticated beam-based finite element model was developed, which takes into account warping distortion and shear-on-wall effect. Then, the developed beam model was directly coupled with the time-domain Rankine panel method for hydrodynamic problem by using the fixed-point iteration method. The developed computational scheme was validated through the comparison with the frequency-domain solution on the container carrier model in linear springing regime.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1385-1389
• /
• 2005

This paper describes the design, analysis and manufacture procedure of the composite blade for hingeless rotor system of unmanned helicopters. Helicopter rotor system is the key structural unit that produces thrust and control forces for intended flight conditions. In this work, a hingeless rotor system is adopted, and base on the design requirements for rotor system, composite blade section design and calculation of material properties were performed. In order to avoid the unstable state such as resonance, vibration characteristics of rotor system were analyzed. Finally, this paper describes the forming and manufacture of composite blade.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.12
• /
• pp.88-94
• /
• 2007

A flexure hinge-based compliant stage driven by stack-type piezoelectric elements has high precision motion but small operational range due to the characteristics of the piezoelectric element. Since the common flexure hinges can be broken by excessive deflection when the displacement is amplified by a high amplification ratio, a flexure hinge mechanism for large deflection is required. A cartwheel-type flexure hinge has an advantage of larger deflection compared with the common flexure hinges. This study presents a rotation stage with cartwheel-type flexure hinges driven by a stack-type piezoelectric element. The characteristics and the performance of the rotation stage are described by the terms of principal resonance frequency, amplification ratio of rotational displacement, maximum rotational displacement and block moment, in which the terms are analyzed by geometric parameters of the rotation stage. The analyzed results will be used as the guideline of the design of the rotation stage.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.26 no.4
• /
• pp.365-370
• /
• 2017

In this article, a 20 kHz Titanium (Ti) ultrasonic waveguide system for a nano-surface reformation process was designed and fabricated. First, finite element analysis using ANSYS software was performed to find the optimal dimensions. The obtained anti-resonance frequency for the Ti transducer with the piezoelectric device was 20.0 kHz, which value agreed well with the experiment result of 20.1 kHz (0.5% error). To test the system, chromium molybdenum steel (SCM) 435 was chosen as a test-piece. The result proved that the reformed depth was $36{\mu}m$. In addition, hardness was measured before and after the process. The value was changed from 14 HRC to 21 HRC, which is 50% increasing rate. Finally, the friction coefficient test result showed that the surface coefficient was reduced from 0.14 to 0.10 (28.6% reduction). Based on the results, the Ti ultrasonic equipment is regarded as a useful device for nano-scale surface reformation.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.10
• /
• pp.1062-1068
• /
• 2009

In this study, the impact force levels of bang machine and impact ball were measured, then the heavy-weight impact sounds generated by the bang machine and impact ball were investigated. It was found that the heavy-weight impact sources generated through modal excitation, and the impact force of the impact ball was similar to that of real impact source. The heavy-weight impact sounds were also measured in the real apartments with different slab thickness and floor structures. The results showed that the floor impact sound levels in terms of $L_{iFmax,AW}$, generated by impact ball sounds were reduced by using the resilient isolators. The frequency characteristics of heavy-weight impact sounds at 125 and 250 Hz were consistent with the characteristics of impact force spectrum. However, the difference between the impact sounds and the impact forces were found at 63 and 500 Hz due to the resonance of the floor structure and flanking noise, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.3
• /
• pp.573-581
• /
• 1994

A microstrip antenna having a dual polarization and a smaller size than feed horn polarizer of F.R.R.S(Faraday Rotation Rotary Switch) is designed, in which GaAs MESFET switches are inserted for selective reception of RHCP or LHCP. For an accurate analysis of the resonance frequency, input impedance and radiation pattern of the circularly polarized microstrip antenna, finite difference time domain (FDTD) method is used. When the GaAs MESFET switch in the feeder is ON-stats, the truncated patch antenna has a gain of about 16.6dB including amplifier gain, while the switch is OFF-state, this has a isolation level of -24dB.