• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2011년도 전력전자학술대회
• /
• pp.200-201
• /
• 2011

본 논문에서는, 동기 전동기 구동을 위해 세 개의 Shunt Resistor를 이용하여 전류를 피드백 받는 방법에 대하여 분석한다. 특히 세 개의 Shunt Resistor를 이용하여 전류를 피드백 받는 경우 인버터 출력 전압의 크기에 따라 피드백 받은 상전류 정보의 왜곡이 발생하는 문제점에 대하여 분석하고 이를 해결하기 위한 새로운 방법을 제안하며, 실험 결과를 통하여 검증한다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권6호
• /
• pp.908-919
• /
• 1998

This paper describes implementation and simulation of Chua's oscillator circuits with a cubic non-linear resistor. The two-terminal nonlinear resistor NR consists of one Op Amp two multipliers and five resistors. The Chua's oscillator circuit is implemented with analog electronic devices. Period-1 limit cycle period-2 limit cycle period-4 limit cycle and spiral attractor double-scroll attractor and 2-2 window are observed experimentally from the laboratory model and simulated by computer for the presented model. Comparing the result of experiments and simulations the spectrums are satisfied.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 학술대회지
• /
• pp.628-635
• /
• 2004

The characteristic of thin film resistor with low TCR( temperature coefficient of resistance ) and high precision are studied. The thin film resistor for 1/4W was fabricated and characteristic of these resistors was investigated. The fabricated device had the thickness of $2.48{\leqq}$ and the resistivity of $0.27{\omega}mm$. The electrical characteristic was evaluated by HP 4339B and 4284A instruments with HP l6339A. The profile of trimmed structure was also measured by non contact interferometer. The change of resistance and TCR increased with increasing roughness and resistance. To reduce the effect of stress annealing treatment was performed in the range of 563 to 623 K after trimming. The characteristic was improved after annealing. It is expected the fabricated device can be useful for high precision and low TCR. Fabricated thin film resistor has average deviation of resistance less than $0.35{\%}$ and TCR within 60.60ppm/K.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 센서 박막재료 반도체재료 기술교육
• /
• pp.82-85
• /
• 2002

In recent years, the tantalum nitride(TaN) thin-film has been developed for the electronic resistor and capacitor. In this papers, this study presents the surface profile and sheet-resistance property relationship of reactive-sputtered TaN thin film resistor processed by buffer of Ti and Cr on alumina substrate. The TCR properties of the TaN films were discussed in terms of reactive gas ratio, ratio of nitrogen, crystallization and thin films surface morphology due to annealing temperature. It is clear that the TaN thin-films resistor electrical properties are low TCR related with it's buffer layer condition. Ti buffer layer thin film resistor having a good thermal stability and lower TCR properties then Cr buffer expected for the application to the dielectric material of passive component.

• 한국전기전자재료학회논문지
• /
• 제21권12호
• /
• pp.1111-1117
• /
• 2008

A transformer type superconducting fault current limiter (SFCL) is one of the fault current limiters which have been proposed to reduce the fault current in the transmission lines. This paper proposes the new circuit configuration of a transformer type SFCL and also investigates the operating characteristics of the transformer type SFCL containig the resistor in the tertiary winding. The proposed SFCL contains the resistor in the tertiary winding. The newly inserted resistor can divert the power which the High-Tc superconducting has to bear. Because the resistor in the tertiary winding relieves the power of the High-Tc superconducting, it is possible that the proposed transformer type SFCL can decrease the more larger fault current than the conventional SFCL with the same High-Tc superconducting. And the cost of the proposed transformer type SFCL can be reduced.

• 전기학회논문지
• /
• 제66권5호
• /
• pp.750-756
• /
• 2017

This paper presents a method for DC voltage control of HVDC system connection of offshore wind farms. In the event of fault in AC grid, HVDC system need to meet LVRT regulations. When HVDC system meet LVRT regulation, unbalance is caused between power input and power output for DC link. Therefore, LVRT regulation lead to DC voltage increase of HVDC system. To control the DC voltage increase, the chopper resistor can be suggested. In this paper, DC voltage suppression is proposed using chopper resistor and de-loading. The effectiveness of the chopper resistor was verified using PSCAD/EMTDC.

• 대한전기학회논문지:전력기술부문A
• /
• 제53권1호
• /
• pp.31-37
• /
• 2004

In this paper, the analysis result of the switching surge in substation including GIS(Gas Insulated Switchgear) has been described using the EMTP(Electro Magnetic Transient Program) program. After performing the modeling of the input data, we have reviewed the energization overvoltages of GCB(Gas Circuit Breaker) without closing resistor in 345kV network, according to the conditions of simultaneously operating switch and statistically operating switch. Firstly, it can be known that the energization overvoltage of single line is higher than that of parallel energized line. Secondly, the maximum energization overvoltage obtained in statistics switch is higher than one in simultaneous switch. From these results, it can be known that the phase-to-earth energization overvoltages of $\alpha$-$\beta$ section are less than 2.2 p.u when closing resistor is eliminated. Therefore, it is possible to consider the circuit breaker eliminated the closing resistor in $\alpha$-$\beta$ section.

• 한국초전도ㆍ저온공학회논문지
• /
• 제1권2호
• /
• pp.49-53
• /
• 1999

We fabricated a resistive superconducting fault current limiter (SFCL) with a shunt resistor in order to bypass the transient current at faults. The SFCL consists of a YBCO films coated with an Au layer (10$\Omega$ at room temperature). which is to disperse the heat generated at hot spots in the YBCO films, and a 5$\Omega$ shunt resistor. The minimum quench current of the SFCL was found to be 12.2Apeak. This SFCL successfully controlled the fault current to below 23 Apeak. Which is otherwise to increase up to 103 Apeak. With the shunt resistor, the temperature of the SFCL rose the temperature of the SFCL rose three times slower than without the shunt, whereby the SFCL is protected at high currents.

• 전기학회논문지P
• /
• 제59권4호
• /
• pp.450-455
• /
• 2010

The performance modeling of a $25{\mu}m$ pitch VGA ${\mu}$-bolometer with the self-aligned thermal resistor structure is carried out. The self-aligned thermal resistor can be utilized for the maximizing the thermal resistance and the fill factor of a bolometer, so the performance improvement can be expected. From the results of the performance modeling of the micro-bolometer with self-align thermal resistor for a $25{\mu}m$ pitch $640{\times}480$ microbolometer designed with $0.6{\mu}m$ minimum feature size, the drastic improvements of NETD from 38.7 mK to 19.1 mK, responsivity of 1.9 times are expected with a self aligned thermal resistor structure. The main reason for the performance improvements with a self-aligned thermal resistor structure comes from the increasement of the thermal resistance.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.212-213
• /
• 2006

Polymer thick film resistor paste was fabricated using various materials. Inorganic materials of carbon black and graphite were selected as fillers and epoxy resin was selected as organic material. Solvent with high boiling temperature was applied to adjust viscosity. A designed test coupon pattern was used to evaluate fabricated resistors. Aspect ratio of 1 was selected for evaluating resistor values. Electrical properties of fabricated resistors were measured and their values analyzed in relation to paste composition. PTF fabricated using carbon black as fillers achieved resistor value of $530{\Omega}/sq$.