• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.415-419
• /
• 2004

The U filter has been generally used to filter the output voltage of PWM inverter to the sinusoidal waveform. The resonant voltage on the output voltage of PWM inverter may be generated due to LC filter. This paper proposed the algorithm to damp the resonant voltage using the virtual resistor without decreasing the efficiency by the power loss in the real resistor The method is appled to the vector controlled induction motor driven by the PWM inverter with the LC filter. The simulation results are carried out to verify the performances of the proposed algorithm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.809-812
• /
• 2001

We were fabricated of NiCr thin film resistors on A1$_2$O$_3$and SiO$_2$/Si substrates by dc magnetron sputtering system. The AC characteristics of resistors were studied. The cut-off frequency were found >10 MHz for the resistors with 39 ohm value of Alumina substrates, but the cut-off frequency were found 400 kHz for the resistors with 168 ohm value of SiO$_2$/Si substrates. In high frequency applications, the substrate selection is the most important factor.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.782-784
• /
• 2002

Many compound semiconductors which have high carrier mobility and small band gap have attentive in application of various practical a field. Especially, InSb served for Hall device and magnetic resistor such as magnetic sensor because InSb thin film has high mobility. Many studies on InSb thin film deposition because In and Sb has been very different feature of vapor pressure($10^4$ times) When In and Sb deposited. In this paper studied it In and Sb deposited simultaneously using by method of co-sputtering deposotion. This process, get to effects of manufacture process simplification. After that this paper observed micro structure and electronic behavior of InSb thin film using by co-sputtering.

• Proceedings of the KIEE Conference
• /
• 2006.10c
• /
• pp.609-611
• /
• 2006

This paper describes a CMOS sub-bandgap reference using Pseudo-Resistors which can be widely used in flash memory, DRAM, ADC and Power management circuits. Bandgap reference circuit operates weak inversion for reducing power consumption and uses Pseudo-Resistors for reducing the chip area, instead of big resistor. It is implemented in 0.35um Standard 1P4M CMOS process. The temperature coefficient is 5ppm/$^{\circ}C$ from $40^{\circ}C$ to $100^{\circ}C$ and minimum power supply voltage is 1.2V The core area is 1177um${\times}$617um. Total current is below 2.8uA and output voltage is 0.598V at $27^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.1
• /
• pp.57-62
• /
• 2008

From the progressing results, it was found that thin film using 52 wt% Ni - 38 wt% Cr - 3 wt% Al - 4 wt% Mn - 3 wt% Si target has good characteristics for low TCR (temperature coefficients of resistance) and high resistivity. The optimum sputtering condition was DC 250 W, 5 mtorr, and 50 sccm and the proper annealing condition was $350^{\circ}C$/3.5 hr in air atmosphere. At these fabricated conditions, thin film resistors with TCR values of less than ${\pm}10ppm/^{\circ}C$ were obtained. The TCR of the packaged-samples made at proper fabrication conditions was $-3{\sim}15ppm/^{\circ}C$ after the thermal cycling and $-20{\sim}180ppm/^{\circ}C$ after PCT (pressure cooker test), we could confirm reliability for the thin film resistor and find the need for enduring research about packaging method.

• Proceedings of the KIPE Conference
• /
• 2012.11a
• /
• pp.211-212
• /
• 2012

This paper proposes a single current sensor control technique for controlling motors that use only a single DC-Link current sensing resistor to obtain the information of three line currents. However, the measurement is distorted due to the too narrow current pulse width in the shunt resistor. To solve this problem, the existing phase current reconstruction methods are voltage split methods. They have a disadvantage which makes noise. A new dedicated observer is applied to decrease noise problem. Experimental results showed the effectiveness of the proposed method.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2007.04a
• /
• pp.115-127
• /
• 2007

[ ${\blacktriangleright$ ] Various Factors to affect TC Reliability of 4 array RES has been Investigated through Simulation Tool and Daisy Chain Board Test ${\blacktriangleright$ Solder Joint Crack Mechanism of 4 array RES has been Examined Also, It has been Examined Thoroughly What Influence Each Factors gibes to TC Reliability and Why Those Factors gives an Influence to it ${\blacktriangleright$ BGA Type RES is Suggested to Improve TC Reliability (Patented) ${\blacktriangleright$ Through this Study, Best Design Parameter has been Optimized to Increase TC Reliability of 4 Array RES

• Journal of the Korean Ceramic Society
• /
• v.27 no.3
• /
• pp.337-344
• /
• 1990

As a function of sintering temperature and time, the electrical properties of ruthenium based thick film resistors were investigated with microstructure. The variatio of resistivity and TCR(temperature coefficient of resistance)trends of sintered speciman at various sintering temperature were different low resistivity paste(Du Pont 1721) from high one(Du Pont 1741). These phenomena are deeply relative to microstructure of sintered film. With increasing the sintering temperature for 1721 system, the electrical sheet resistivity decreased, but again gradually increased above 80$0^{\circ}C$. And TCR trends in 1721 system are all positive. On the other hand the electrical sheet resistivity of 1741 resistor system decreased with sintering temperature. And TCR trends variable according to sintering temperature. TCR of speciman sintered at $700^{\circ}C$ was negative value, and TCR of 80$0^{\circ}C$ sintered speciman coexisted negative and positive value. But in case of speciman sintered at 90$0^{\circ}C$, TCR was positive value. As results of this fact, it was well known that the charge carrier contributied to electrical conduction in 1741 resistor system varied with sintering temperature.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.721-723
• /
• 1999

Chua's circuit is a simple electronic network which exhibits a variety of bifurcation and attractors. The circuit consists of two capacitors, an inductor, a linear resistor, and a nonlinear resistor. In this paper, a transmitter and a receiver using two identical Chua's circuits are proposed and a equivalent wire synchronizations are investigated Since the synchronization of the wire transmission system is impossible by coupled synchronization, theory having both the drive-response and the coupled synchronization is proposed. As a result, the chaos synchronization has delay characteristics in the wire transmission system caused by the line parameters L and C.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.718-720
• /
• 1999

Chua's circuit is a simple electronic network which exhibits a variety of bifurcation and attractors. The circuit consists of two capacitors, an inductor, a linear resistor. and a nonlinear resistor. In this paper, a transmitter and a receiver using two identical Chua's circuits are proposed and a equivalent wire secure communications are investigated. A secure communication method in which the desired information signal is synthesized with the chaos signal created by the Chua's circuit is proposed and information signal is demodulated also using the Chua's circuit. The proposed method is synthesizing the desired information with the chaos circuit by adding the information signal to the chaos signal in the wire transmission system.